Question about 1999 Suzuki GSF 1200 Bandit S

1 Answer

How do you remove the pad pin when changing brake pads on a suzuki bandit 1200s k2when the pin is corroded and wont budge

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 185 Answers

If your changing to Pads and not putting the old ones back in, use WD40 on the pin and let it soak in. I normally rotate the pin with some plyers and then work it's way out. Make sure you soak the pin with WD40 and let it sit for aa fir while so it has time to soak in

Posted on Oct 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Suzuki VL 1500 Intruder LC REAR DISC RATTLE,HOW DO I REPLACE IT?


Hello Dale, this is an easy job on your bike. Use a flat head screw driver and remove the brake pad cover...it will pop off.
Remove the hairpin type clips off of the ends of the brake pad pins.... Use pliers & pull the brake pad pins out from the front of the rear brake caliper....Clean the rear brake caliper's piston with brake cleaner. Use a rag and wipe it clean...Reinsert the old brake pads into the caliper. Place a pry bar between the brake pads, then push the inner piston into the caliper body, this will allow room to install new pads.... Remove the old brake pads...Coat the brake pad pins and the new brake pads metal back plates with high-temperature grease.

Slip the new brake pads into the rear brake caliper, then push the brake pad pins halfway into the caliper. Slip the spring clips into place between the brake pads and the brake pad pins. Push the brake pad pins completely through the rear brake caliper. Push the hairpin clips back into the brake pad pin tips. Snap the brake pad cover onto the top of the rear brake caliper....

Pump the rear brake pedal until the pedal feels firm, indicating that the brake pads have closed around the brake rotor...No bleeding will be needed because the system was never opened - That's all there is to it...i hope this information is helpful & good luck with your bike.


11_23_2011_12_23_40_am.jpg

Nov 22, 2011 | 2003 Suzuki VL 1500 Intruder LC

1 Answer

How do I remove the front brake disc pads on my 2006 cs500f


12 mm wrench or socket to remove the caliper.
Once caliper off , compress the cylinders with c-clamp or big screwdriver.
Remove the pads, one at a time and take note if there is a difference between inner and outer.
Some have a pin that goes through the upper part of the pad, of course you'll have to remove the pin before the pad will come out.
Install the new pads, install pins if yours has pins, install the caliper and tighten.

NOTE: Before you test drive squeeze the front brakes severeral time to push out the calipers to the disc, otherwise when you go to stop there wont be any brakes unless you pump it back up first.
You shouldn't have to bleeed them or anything. you shouldn't have to add any brake fliud either.
Can be done in less than 1/2 hour.

Dec 03, 2010 | 2006 Suzuki GS 500 F

1 Answer

Should I open up the whole rear brake system to change the pads?


NO remove the caliper, remove the pad pin fit a screw driver in to the pads where the disk would sit and lever the piston back in...

Jun 29, 2010 | 2005 Suzuki Boulevard S83

1 Answer

How do i get the old pads out of a rear brake caliper of a suzuki bandit 600, 2000 plate


May I suggest a trip to your local library. Cycle repair books should be in 646 stacks of reference.

Oct 01, 2009 | 1999 Suzuki GSF 600 N Bandit

1 Answer

How do i replace my brake pads on a 1991 dr350


You didn't specify front or rear so I will hit both.
Start with the front. Refer to this diagram:
http://216.37.204.203/Suzuki_OEM/SuzukiDB.asp?Type=13&A=91&B=43
Unbolt bracket 13 from the fork leg, then remove the 2 brake pad retaining pins #12. The brake pads can then be removed. You will have to compress the spring #5 when putting the pads back in to be able to reinstall the pins #12.
On the rear, refer to this page:
http://216.37.204.203/Suzuki_OEM/SuzukiDB.asp?Type=13&A=91&B=49
You have one of two choices, either remove the rear wheel so you can drop the pads out by removing the brake pad retaining pins #13 or unscrew #8 from the caliper bracket then remove the caliper.

Sep 23, 2009 | 1993 Suzuki DR 350 S

1 Answer

How do I do a simple brake pad swap? Front on a 600cc bandit, for what that matters.


easy. take a "C" clamp and squeeze the break piston all the way back in the caliper keeping the old brake pads on when u do it so u dont screw up the piston. then put the new pads on and reinstall the caliper. then pump up the brakes

Jun 14, 2009 | 1998 Suzuki GSF 1200 Bandit S

1 Answer

87 suzuki samurai change front brake pads


the allen wrench bolts should be the correct bolts to remove brake caliper to allow access to pads.


hint: there will be only two bolts to remove and they will be the same maybe different lengths

May 02, 2009 | 1987 Suzuki Samurai

2 Answers

Suzuki bandit front brake discs


no they are different if you have a 1200 need to get them for the 1200 or the gs500e and f models or the RF900

Feb 22, 2009 | 1998 Suzuki GSF 1200 Bandit S

Not finding what you are looking for?
1999 Suzuki GSF 1200 Bandit S Logo

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...