Question about 1991 Cagiva Mito 125 - Lawson

1 Answer

Cagiva mito starting problems

Hi there i have a cagiva mito 125 lucky explorer 91 plate got teh bike started up fine on electric starter but riding bak i stopped and bike cut out electric start had failed so had to bump it howevere if you hard wire the starte it goes ansd if u bypass the relay it works does this mean i need a new starter relay

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cagiva Master
  • 40,748 Answers

Hi, Martin_harri sorry you can't find the first and best tool you ever bought for your Cagiva despair not for a mere $0 you can download another one. For more information about your issue and free downloads that you will need please visit the websites below. Good luck and have a nice day.Cagiva Mito Starting problem
cagiva mito not starting
Free Cagiva Motorcycle Service Manuals for download
http://www.oemmotorparts.com/oem2.asp?M=Cagiva
http://www.cagiva.nl/media/owner_manuals/?tx_motomondo_pi4%5Bmodel%5D=&tx_motomondo_pi4%5Byear%5D=-1&tx_motomondo_pi4%5Bmanual%5D=

Posted on Jan 21, 2016

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 55 Answers

SOURCE: speedo and rev counter not working

make sure your clip i the back is in all the way.

Posted on Nov 23, 2008

  • 3567 Answers

SOURCE: Starting problem

You probably need to add water to the battery or the battery is getting weak and needs to be replaced. Water should cover the top of the battery plates. Get a 1 or 2 amp trickle charger and charge the battery for a few hours.
The problem may now go away.

If it continues then put a volt ohm meter on the battery and see what voltage is present when revving the engine. The voltage should be about 2 volts higher than the listed battery voltage, as in 6v now 8v / 12v now 14v.
If not, have the dealer check the stator and rectifier/regulator.

Please rate this solution. (four diamonds would be nice) Thanks!

Posted on Apr 05, 2009

MakisRC51
  • 408 Answers

SOURCE: I want to buy 1990 aprilia af1 futura...is it

It has the same engine with Mitto but that engine is more fragile than that of the CBR's.
Don't buy it if you ask me.

Posted on Jul 03, 2009

  • 3 Answers

SOURCE: i want a manual for cagiva mito 125 year model

Go to, http://www.mmra.org.uk/marci/mito/
should be able to download the 1 you want

Posted on Aug 20, 2009

SOURCE: clicks whenever i hit the electric start

I made this a problem with my bike after a rebuild! Turned out to be a screw on the front starter relay right at the front (cross headed screw) wasnt fully screwed in, hence causing a bad earth and causing the clicking sound to appear to be coming from the relay switch under the seat.
You want to gurantee that it is an earth problem?? Try hitting the subframe with a metal spanner or flicking the footpegs up and down.. youll find it then starts first time!

Peace

Posted on Dec 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cagiva mito 125 evolution 2 will not start


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
Cagiva Mito Starting problem
Cagiva mito wont start plz help
http://www.carlsalter.com/pdfs/Cagiva_mito_ev%201994.pdf
Cagiva MITO EURO2 125 2004 parts OEM Motorparts
http://www.cagiva.nl/media/owner_manuals/?tx_motomondo_pi4%5Bmodel%5D=&tx_motomondo_pi4%5Byear%5D=-1&tx_motomondo_pi4%5Bmanual%5D=

Sep 24, 2012 | Cagiva Mito 125 Motorcycles

1 Answer

Carnt start my cagiva supercity 125


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and downloads that you will need please visit the websites below. Good luck and have nice a day.
Cagiva Mito Starting problem
Help Cagiva Mito won start BAR Bay Area Riders Forum
Service Manual Cagiva
http://www.oemmotorparts.com/oem2.asp?M=Cagiva
http://www.cagiva.nl/media/owner_manuals/?tx_motomondo_pi4%5Bmodel%5D=&tx_motomondo_pi4%5Byear%5D=-1&tx_motomondo_pi4%5Bmanual%5D=

Sep 20, 2012 | Cagiva Supercity 125 Motorcycles

1 Answer

Cagiva mito both headlights are not on at the same time


Hi, Anonymous for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. If necessary, transport your bike to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your problem. For more information about your issue and free downloads that you will need please visit the websites below. Good luck and have a nice day.
cagiva mito evo headlights
Cagiva mito 125 electrical lights problem
Free Cagiva Motorcycle Service Manuals for download
http://www.oemmotorparts.com/oem2.asp?M=Cagiva
http://www.cagiva.nl/media/owner_manuals/?tx_motomondo_pi4%5Bmodel%5D=&tx_motomondo_pi4%5Byear%5D=-1&tx_motomondo_pi4%5Bmanual%5D=

May 03, 2012 | 1993 Cagiva Mito 125 - Lawson

1 Answer

Hi my cagiva mito doesnt wont to turn on or start no light are appearing oil nutral petrol when i turn the key on and i have checked all the wires and no loss connection just brought new baterey and fuses...


Hi, Poingy21 and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
CAGIVA MITO 125
Cagiva Mito Starting problem
http://www.carlsalter.com/pdfs/Cagiva_mito_ev%201994.pdf
Cagiva MITO EURO2 125 2004 parts OEM Motorparts
http://www.cagiva.nl/media/owner_manuals/?tx_motomondo_pi4%5Bmodel%5D=&tx_motomondo_pi4%5Byear%5D=-1&tx_motomondo_pi4%5Bmanual%5D=

Aug 14, 2011 | Cagiva Mito 125 Motorcycles

1 Answer

Electric start problems , checked starter ok but will not turn engine over


Hi, Eddie85814 and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and downloads that you will need please visit the websites below. Good luck and have nice a day.
CAGIVA MITO 125
Cagiva Mito Starting problem
Free Cagiva Motorcycle Service Manuals for download
http://www.oemmotorparts.com/oem2.asp?M=Cagiva
http://www.cagiva.nl/media/owner_manuals/?tx_motomondo_pi4%5Bmodel%5D=&tx_motomondo_pi4%5Byear%5D=-1&tx_motomondo_pi4%5Bmanual%5D=

Apr 02, 2011 | 1991 Cagiva Mito 125 - Lawson

1 Answer

My bike is a cagiva mito evo 125 thieves tried to steal it and now it doesnt work what could be the problem? I've tried nothing to fix the problem yet


Hi, Doubleu120 and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Faulty starter button/switch.
6. Faulty jiffy stand or clutch pull in switch/sensor.
7. Security alarm needs a reset.
8. Starter control circuit, relay, or solenoid faulty.
9. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue and downloads that you will need please visit the websites below. Good luck and have nice a day.
CAGIVA MITO 125
Cagiva Mito Starting problem
Free Cagiva Motorcycle Service Manuals for download
http://www.oemmotorparts.com/oem2.asp?M=Cagiva
http://www.cagiva.nl/media/owner_manuals/?tx_motomondo_pi4%5Bmodel%5D=&tx_motomondo_pi4%5Byear%5D=-1&tx_motomondo_pi4%5Bmanual%5D=

Dec 18, 2010 | 2003 Cagiva Mito 125 Evoluzione

5 Answers

Clicks whenever i hit the electric start


I made this a problem with my bike after a rebuild! Turned out to be a screw on the front starter relay right at the front (cross headed screw) wasnt fully screwed in, hence causing a bad earth and causing the clicking sound to appear to be coming from the relay switch under the seat.
You want to gurantee that it is an earth problem?? Try hitting the subframe with a metal spanner or flicking the footpegs up and down.. youll find it then starts first time!

Peace

Nov 17, 2009 | 1992 Cagiva Mito 125 - Lawson

2 Answers

Starting problem


You probably need to add water to the battery or the battery is getting weak and needs to be replaced. Water should cover the top of the battery plates. Get a 1 or 2 amp trickle charger and charge the battery for a few hours.
The problem may now go away.

If it continues then put a volt ohm meter on the battery and see what voltage is present when revving the engine. The voltage should be about 2 volts higher than the listed battery voltage, as in 6v now 8v / 12v now 14v.
If not, have the dealer check the stator and rectifier/regulator.

Please rate this solution. (four diamonds would be nice) Thanks!

Apr 05, 2009 | 1992 Cagiva Mito 125 - Lawson

2 Answers

No start but electrics still work


dear no start have the battery tested should read 12.7volts for a full charge. also check connections on batt and on starter solenoid.

Mar 24, 2009 | 1999 Cagiva Mito 125 Evoluzione

Not finding what you are looking for?
1991 Cagiva Mito 125 - Lawson Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cagiva Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Steve P
Steve P

Level 3 Expert

3172 Answers

Are you a Cagiva Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...