Question about 2000 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

Haveing problems removing the forks on a harley davidson

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 72 Answers

You remove the axle 1st
the 2 large nuts on the top of triple tree next
on the lower portion of triple tree there is a bolt on each side remove it
the fork tubes should pull down and out
remove the top of triple trees
remove the cover in middle of triple tree under it you will find a loch nut and a special spannner nut remove both topp triple tree will come of
unlock triple tree twist lower tree it should slide out
reverse to install

Posted on Sep 05, 2009

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

OneRide
  • 379 Answers

SOURCE: 2001 harley davidson fat boy fork seals leak

Either the seals were not installed correctly or your tubes and sliders are excessively worn. Not changing the fork oil at recommended intervals will cause excessive wear. Overfilling the forks will cause leaks too.

Posted on Jun 04, 2009

tundrajet
  • 80 Answers

SOURCE: removing harley davidson ultra classic gas tank

Drain the fuel either by siphening or removing the cross over tube at the front of the tank and letting it drain that way or just block off those cross over lines and leave the fule in the tank for removal.

0) remove seat
1) drain fuel
2) undo cross over line (bottom front of gas tank.
3) shut off pet **** and remove fuel line from pet ****.
4)there should only be 2 bolts holding the tank on, one at the top front of the tank and one at the back of the tank.

All in all a pretty easy (but possibloy messy) job.

Posted on Jun 06, 2009

  • 124 Answers

SOURCE: remove ignition switch from 2000 harley-davidson

To remove the ignition switch turn the handle bar fully to the right, turn the ignition switch to access position and with the key in the switch depress the tab under the switch with a small screwdriver (the tab is to the lower left under the knob) and while pressing down on the key, turn the key counterclockwise about 60 degrees. At that point the switch will pull out of the housing.

Posted on Nov 17, 2009

  • 17 Answers

SOURCE: harley davidson flstc heritage softail 1997

The fork oil is a very specific job needing a manual and a special tool, I don't want to insult anyones mechanical knowledge but if you have never done it before, best to take somewhere else. Engine oil on the other hand is easy, the drain tube to any softail is on the right side by where the frame meets the swing arm, has somekind of plug in it. Start and run bike for a little while, long enough to get it warm but not hot. Remove fill plug and then remove plug in drain line. Using a peice of cardboard or something put in between filter and frame , directing the oil to your drain pan instead of where ever it goes. Put 1 qt oil back in (after everything is reinstalled) start the bike and make sure the oil light goes out, when it does shut bike off and fill to the point that when it is standing upright you get a little oil on the tip of your finger, over filling may result in loss of oil cap from pressure (been there)

Posted on Feb 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove a fork lock in a 2013 sportster


Hi, Larry for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Ignition fork lock switch 2008 Harley Davidson FXD
https://www.carlsalter.com/pdfs/Harley%20Davidson-2013-sportster-service-manual.pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2013 Harley Davidson 1200 Custom Owner Manual
Instant Tech Relief To speak to me personally absolutely "FREE"

Jun 11, 2017 | Harley Davidson Motorcycles

1 Answer

Harley has front end clunk


Hi Anonymous, unless you are having handling issues it's probably the front forks not having correct fork oil amount or the wrong weight, for more information on your question please visit the websites below and good luck: Harley Davidson Manuals Mark Workshop
Cycles Capacities and Fluid Requirements Fork Filling Quantities
How to Change the Fork Oil on 2012 Harley Davidson Street Glide

Dec 16, 2012 | 2005 Harley Davidson FLHRS - FLHRSI Road...

1 Answer

How do i change the oil in the forks


remove the allen type drain plug in fork bottoms?

Jul 16, 2012 | Harley Davidson Fork Oil

Not finding what you are looking for?
2000 Harley Davidson FXDWG Dyna Wide Glide Logo

1,029 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...