Question about 2001 Honda NSR 125 R

3 Answers

Hello i have a an nsr125 r 1999 and i need a bit of help. under the tank there is a green pipe in the middle of the tank underneath. im wondering if this is the fuel pipe and if it is were dose it go because i think this is the reason why my bike is not starting. thanks very much if you can help ben

Posted by on

  • bentimbrell Sep 04, 2009

    well ill tell you me story lol. the bike wouldnt engage at all so i tricle charged the battery last night. the bike engages now but dosent start. when i lifted the tank up the pipe underneath th tank has came off from the main part of the bike it dose smell of petrol. and also my friend said the bike sounds like thers no petrol in it. but iv got half a tank. so i was thinking that the pipe has come away. do you know were it needs to be fitting teperalory until i can get the garage 2miles away to get it sorted thanks

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

On the bottom left hand side of your tank, in the middle, there is a little black plastic tap, it says things like on/off/reserve, directly behind that on the steel it says the same thing...make sure you turn the tap so that On lines up with On on the steel plate behind it. There is a hose coming from the bottom of that tap, thats your fuel hose.. that hose should run to you carburetor Silver/grey thing under the air box ( big black plastic thing) you may need to remove the air box to see the carburetor, to do this you unscrew (but not all the way) the hose clamp (round silver ring with a little screw) and pull the whole air box off.. on the air box at the front, there is a hose.. maybe blue or green or clear... one end goes from the front of the air box down through the engine and does not attach to anything.. remember that you will see lots of little hoses/pipes that dont actually attach to anything, these are breather and overflow pipes... there is only one hose that comes from your fuel tank, and it goes straight (may be some bends and stuff) to your carburetor.. the oil line goes from your oil tank (the clear/milky tank to the front right hand side under the fuel tank) into the carburetor as well.. you will see a few little black tubes that dont attach to anything coming from the carb (breather lines)... so long as the oil and fuel lines are connected from the carb to their tanks, everything should be alright..

I hope this helps..

Posted on Sep 12, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,341 Answers

The green pipe may or may not be the fuel pipe.This is a 2 stroke as far as I remember nsr125...so the green pipe may also be carrying 2 stroke oil...Now for it not to start may be lots of reason and you need to start trouble shooting by different steps..Check fuel,flow of fuel to carb, check spark if there is any coming to spark plugs and so on....Hope this helps..

Posted on Sep 04, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Is there a fuel smell and is the tank have petrol (gas) in it ?

and does it turn over,

Posted on Sep 04, 2009

  • Roberta Smith
    Roberta Smith Sep 04, 2009

    there should be a fitting roughly at the side of the tank or likely toward the lowest point of the tank.



    where it attaches to the engine should be a fitting on the carb. also there should be a filter inline.



    tho you have not said i would suggest you buy a small bottle of gas line antifreeze and add a half of bottle next time you fill up. it will **** up any water in your petrol.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the clips of the gas tank on the 1990 XJ6 SOVERIGN


the tank is held in with straps within the boot behind the rear seat back.but the hard bit is removing the pipework. the filler hose and breather is easy.inside boot.but the flow and return pipes you may need quick release pipe tools, the flow/return pipes are underneath above the diff.not easy to get to. but are self sealing so when they are released no fuel should escape

Oct 12, 2015 | Cars & Trucks

1 Answer

Coolant leaking from expansion tank filler cap


Yes im sure it should have a rubber seal.only if the pipes are rock hard during running should u start checking head gaskets.the cooling system runs under pressure anyway but weakest point will give first.it will be a pressure cap so check into getting a new cap first

Aug 16, 2015 | Rover Cars & Trucks

1 Answer

Fluidmaster instructions


Turn off water at valve. Drain tank. Remove fill line that goes to bottom of tank. Remove large nut from underneath tank holding in old fill/float valve assembly. Clean area around hole in tank above and below. Get large black washer from kit put onto bottom of fluid-master pipe (lip side down). Place fluid-master into hole from top of tank to check height. Top of fluid-master valve should be even or just a bit below top of tank. To adjust hold head of fluid-master and turn pipe ccw to lengthen, cw to shorten. Once adjusted put into tank. Using large flat nut in kit tighten to tank, making sure its centered in the hole, no part of the float touching the sides of the tank, and that the small nipple on the side where the small black hose will attach is facing towards the overflow pipe. Make it nice and tight, but don\'t break it.Then re attach water supply line you removed earlier, hand tight only. Place pipe clip onto top of overflow pipe (funny looking plastic clip with metal piece attached). Attach small black hose to fill valve nipple on side of valve, other side to funny clip. You may need to cut it shorter so it doesn\'t kink. Tun on water and adjust float if required. Level should be 1/2" below top of overflow pipe.

Aug 23, 2014 | Home

1 Answer

Where is the fuel pump fuse for 2001 jaguar vanden plas


if its a v12 or super charged vehicle it has two inside the fuel tank, only one pump if it normal aspirated, remove the tank and you will find the pump/s under the round panel on top of the tank with the fuel level sensor/ you will need some pipe release tools to get the flow and return pipes out of the bottom of the tank, a bit of a pig to get to has they are under the vehicle above the differential, but have self sealing valves in the bottom of the tank so you dont get soaked!

Apr 01, 2013 | Jaguar Vanden Plas Cars & Trucks

2 Answers

I have a 97 ford taurus and its a clunker. Im getting rid of it. It got a full tank and i would like to siphon it out and into my new car. I got a siphon kit and fed the tub all the way in till i wouldnt...


unfortunately most fuel tanks are made so you can no longer siphon gas through the fill tube. if you want the fuel that badly you could disconnect the fuel line from the fuel filter and wait for it to drip out.

Mar 31, 2011 | 1997 Ford Taurus

2 Answers

I got my piston in my ktm sx 125 blown up im wondering must i open the entire engine to fish out the bits i don't fink dat are there?? my crankshaft spins freely in the crankcase not rubbin on any bits of...


Thanks for contacting FixYa. I was reviewing some of the older un-answered questions trying to ensure your issue has been resolved.

You should be able to resolve this issure by just removing the top end. You will have to remove the tank, the pipe, disconnect the carb, any water hoses, and possibly the radiator. If there is no damage to the connecting rod you be able to thoroughly clean the crankcase withough removing the engine. If you have damage to the top rod end you will have to pull the engine and split the case to replace the connecting rod.

TF

Jan 28, 2011 | 2004 KTM SX 125

1 Answer

When saw is running it dies unless i undo the vented gas cap then the saw will keep going is there any other way on other than the gas cap for it to vent or help breath? on a 372 xp


The vent on the 372 is not in the cat, it is situated on the right hand rear side of the fuel tank, the early vent was a black pipe pressed into the tank with a white ( vion ) plug in it, this can be pulled out by screwing a self tapping screw into the middle of it and pulling out with a pair of pliers, the later breather is in the same place but consist of a green valve pressed into the tank, it then has a black pipe conected to it which comes up into the crankcase and sits onto a nipple under the air filter, this can be pulled out with a pair of pliers and replaced, the later breather is very prone to blocking, due to CE law and gas escape from fuel tanks the breather is very fine.

Jan 25, 2011 | Husqvarna Operator's Manual 365 372xp ...

2 Answers

How do I replace the Fuel Pump in my 2002 Cadillac Seville SLS


Hello ray......

The fuel pump is located inside the fuel tank. You can access the fuel tank thru the trunk. Inside the trunk and underneath the carpet, there is a access panel. Remove the five screws and lift the access panel. There under the panel you will see the pump. Disconnect it and take it to the auto parts store as they usually want the old one for an exchange. Joe


Thanks for choosing Fixya!

Dec 16, 2010 | Cadillac Seville Cars & Trucks

1 Answer

Removal of the petrol tank


The 93 xj6 tank is in the trunk behind the spare tire and battery, While there are two straps holding it, they will not be rusty because they are inside the trunk. After disconnecting everything in the trunk, jack up the car (use jack stands) crawl under and disconnect the two clips holding the fuel lines to the tank. There are two holes in the trunk under the tank that let the lines through.
Now the tank will pull right out.

May 15, 2009 | 1993 Jaguar XJ6

1 Answer

Putting my fdw60 aquarius dishwasher back together


check that the place where u put the salt in is screwed in tightley, then, i find giving the dishes a hand wash and they come up clean , ti will work fine, because if you notic, take a glass with white powdery residue out of the dishwasher and rinse it under water, and the residue is still there, so they need a good scrub and after that , they can be washed as normal!

Jul 03, 2008 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
2001 Honda NSR 125 R Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...