1993-2002 Camaro INSIDE REAR VIEW MIRROR REMOVAL?

The mirror is attached inside the door, you must remove the door panel, the part you think is just a cover doesn't come off.

glass and motor availbable separately

Removal
NOTE: Do not remove the mirror assembly when repairing the individual mirror part. Individual mirror parts can be installed without removing the mirror assembly.

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the outside rear view mirror access water shield.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect and remove the speaker.

1. Disconnect the outside rear view mirror electrical connector.

1. Remove the outside rear view mirror.
   1. Remove the nuts.
   1. Remove the outside rear view mirror.
      • Feed the outside rear view mirror wiring through the opening in the front door.

here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal

1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).
   
   
   
   
   

1. Remove the wire clip.
   

1. Disconnect the power outside rear view mirror electrical connector.
   
   
   
   
   

1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.
   
   
   
   
   

Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal

1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
   

1. Remove the two outside rear view mirror inside mounting hole cover screws.
   
   
   Remove the outside rear view mirror mounting hole cover.

Installation
To install, reverse the removal procedure. Mirror Control
Removal

1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).
   
   
   

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

You can just pull it off but you'll have to glue it back on.

Mirror — Outside Rear View Removal
NOTE: Do not remove the exterior mirror assembly when repairing an individual part. Individual components can be installed without removing the exterior mirror.

1. Disconnect the battery ground cable (14301).

1. Remove the front door trim panel; refer to Section 501-05.

1. Remove the speaker.
   1. Remove the screws.
   1. Disconnect the electrical connector.
   1. Remove the speaker.

1. Remove the outside rear view mirror (17682).
   1. Disconnect the power mirror wiring clips.
   1. Remove the outside rear view mirror nuts.
   1. Remove the outside rear view mirror.
      • Feed the power mirror wiring through the opening in the front door (20124).

Installation

1. NOTE: When the battery (10655) is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.
   To install, reverse the removal procedure.

SECTION 501-09: Rear View Mirrors 2001 Villager Workshop Manual REMOVAL AND INSTALLATION Mirror —Exterior Rear View Removal

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

1. Remove the upper speaker.
   1. Disconnect the electrical connector.
   1. Remove the bolts.
   1. Remove the speaker.

1. Position the watershield aside.

1. Remove the exterior rear view mirror access panel.

1. Disconnect the exterior rear view mirror electrical connectors.
   • Release the wiring harness locator.

1. Remove the exterior rear view mirror.
   • Remove the bolts.
   • Feed the wiring harness through the door opening.

1. Remove the front door trim panel (23942) ; refer to Section 501-05 .
   • Peel back the watershield.

1. Remove the rear view mirror mounting hole cover (17K709).

1. Disconnect the power mirror electrical connector.

1. Remove the outside rear view mirror (17682).
   1. Remove the screws.
   1. Remove the outside rear view mirror.

please rate as fixya if this works for you.

You can manually push the mirror left or righ or up and down. It just ratchets on the plastic screw adjusters. It won't do any damage.
If you have floding mirros, make sure they are locked into position.

here's what inside looks like of 2002 mirror. I don't have 2005


SECTION 501-09: Rear View Mirrors 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation
All vehicles

1. Remove the front door trim panel (23942). For additional information, refer to Section 501-05 .

Vehicles with Mach 40 speakers

1. If equipped, remove the speaker grille.

1. Remove the speaker bracket.
   1. Remove the screws.
   1. Remove the speaker bracket.
   • Disconnect the speaker electrical connector.

Vehicles with speaker delete panel

1. Remove the speaker delete panel screw cover.

1. Remove the speaker delete panel.
   1. Remove the screws.
   1. Remove the panel.

All vehicles

1. Disconnect the power exterior rear view mirror electrical connector.

1. Position the water shield aside.

1. Remove the power exterior rear view mirror nuts.

1. Remove the power exterior rear view mirror.
   1. Push down on the mirror assembly to release the mirror flange.
   1. Roll the mirror assembly down and rearward.

There are two tiny motors in each mirror. one for up/down. One for side to side. They have jack screws (plastic) that fit into the motors.

You can manually put your hands on either side of the mirror and force adjust it. If you hear a ratcheting sound, the jack screws are OK. Then repeat with hands on top and bottom.

If you hear ratcheting and mirror stays where you stop it, that means one of the motors is bad. The motor assembly is available as a separate part.

-------------------------------------------------------------------------------------
Mirror Motor—Crown Victoria, Grand Marquis
Removal and Installation

1. Disconnect battery ground cable. Refer to Section 14-01 .
   

1. Remove outside Rear View Mirror Glass as outlined.
   

1. Remove Outside Rear View Mirror as outlined.
   

1. Remove two screws from outside rear view mirror motor.
   

1. Remove outside rear view mirror housing from outside rear view mirror base.
   

1. Disconnect connector and remove outside rear view mirror motor from mirror housing.
   

1. To install, reverse Removal procedure.
   

Might be cheaper to buy used irror at car-part.com. Look for * to find page with cheapest part. Or, EBay. Good luck