Question about Honda Motorcycles

1 Answer

Will not turn over 1986 honda Spree

1986 honda spree starter won't engage? Horn & rear brake light work, no head lite, hi or low, no turn signals, electric starter not working. Kick starter gives a spark to plug. Has not run in a couple of years. New battery @

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Honda Master
  • 57,416 Answers

Hi, Jack before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://hondaspree.net/phpBB3/viewtopic.php?f=3&t=34313
https://www.reddit.com/r/MechanicAdvice/comments/1ozan0/1986_honda_spree_starting_issues
Honda Spree NQ501 Manual
https://www.partsfish.com/page/oem-parts-for-honda
https://absolutelyscooters.net/pdf/CGEN_dawg_scooter_manual.pdf

Posted on Jul 12, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 393 Answers

SOURCE: changed battery real cranky no start

check the fuses and circuit breakers near battery i'll bet one of them popped.

Posted on Nov 16, 2008

  • 69 Answers

SOURCE: Yamaha vino 50 cc scooter

hello, check to see if it is a switch (pull hand brake back when starting

Posted on Nov 25, 2008

  • 48 Answers

SOURCE: 1986 F150 Brake Lights don't work.

i would look at your brake light switch if you say all the fuses are good.look above where you put your foot on the pedal you should see a switch on a bracket so that when the pedal is pressed the plunger on the switch moves out and makes the lights come on. link the cables together that go on the switch and the brake lights should come on. if they dont check at the switch to make sure that one of those cables is live, the other one should go to the lights at the back. hope this helps.

Posted on Apr 24, 2009

  • 1 Answer

SOURCE: 2002 Jeep Grand Cherokee - Brake lights not

The problem is that the tail lights, light bulbs get too hot and melt the plastic where the bulb socket goes into the lens assembly. On the lens assembly you will see one to three metal tabs where the socket fits into. Lift up the tab a little bit with a screw driver and place a small amount of either metal or plastic underneath the tab so it will get a good connection. It will fix the problem.

Posted on Aug 09, 2011

  • 2 Answers

SOURCE: Electrical problem. Turn signals, brake light.

spray contact cleaner on the switch and with the brake lever removed push your finger on the switch and work it .On mine I twisted the switch a little with my finger while the switch was pushed in and got it working.fine

Posted on Aug 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 caravan headlights stay on. And no tail lites but brake lites and turn signals still work and horn beeps randomly on its own.


Replace the turn signal switch. All exterior lights run threw it, except the high mount brake light. The horn also. If the head light switch is on the handle, this should take of it also. If the headlight switch is in the dash, you might have to replace it also if they stay on.

Sep 27, 2016 | 2000 Dodge Caravan

1 Answer

Specifically I'm trying to identify the wire on the spark plug coil assembly to which I should connect the signal wire of a Tachometer to. The wire colours are, red, yellow, green/white, and blue.


It says the tachometer wire is Yellow/Green, you do not have that listed. You will find it in the list below, it is highlighted..

WIRING INFORMATION 2001 Subaru Legacy






WIREWIRE COLOR LOCATION

12V CONSTANT WIRE WHITE Ignition Harness

12V IGNITION WIRE GREEN Ignition Harness

12V ACCESSORY WIRE YELLOW Ignition Harness

STARTER WIRE WHITE/BLACK Ignition Harness

POWER DOOR LOCK (-) WHITE Harness In Driver's Kick Panel

POWER DOOR UNLOCK (-) GREEN/RED Harness In Driver's Kick Panel

PARKING LIGHTS (+) ORANGE At Light Switch

DOOR TRIGGER (-) PINK/BLACK In White Connector Behind Fuse Box

TRUNK TRIGGER (-) YELLOW/BLUE In White Connector Behind Fuse Box

TRUNK RELEASE (5-wire) LT.GREEN/YELLOW At Motor In Tail Gate

FACTORY ALARM ARM (-) Factory remote only

FACTORY ALARM DISARM (-) Factory remote only

TACHOMETER YELLOW/GREEN At Ignition Coil

BRAKE WIRE (+) WHITE/BLACK At Brake Pedal Switch

HORN TRIGGER (-) RED/GREEN Harness At Steering Column

LEFT FRONT WINDOW UP BLUE/RED At Driver Window Motor Inside Door

LEFT FRONT WINDOW DOWN BLUE At Driver Window Motor Inside Door

RIGHT FRONT WINDOW UP BLUE/RED Harness In Driver's Kick From Driver Door

RIGHT FRONT WINDOW DOWN BLUE Harness In Driver's Kick From Driver Door

LEFT REAR WINDOW UP BLUE/RED Harness In Driver's Kick From Driver Door

LEFT REAR WINDOW DOWN BLUE Harness In Driver's Kick From Driver Door

RIGHT REAR WINDOW UP BLUE/RED Harness In Driver's Kick From Driver Door
RIGHT REAR WINDOW DOWN BLUE Harness In Driver's Kick From Driver Door

Feb 07, 2016 | 2001 Subaru Legacy

1 Answer

Why would my horn and break light stop working on my 2006 Harley Davidson sportster 1200 xl custom at the same time. Swapped batteries blew a main oem 30 amp swap all works except horn and break lite


Hi Anonymous, check your horn button for continuity, always check fuses and bulbs first for broken filaments. Then check the connection at the rear fender wiring harness, inspect for corroded, broken or loose pins. Use a dab of dielectric grease and repair as necessary. Check your brake relay if you have one , check your brake light switches for continuity, some models rear turn signals were single filament bulbs only, no running light. If all else fails get out your test light and start tracking the power wire from the harness connection. For a free wiring diagram please visit the website below and good luck: Harley Davidson Manuals Mark Workshop

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jul 04, 2015 | Harley Davidson Motorcycles

1 Answer

Tw200 electrical schematic


hi
few things
new batteries only hold a little charge in them
so make sure it is fully charged
if your bike is making a clicking noise when you press the starter but is still not turning it is your starter solenoid
if it is making a clicking noise then your starter motor has seized and your solenoid is ok
if not making a clicking noise
it is possible your starter solenoid is broken and will need replacing
easy test is the starter solenoid has two electric poles on it
one going to the battery the other going to your starter motor
get a large spanner (wrench)
and with the ignition turned on
touch both poles with the spanner
("caution") this will spark a little so make sure there is no fuel close by
if the engine turns over
then your solenoid needs replacing

Aug 26, 2017 | Motorcycles

1 Answer

Honda bali sj 50, the electric ignition crashed just as the horn and turn signals. The light works. thereafter to put the bike to work wearing the kick, but now this kick also not working very well, so I...


Hi, Miguel before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
HELP Honda bali 50cc moped starting problem no power cuts out
Scooter Troubleshooting Scooter won start All about Scooters
http://www.hondampe.com.au/docs/owning_a_honda/owners_manuals/motorcycles/SK50M-1992.pdf
http://www.partsfish.com/page/oem-parts-for-honda
http://www.family-motorsports.net/GY6-50cc-150cc.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Sep 11, 2013 | Honda Motorcycles

1 Answer

I have a 92 Buick roadmaster. How do i get my brake lights to work on the rear of my car? The light in the window works fine including all the rest of my lights. I've changed the brakes switch and bulbs...


The lower brake lamps are wired through the turn signal switch. The hi-mount brake lite is wired differently. Do the rear turn signals work? If so, I think the problem is the turn signal switch. Your lower brake lites and turn signal use the same bulb filament, just not at the same time. Just my opinion.

Aug 28, 2017 | Cars & Trucks

1 Answer

2008 Honda VTX1800T Hyper-Lite 3Way Kit not working properly


Hi, Anonymous you may need a load equalizer for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.vtxcafe.com/showthread.php/84742-Installation-of-LED-system-caused-all-signals-to-fail
https://motosvit.com/HONDA%20vtx1800/Manual.pdf
http://www.partsfish.com/page/oem-parts-for-honda
Honda 2005 VTX1800C Owner Manual
Honda VTX1300T Touring 2008

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Mar 29, 2017 | 2008 Honda VTX 1800 F

1 Answer

1983 honda vf 750 magna one turn signal light and horns not working


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Turn Signal Indicators not working
83 Honda V65 Magna horn problems Motorcycle Forum
Honda 1986 VFR 750F Shop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda 1986 VRF750F Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jun 05, 2012 | Honda VF 750 C Magna Motorcycles

1 Answer

1986 Honda VT 1100 C rear running lights not working


Hi, Anonymous and the usual suspects are:
1. Bulbs are burnt out.
2. Light circuit fuse was blown.
3. Faulty ignition switch.
4. Faulty, corroded or cut wire connector, pins, sockets etc. in the running light circuit.
5. Loose, broken or corroded common ground.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Rear Running Light not Working Shadow Sabre
Honda shadow fuse box
Honda SHADOW VT1100 Owners Workshop Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda Shadow VT1100 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Apr 17, 2012 | 1986 Honda VT 1100 C

1 Answer

1985 Honda VT 500 C Shadow wiring diagram


Hi, Brian for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. 1985 Honda VT 500 Shadow wiring diagram Google Search
Honda Motorcycle Wiring Diagrams
http://www.cycleterminal.com/Service-Manuals/Honda-VT500C-Shadow-Service-Manual-English.pdf
http://www.partsfish.com/page/oem-parts-for-honda
http://mybikemanuals.com/honda/honda-vt-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Jan 24, 2012 | 1985 Honda VT 500 C Shadow

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5914 Answers

Marvin
Marvin

Level 3 Expert

85108 Answers

richard libby

Level 2 Expert

208 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...