Question about Factory Motorcycles

1 Answer

What are factory carb settings k760 petrol saw

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 112 Answers

I do not know but will try this, on my saws there are 2 holes with flat blade screw heads down in there , beside this hole is a number 1.5 3 2 ? these indicate how many turns out from set in in but not seated tight, then unscrew out that many turns or half as indicated.
otherwise try 1.5 L and 2-3 H these are the high rpm and low rpm settings each affects the other, so get it to idel the hold it open adjust high then adjust idle again, typically the L will run a bit rich and the H will run a bit lean, get it started and go back and forth youll get it,, Or not Sorry? CD

Posted on Mar 15, 2019

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: how to adjust carb. settings on a McCulloch Pro Mac 610 chain saw

turn both jets in untill snug (don't force) turn out ccw one full turn. increase by 1/8 turns untill set proper. should be between 1 1/4 and 1 1/2 normally. good luck. be safe.

Posted on Sep 21, 2008

jeffhercequi
  • 24 Answers

SOURCE: Factory carb settings for this saw? Could ssome one help me with this ?

What kind of saw is it???
on average low jet is about 1 1/2 turn counterclockwise out after bottoming out the jet slightly
high jet about 1 turn counterclockwise after bottoming jet out clockwise

hope this helps getting your saw going

Posted on Dec 04, 2015

Testimonial: "It is a jonsered 2149 turbo"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is throttle stuck wide open?


Could be a couple of things. could be a return spring sticking on the carb, or the throttle cable has frayed and sticking on. I've added the breakdown manual for you.
http://www.mediafire.com/download/68zm589mejh8jnq

Dec 20, 2015 | Husqvarna-Target Husqvarna K760 14 Inch...

1 Answer

Saw runs at normal idle with choke pulled and wide open with choke off


I would take it back to the repair person you used and let them know that they fixed one problem and caused another.

Jul 09, 2014 | Husqvarna 12"" K760 Concrete Saw"

1 Answer

What are the factory settings for the carbs on a ZZR400. I am having trouble getting the bike to run/idle properly.


Generally all carbs from the factory have a mixture screw setting of between 1 1/4 and 1 1/2 turn out from being bottomed out. Then I would check the sync on the carbs next. If that doesn't cure it then you can call a parts dept and ask them what the factory jets are and verify that you have those installed. Unless you have a pipe or full exhaust they should be factory. If you have aftermarket exhaust of slip on then you might have to dig a little deeper and see if it has factory parts or a jet kit.

I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_5bac37c3cb991fdb

Nov 02, 2013 | 1993 kawasaki ZZR 400

1 Answer

Husqvarna k760 will not prime and/or run properly


Get a carb. rebuild kit ,these models have carb.problems and need rebuilding,shop charges 70.00,get kit for 10.00 and diy.

Dec 11, 2012 | Garden

1 Answer

Toshiba SD-K760 region codes.


I found this on another site, worked for me, hope it helps...

icon_minipost.gifRegion code hack posted by Stratos, April 30 2006:
1. Press the Open button on your remote control to open the drive tray
2. Press the 2403960 button on your remote control
3. Press the 1 button on your remote control to change the region to 1, 2 for region 2, and so on, or 9 for multi-region playback. New region number will appear on screen.
4. Press the Open button on your remote control to close the drive tray
5. Power off the DVD player
6. Power on the DVD player

Jan 17, 2008 | Toshiba SD-K760 DVD Player

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Factory Experts

ray gallant

Level 3 Expert

60412 Answers

 steve
steve

Level 3 Expert

22172 Answers

txslim55
txslim55

Level 3 Expert

1104 Answers

Are you a Factory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...