Question about 1998 Honda CBR 1000 F

1 Answer

Clutch leaver assembly just bought think ther may be spring missing ? leaver seems to rattle about but works ok cbr 1000 f 1998

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 45 Answers

Adjusted, it will still wiggle a bit. same as my 03cbr954rr

Posted on Aug 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rattle in clutch pack


By the sounds of it u have a clutch plate missing or not in the right place or your clutch spring are worn out. Hope this helps

Dec 14, 2012 | kawasaki Motorcycles

1 Answer

Peugeot 505 1990. No resistance at clutch pedal. Hydraulic fluid ok to cylinder at flywheel. Removed this hydraulic cylinder and lever going to clutch itself. This leaver has little or no spring? I am not...


replace the clutch master. clutch master is a set of springs and rubbers located inside your hydrovac that is responsible for pushing your clutch fluids

Aug 17, 2011 | 1987 Peugeot 505

1 Answer

My 2000 cbr 929 engine works awesomely. There seem to be a rattling sound on the right side of the engine when the clutch cable is pulled the sound disappear. Is it normal for the clutch box of this model...


hi mate,mine 929 do the same noise as well from 30.000km till today 66.000km.everybody says that it is an old cbr's issue.when it will get much much worst just change the clutch plates not the discs if no need...i am used to that noise and i like it..it gives personality!!!

Aug 26, 2010 | 2001 Honda CBR 929 RR Fireblade

1 Answer

74 honda TL125 with a free play feel in the clutch leaver


On most bikes, there is a rod going down the center of the clutch. The lever on the case pushes this rod in when you squeeze the lever on the handlebar. If the rod going through the clutch will not move, the clutch will not release. It doesn't move very much, maybe a few millimeters. If you cannot remove the rod[you may have to use a magnet to pull it out] then the rod is bent. This could have happened if you assembled the new clutch incorrectly. If the sequence during reassembly was wrong, the disks were jammed. When you squeezed the clutch lever, something had to give. The clutch rod.

Sep 21, 2009 | 2008 Buell Blast

1 Answer

Push in clutch lever play even with new cable on my 74 TL125


It still sounds like that roller ball is missing. Do you have a manual to check for exact location? Yamahas have them on the casing side but not sure about Hondas. It is REALLY easy to drop out without being seen.

Parts in that casing do not usuall "weld" themselves together unless someone has really been abusting the clutch. Could be the clutch spring has lost some tension but no way to tell without comparing it with a new one. If you had a manual or even a friendly dealer you could find out proper specs. for the spring and then measure yours.

Don't just start replacing parts without verifying they have failed. It can just get expensive and not solve anything.

If you have a digital camera, take a picture of the assembly you believe to be seized together and email me at robertlanglois6@sympatico.ca
I will see what I can figure out.

How many hours / km on the bike? Clutch plates may be kaput but you don't mention clutch slipping?

Don't cut the cable yet. If you do, just trim it to about mid adjustment. It is easy to cut a bit more than cut too short! Either way, cutting is a bodge job. Best to find root cause and fix it.

Send me pictures if you can.
Rob

Sep 21, 2009 | 2008 Buell Blast

1 Answer

Clutch rattle and notchy gearchange


dear sir the springs in your clutch is what puts pressure on clutch discs. these springs should all be the same length they should be measured with a caliper and compared to specs . the notchy feeling on your clutch is caused by wear spots on your clutch basket. if you are careful they can be filed down just keep them straight this will restore a smooth clutch feel. to check progress slip a clutch disk in the basket all outer dogs of the clutch plate must contact basket at the same time good luck jim

Mar 15, 2009 | 1999 Yamaha TRX 850

1 Answer

Replacing clutch on honda cbr1000rr 07


should be opposite of the "drive chain,or shaft"side,it's a big cover!,check bikebandit.com for diagrams.

Jan 24, 2009 | 2007 Honda CBR 1000 RR Fireblade

Not finding what you are looking for?
1998 Honda CBR 1000 F Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...