Question about 2008 Suzuki GSX-R 600

1 Answer

2005 gxr 1000 getting no fuel to fuel rail no power to pump after crashed

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 188 Answers

Check all fuses

Posted on Aug 02, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Tryingn to find fuel pump shut off for a 2005 hyundia accent

pull the relay-- their is no fuel cutoff--fuel reset -or inertia switch on vehicle

Aug 02, 2016 | 2005 Hyundai Accent

1 Answer

Jaguar 2005 2l petrol loos power after few km switch of and restart than go fine and do the same after few km

This sounds like the fuel pump if you can get a gauge their is a connection on the fuel rail to check the pressure.

Dec 21, 2014 | 2005 Jaguar X-Type

1 Answer

When I changed the fuel pump and fuel pump relay it still won't come back on there is no power going to fuel pump for a 2000 Chevy impala what can the problem be?

There should be a "crash sensor" that shuts off fuel flow in the event of a crash. Likely that's been triggered or has gone bad.

Oct 26, 2014 | Spyder 2000-2005 Chevy Impala Dual CCFL...

1 Answer

Have just fitted new fuel pump and injectors to my 2006 ford transit van common rail however it ran for a short while and will not start fuel pressure at common rail

if you replaced pump ONLY and not the complete unit, I hope you didn't use the plastic clamp from the box.Many clamps just brake from the pressure and leaking. Corrosion on the connector will be a problem to,and finally the Ford CRASH SWITCH under the dashboard.
install fuel pressure gauge and crank the engine,if the gauge move 10-20 PSI is the connector. If no noise from the pump is electrical.Test power and ground on the pump connector and back trace the problem.crash switch,relay,fuse,ECM(alarm)flashing red light on instrument panel.if you key is the big one inspect the chip for lost or damage.
good luck

Oct 25, 2014 | Cars & Trucks

1 Answer

Where is fuel rail pressure sensor located 2005 ford focus

Before you change your fuel pump or fuel rail pressure or the sensors there are five things you will have to check first....first the inertia switch second if you have had the fuel filter change third the fuses fourth the sensors if they are bad or have been wet and the fifth the fuel pump pressure...

Dec 10, 2013 | 2005 Ford Focus

1 Answer

How to replace the fuel temperature sensor

fuel temperature sensors are used on return-less fuel systems and are usually mounted on the fuel rail, although on some vehicles it is integrated into the fuel pump. Those mounted on the fuel rail are easily replaceable but those integrated into the fuel pump requires replacement of the entire fuel pump. If you are getting a diagnostic trouble code between P0180 and P0189 then you have a fuel temperature sensor problem which, if it is integrated into the fuel pump it will require replacement of the entire fuel pump. On return-less fuel systems the fuel temperature sensor sends fuel density data to the PCM and then with that and data from the fuel rail pressure sensor the PCM commands the fuel pump driver module to adjust voltage to the fuel pump sufficient to achieve the proper fuel pressure.

Apr 19, 2011 | 2005 Kia Sedona

2 Answers

Please my 2005 xc90 is showing check engine with code P0087 Fuel rail pressure too low. The car will ran for a short period of time and then stalled out. What can I do ? Has anyone experience this before ?...

the fuel rail is the metal line hooked to the injectors that is fed by the fuel pump

now as for the code it set it can be caused by a weak fuel pump or a bad fuel regulator or a clogged fuel filter i would start by changing the fuel filter

Jan 27, 2011 | 2005 Volvo XC90

1 Answer

Wasn't getting juice to fuel pump ran a wire to fuse box wire is heating up but it worked fine for about a year pulled pump found the short and replaced wire new wire is heating up also. could i need...

Afellow ranger owener Ihave an 85 that iv,e had for 23 years but it has a mechical pump but i also have the factory manaul that covers the electric pump. According to the wireing diagramstarting at the fuel pump relay and working backto the pumps there are two pumps in this systen one is in the tank and a high pressure inline pump mounted to the frame rail. OK 37 yellow powers the relay from ignition switch comes out of relay as 787 PK/BK -H goes to a switch called a inertia switch and says opens at impact so i would think it brakes the currciut in a crash it has connection on bolth sides and is 37 Ythen turns back to 787 PK/BK -H Then goes to the in line pump witch is grounded by 57 BK 787 splits and runs to in tank pump this wire 787 PK/BK -H between the two pumps is sopposed to be a 1000 OMHS resistor wire goes through the motor witch grounds 57 BK and 29 Y/W come from the sending unit in tank and feed fuel gage

Dec 04, 2010 | 1986 Ford Ranger 2WD

1 Answer

I have 2005 gsx 1000 it dosent start is not passing gas the fuses are good and the fuel pum to can you help me

i would assume you hav ckd for sprkpurchase a spk plug tester 5bucks next ck fuel out of tank and filter etc is clear replace it use with great care starter fluid in airbox dont over do this high compersion motor wont take much let sit for min then try starting if bike kicks over your loosing fuel persure in rail i.e pump {may run insofficate presure or leaking injector [s]
or bad rail it self {highly unlikely} more the injectors remember 3 basics fuel air spark it runs

Jul 09, 2009 | 2005 Suzuki GSX-R 1000

2 Answers

Suzuki Gsxr 1000

check if there is power coming from the magneto and make sure all connections are connected

Jul 04, 2009 | 2005 Suzuki GSX-R 1000

Not finding what you are looking for?
2008 Suzuki GSX-R 600 Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

75817 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides