Question about 2011 Harley Davidson FLHX Street Glide
I'm not getting power to the lights on a 2014 HD Street Glide tour pack. Fuses in the block check ok. Would there be an inline fuse to the tour pack wire loom, and if so, where would I find it? The headlights and tail lights work fine. I must have burned a fuse because it was working before I swapped the loom connector between the bike and the tour pack. @
Hi, Ken for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at firstname.lastname@example.org. Good luck and have a wonderful day.
Side marker lights not working Harley Davidson Forums
2014 Harley Touring Service Manual pdf
2014 Harley Davidson Street Glide Owner Manual
Instant Tech Relief To speak to me personally for only a mere $6
Posted on May 18, 2018
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
check the wiring from the tailights back to the fuse panel, it sounds like an open connection. if i recall correctly check under the dash on the drivers side near the fuse panel for a bunch of wires in a bundle and look carefully for a wire or two that are cut/shorted/or seperated, you can also check under the drivers side kick panel by the hood release.
Posted on Feb 17, 2009
SOURCE: 2001 ford explorer sport trac
Just found the answer on another site. Sure enough went out removed the 3 philips head screws in the steering column opened it up and walla a wire connection had pulled itself free. When my son uses my truck he always uses the tilt steering, when I get in I have to readjust it. because of this the wire connection pulled itself out. I simply pushed it back in an blinker and brake light are now working. My husband is now trying to figure a way to secure the wire connection so it doesn't pull itself out again. Hope this helps others, either by saving the cost of a dealership or machanic or from getting rear ended.
Posted on Mar 21, 2009
Before going ahead and spending money on a new module, test it first. The module is located under the steering column. You'll find a Brown wire on one of the connectors (i just looked at a wire diagram). Do no disconnect anything. Back probe the brown wire, which is the power feed to your park lights. With the lights off, there should be 0 volts on you voltmeter. Turn the park lamps on, There should be 12V. If there is not 12V, disconnect the connector and try to check voltage at the pin that feeds to the brown wire, if still not 12V, replace the module. If you do get 12V, then module is ok, find where the 12v is being dropped before making it to the lamps.
Posted on Aug 09, 2009
No. All those lights are on the same fuse and are controlled by the headlamp switch.
Make sure that the fuses were all checked on the fuse panel inside the vehicle under the dash. That is where the fuse for those lights is.
Posted on Sep 13, 2009
Tips for a great answer:
Apr 24, 2018 | 2007 Harley Davidson FLHX Street Glide
Feb 24, 2018 | 2011 Harley Davidson FLHX Street Glide
Mar 23, 2014 | 2010 Harley Davidson FLHX Street Glide
Mar 29, 2013 | 2006 Harley Davidson FLHX Street Glide
May 16, 2012 | 2008 Harley Davidson FLHX Street Glide
Apr 24, 2012 | 2011 Harley Davidson FLHX Street Glide
Mar 14, 2012 | 2008 Harley Davidson FLHX Street Glide
Mar 12, 2010 | 2008 Harley Davidson FLHX Street Glide
343 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: