Question about Honda Fusion Motorcycles

1 Answer

I cant't start my wave 125cc this light on the meter but once i hit the electric start button everything goes off and we i release the e start button everything go on again.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Your battery is most likely very flat, it has enough power to run your lights but not enought to turn over your engine to start it. Best thing to do is try to bump start it if the bike is a manual, put the bike into 2nd or third gear down a hill, get the bike rolling with the clutch in and let the clutch out when you get to good rolling speed. the bike will **** into life. Let the bike run for a good 20 mins. Battery should be recharged enough to start the bike again.
If the bike is an automatic you will have to use a battery charger.

Posted on Aug 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced battery now nothing works,doors dont unlock,car doesnt start,no sounds when pressing buttons although it still sang when battery replaced,pressed "P" button hoping it would do something and now it...


The waves mean that the remote is vibrate mode. Try reprogramming the remote. Open the door, turn ignition on, press and release the valet button once then, press and hold the valet button. press the lock button on the remote. Vehicle should respond with a chirp from the siren. Release valet button, turn off ignition, test system.

Jan 17, 2014 | Directed Electronics 479V Remote Gen 2...

1 Answer

Start problem?


Let me briefly explain what happens when you turn n the key. All power is off in the off position with the possible exception of the brake light. When you turn on the key, you supply power from the battery to the electrical system. Typically, all systems are powered through a connection on the start solenoid. When key is on and the solenoid is in the off (or rest) position - all electrical works. When you energize the start solenoid, you need all the power you can get to run the starter - everything electrical turns off. After the start, you release the start button, everything electrical comes back on (solenoid returns to the rest position).
In your case, you say everything goes dead when you press the start button - this is as it should be - however, the mechanics of this system should deliver power to the starter - which evidently it is not. (A solenoid is nothing more than a electric powered heavy duty switch) It is possible your solenoid is worn out. There is heavy sparking/burning of the contacts every time you press the button. First thing to do is check voltage on the start side of the solenoid when you press the button. Voltage should be the same as on the hot side with the key on. Other possibilities - the wire from the solenoid is loose, damaged or disconnected, check both ends for tightness and cleanliness. There is that possibility there is a problem with your starter. Removal is not for the faint of heart though it is possible. There is also that possibility your engine is locked up and your starter can not turn it over because of that. If this is the case and you have a amp meter - you will see heavy draw on the starter wire. If you have a volt/ohm meter, you can so all the prelim checking.
I hope this helps you with your trouble. Good luck and thanks for using FixYa.com

Jul 29, 2013 | 1995 Suzuki VS 1400 Intruder

1 Answer

Our dryer doesn't stay on when you hit the start button. It turns off when you release the button.


The seal in ccircuit for run usually goes through a switch in the motor, whitch if it sticks or the switch goes bad, it wont stay running.

Aug 29, 2011 | Kenmore Elite Oasis 6808 Electric Dryer

1 Answer

I set up my own wireless network and now my printer will not communicate with my laptop.WIFI light flashes red. Have tried everything to reconnect. Lexmark Z2420.


I suggest you reset the Lexmark Z2420 wireless network adapter. To reset, do the following: With the printer on, press and release the power button. The printer will enter power save mode. Now, press and hold the paper feed button. While holding down the paper feed button, press and release the power button. Continue holding the paper feed button for 30 seconds. Release the paper feed button. This will reset the internal network adapter (INA). When the printer has been reset, a solid orange Wi-Fi indicator light should appear. If Wi-Fi light goes back to flashing red, you have not successfully reset the printer. Start the procedure again. Once you have a solid orange Wi-Fi light, reconfigure the printer for wireless connection. Thanks.

Jul 29, 2010 | Lexmark Z2420 Printer

1 Answer

My antenna light stays on even after I have realeased the mike


Try checking the SWR's on channel 1, 20, and 40. The SWR's will change from the low channels to the mid channels to the high channels. The key is to make sure that the SWR's are around 1 or less at all three points. If the light goes out when checking one of them, then the problem is most likely the SWR's. If the light stays on when checking these channels, the issue might still be the SWR's but I would look at the grounding on the antennas. When holding the talk button on the mic and switching from calibrate to swr, can give a false reading. This is due to the calibrate circuit remaining open until you release the talk button. Take the SWR reading by releasing the Talk button on the mic after calibrating then pressing the talk button again after switching back to SWR. This will be the most accurate reading. From everything you described, I would be looking for a grounding problem with the antennas or coax, possibly even a rub though on the coax somewhere in the dash.

Dec 20, 2009 | Cobra 29 WX NW ST 40-Channels Base CB...

1 Answer

Lights Blink washer wont start


Check user manual for programme reset , but poss. hold start button on for minute or try same with cancel button.

Nov 02, 2009 | Washing Machines

2 Answers

Whirlpool 110 electric dryer will not keep running


When you press the start button you complete a circuit bringing the juice into your dryer to run the motor the igniter or heating elements and what ever else goes whee when your dryer is drying. So if you press the button to complete the circuit then when you let go of the button it would stand to reason that it break that flow and shut it all down. However in a dryer there is something of a centrifugal switch that kicks in and keeps that circuit open and flowing with juice once the drum begins to turn and you let go of the button. That's why in a normal situation if you don't hold the button down long enough the dryer will cut right back off or if you open the door to the dryer to throw something in and close it before it quits turning it will stay running. Sounds like you could add this centrifugal switch to the list of possible culprits in this mystery. O7OUT

Jun 06, 2009 | Whirlpool LER4634J Electric Dryer

2 Answers

I have a bose wave model awrc-1g cant set time from military time to regular


Hold the alarm setup button and at the same time hit the on/off button.

Oct 16, 2008 | Bose Wave Radio

5 Answers

My Maytag dryer won't start when I hit the start button


My dryer light comes on for my Maytag SDE4606AYW dryer when you open the door and I can hear the timer clicking but when I hit start the motor doesn't even attempt to start but there is obviously power. My dad just installed a new power cord to the dryer but this is a seperate issue as we were obviously unable to check the motor before we got a cord for it. He has years of electrical experience so I'm assuming he connected the new cord right. Any ideas on fuses in the dryer or why it may not be getting power?

Jan 15, 2008 | Maytag PYE2300AY Electric Dryer

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...