Question about 2005 Yamaha YZF-R6

1 Answer

On tick over little ratle not at high revs - 2005 Yamaha YZF-R6

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 221 Answers

You mean kick over? more than likely it is your vavle train either needs adjustment or you may have cam play or just not enough lube on start-up

Posted on Aug 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 sable is ticing but full of oil


A little valve tick is normal on older cars. Does the ticking get louder as you rev the engine, or does it go away? If it gets louder, you may have a stuck rod and should get it serviced asap. If it goes away, nothing to worry about.

Apr 28, 2015 | Cars & Trucks

2 Answers

I have a 04 mustang 3.9 v6 and every time I start it, its rev a little high and makes a loud ticking noise but after a few seconds it idols down and the ticking goes away why is that?


Fords do rev high when first started but a breather filter may be dirty,the ticking is probably the valves that haven't gotten oil pressure to them.If it has high miles you may want to use a full synthetic with your next oil change so the valves will be safer from start up wear.I personally use Slik 50 and Quaker State Synthetic Blend...

Jun 18, 2012 | Cars & Trucks

1 Answer

Focus revs high when changing gear


I assume this is manual gearbox? if so you need to replace the clutch.

Jun 12, 2012 | 2000 Ford Focus

1 Answer

What should the H, L, and T settings be on on a husqvarna 51 chainsaw?


the "H" is the high rev setting the "L" is the low or tick over setting and there set up when the engine is hot and running,,,first the high rev ste up tweek the screw till the engine is running at full revs then tweek the low revv till the engine will stay ticking over,,,

Nov 28, 2010 | Husqvarna Garden

1 Answer

I have a 2009 Sym Symply/Orbit and when I went over a speed bump, my engine loses all power. When I rev it up, it revs up a little and then reduces revs to tick-over speed, then revs up again then reduces...


Try cleaning your carb, it might have a small blockage stopping the petrol flow, you can buy carb cleaner from your local dealership, it willr emove all dirt from your carb :)

Aug 01, 2010 | Sym Husky 125 Motorcycles

1 Answer

Zx6r erratic throttle


Just check on your air ducts. When the bike is staionery it will idle rev and even run well on the dyno, but on the open road the airducts must be in and instadled or mounted correctly

Jun 15, 2010 | 1997 kawasaki ZX-6R Ninja

1 Answer

What aere the primary settings on the high & low speed screws on a sears 42cc chain saw engine?


start off with the low speed screw turn it right in then undo it 1+1/2 a turn start saw up and screw slow running screw in or out a little bit at a time till the saw ticks over,,then give the saw full throtel and screw the fast screw in or out till the saw is reving as fast as it will rev at

Mar 25, 2010 | Garden

1 Answer

Ticking noise and general engine noise after burnouts...


If he was doing burnouts it could be multiple problems - overheating, too many revs, drivetrain hammered.
Certainly a lot of burnouts can cause overheating - no air and lots of revs gets things hot really fast!
High revs can result in camchain issues, piston/valves coming together, broken rings, siezed pistons, broken bearings, and much more :)
Sorry to hear this - I suggest a trip to a bike mechanic to get a diagnosis before it gets worse and costs you a packet.

Jun 28, 2009 | 2008 Honda CBR 600 RR

Not finding what you are looking for?
2005 Yamaha YZF-R6 Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...