Question about kawasaki KX 250 Motorcycles

1 Answer

I had to replase the piston and fogot how to put it back togther

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Put the piston in with the mark on the top of the piston facing the exhaust port of the cylinder. put one circlip in the piston in the bore seated correctly in the groove. place piston over rod facing correct direction and insert wristpin into piston and through the rod needle bearing in the top of the rod. insert other circlip and seat correctly in groove. install compression rings with letter or any markings facing up. markings usually located at end gap on either side. install oil ring with straight ring on top squiggly ring in center and straight ring on bottom all in the same groove which will be the lowest groove on the piston.stagger all the ring end gaps. do not let all the gaps line up. install base gasket on engine case. clean everything and make sure everything stays clean. slide cylinder over piston and compress rings with fingers and finesse cylinder over piston. do not force. put nuts on studs and tighten to spec in service manual. install head gasket correctly and put head on and put nuts on studs. tighten to spec. reassemble rest of motorcycle and get hurt! have fun

Posted on Jul 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Presure test the radiator 1999 chrysler 300 can not find water leak, replased water pump


it very well could be a blown head gasket and its leaking into the piston

Dec 05, 2012 | 1999 Chrysler 300M

1 Answer

21hp intek engine one cyclinder smoking badly when going up hill


It either has a scored cylinder and piston or a broken piston oil control ring or both

Nov 07, 2012 | Cars & Trucks

1 Answer

How to slacken rear brake shoes to replase disc


Hi Ricky

Your car has disc brakes so you need to release the brake pads not shoes (they are for drum brakes). That should help when you buy a new set.

Loosen the split pins which hold the pads in the caliper. You should then be able to push the pads out. It sounds like the pads are worn down so much that the caliper pistons are at their full reach.

Once you have slid them out, you need a piston retractor tool to push the pistons back in the caliper in order to be able to fit the new pads.

SLide the pads in, use copper grease on the back surface to stop them squeaking. Once done, pump the brake pedal to set the pads and the job is finished.

Aug 21, 2010 | 1994 Saab 900

1 Answer

I took out the back cover to replase the cell cant put back lid help watch #355less


You will probably need a watch press to get the back on. Call around at your local jewelers as they will have one if they carry watches.

Aug 20, 2010 | Skagen Watches

2 Answers

I can't put mt paslode finish nailer back together again


go to Paslode.com and you can download a manual that shows the spring. It sits in a recess under the follower that pushes the nails

Jul 20, 2009 | RTO PasLode 900420 Impulse Framing Nailer

2 Answers

I need picture step by step instructions of how to put my mr. heater back togther.


here is the web site for mr heater,they have parts break downs to down load....
www.pinnacleint.com

Feb 24, 2009 | Heating & Cooling

1 Answer

I PUT ENGINE CLEANER IN 2YEARS AGO OIL GAGE DROPS ..


v-8 with high miles will do that due the worn piston rings. I would use a bottle of smoke-away and maybe use lucas oil stablazier or go all out and use 10-40

Feb 11, 2009 | 1994 Chevrolet Suburban

1 Answer

Torque settings for holden 308


see if this site helps you.

http://www.boxwrench.net/specs_index.htm

Nov 12, 2008 | 1998 GMC Blazer

1 Answer

My Ipod Video 30Gb Black Won't Charge


someone possibly opened it because they are hard to take apart it might need a new battery

Sep 01, 2008 | Apple iPod MA446LL/A MP3 Player

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

408 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...