Question about 1997 Honda CBR 600 F(3)V

2 Answers

I have a 1996 Honda CBR 600F3. Bike ran fine for the past 3 months. I now have a problem. The problem is that the bike runs for about 10 minutes and then stalls shuts off. It almost seems as though I'm out of gas. I checked the on/off valve for the fuel it was to the on position. I have also checked fuel flow from gas tank. Fuel flow is good from gas tank. I also checked fuel filter. Gas flows from fuel filter good also. Electrical seems to be normal 14.98VDC @ 2000 RPMs.

Posted by on

  • 1 more comment 
  • Brian Aug 04, 2009

    I checked the battery with everything off. VM reads 12.98VDC. With the bike running @2000RPM voltage is 14.89VDC. My battery is new from May 2008. I also bring the battery indoors for the winter.

    I removed the main air filter. Bike seems to run normal without shutting off. I will keep you updated on my progress.

  • Brian Aug 04, 2009

    Yes it seems as though it's a fuel issue. When I first encountered the problem I thought I ran out of gas. The problem was identical as when your out of gas. But when I tried to restart the bike it would only run for about 5-10min and then shut off. I've been able to take the bike for a few test rides for about 30min or so after installing a new air filter. But I'm afraid to go to far.

  • Paul Blessing May 11, 2010

    Battery is suspect here. Put voltmeter across battery with everything off-should be about 13vdc-now turn on the key with your headlight on and read battery?



2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 188 Answers

If all cylinders die at the same time should be fuel or electrical?

Posted on Aug 04, 2009

  • Paul Blessing Aug 04, 2009

    Had a person with a bad petcock(diaphragm) the other day?


  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

How long ago did you check the engine valves clerance ? if longer than 30000km ago it can be the problem...sorry for my's weak

Posted on Jul 28, 2009


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 96 CBR 600F3 runs for approx 10Min then stalls out.

got a 2002 cbr 600 fuel not getting thought to injetters

Posted on Sep 20, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Put a new battery in my 96 cbr 600 last month its been fine .. yesterday did a few wheelies n the key came out finally wen i stoped the bike died n battery was dead ... could it b a stator or rectifier ?...

chare the battery back up and get a volt meter, the battery should read 12v or a little higher, when you start the bike the voltage should rise to around 14v, if it doesnt rise it is not charging and the reg or stator needs checking

Jun 01, 2011 | 1996 Honda CBR 600 F(3)T

1 Answer

Hi there,i have a honda cbr 600f (1995) with a 3 month old battery,i left the bike for two and 1/2 weeks without starting it,the bike started on 1st first time, went for a long ride(60 miles).Stopped for a...

sir,there are 2 reason
1. please check bolts of small fuse connecter near the battery ,sometimes it get loose ,ectually that is main positive connecter to battery
2.please replug the rectifier-regulater cuplers ,otherwise you need to replace the regulater

Apr 27, 2011 | 1996 Honda CBR 600 F(3)T

3 Answers

I just bought a used 2002 honda cbr 954 rr. i cleaned the spark plugs about a month ago and it started up and ran fine. but now i cant get it to run no longer than a few seconds. any ideas what the problem...

Was the bike running fine before you cleaned them? If your bike won't stay running, you might need to adjust your idle. There is a black round dial on the left side next to the stator (big round circular housing) turn it so the fuel is increased.

Jan 11, 2010 | 2002 Honda CBR 954 RR Fireblade

2 Answers

96 CBR 600F3 runs for approx 10Min then stalls out.

Check the vacuum pipe from the carbs to the fuel tap, if its gat a pin hole in as you demand more fuel the vacuum loss cuts downthe fuel flow and the bike will stop!

Jul 28, 2009 | 1997 Honda CBR 600 F(3)V

1 Answer

954 fireblade splutters at 7000 rpm

1ST of all i think you should take your bike to another dealer to get it fixed as they should be able / confident mechanics to repair any problem.
But anyway have you checked the throttle position sensor ? of the fuel injector connections ?
just that water could of coroded the connectors.

Jun 21, 2009 | 2003 Honda CBR 954 RR Fireblade

1 Answer

Honda cbr 400 rr starting problem

i could not find a schematic of a 96 cbr400rr, so guessing this bike is not from the USA. however, there should be a master fuse near the battery on the positive side mounted to the battery box somewhere. i would check this fuse first to see if its burned out.

also, is battery fully charged? might have to top charge the battery to get good juice if its old (>3 years) and been sitting for a bit.

good luck.

Jan 28, 2009 | 1996 Honda CBR 400 RR

1 Answer

97' cbr 600 rr f3 doesn't start

check to see if fuel switch is on...when was the last time carbs were checked?

Dec 24, 2008 | 1997 Honda CBR 600 F(3)V

1 Answer

How do I adjust the rear tire on a 97 honda cbr 600f3

40mm slack up and down middle of chain. not tight when sitting on bike. loosen axle ajust both sides evenly, retighten axle install new split pin

Dec 04, 2008 | 1997 Honda CBR 600 F(3)V

1 Answer

Fuel pump pressure

In my experiences over the years pressure testing the carbs and messing with the fuel pump, I have never actually tested the pump output. Knowing that the average pop off pressure of the float valve on the float is 10-13 psi, this being tested via hand held pressure gauge to ensure no leaks before installation on the bike. I assume that the fuel pressure coming from the pump should not exceed the pop off pressure or it could cause the carbs to leak though and the bike would run rich. Hope this helps out.

Nov 10, 2008 | 1997 Honda CBR 600 F(3)V

Not finding what you are looking for?
1997 Honda CBR 600 F(3)V Logo

Related Topics:

406 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

76691 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides