Question about 1995 Yamaha FZR 1000

2 Answers

Engine wont turn over when start button is pushed and if i jump the starter relay the engine turns over but has no spark. i have replaced the relay assembly and still have the same problem. the bike is a 1995 Yamaha FZR 1000.

Posted by on

  • swarriner Jul 30, 2009

    Ive replaced the stop start switch cluster.and still have the same problem.The bike was laid down a year ago and hasnt ran since.

  • swarriner Aug 01, 2009

    ok ive checked the wiring and everything seems to be intact.i can here the fuel pump turn on when the key and the switch are on but when you push the start button nothing happens.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I posted a question bout my 93 almost the same prob i added a push button directly to selinoid an now mine start but i gotta use both buttons to start it. but just using one button i get no spark

Posted on Apr 11, 2012

Ad
  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 13 Answers

Starter button. The only problem with that is you'll have to replace the whole combo with the run-stop,starter switches, etc;...

Posted on Jul 27, 2009

  • cabrooksjr
    cabrooksjr Jul 30, 2009

    You said you can if you run it straight to the starter you can get it to turn over. Check your wiring to see if in the fall were any wires stripped or broken.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1994 Nissan pickup 2400 2.4L manual trans I can push start but wont start by key replaced starter and starter relay get clicking sound out of starter relay but will not turn over


Check all connections and cables for corrosion. Make sure there is a good engine to chassis ground. You are loosing connection somewhere.

Dec 20, 2016 | Nissan Cars & Trucks

2 Answers

Wont start it cranks but nothing happens.wont turn over. put a new what you would call distributor. still nothing.


If the Starter isn't turning the engine over, but you hear a clicking sound, you may have a bad Starter.
If the Starter is turning the engine over, but you are getting no Spark, you may have a failed Camshaft or Crankshaft Position Sensor, or your Timing Belt may have jumped or broken(common on the neons).
If the Starter is turning the engine over, but you are getting Spark, you may have a failed fuel pump, fuel pump relay, or fuel pressure regulator.

Before you start replacing sensor, double check the Timing belt to ensure it hasn't broken or jumped, and check to see if you are getting a spark or not.

Mar 12, 2011 | 2003 Dodge Neon

2 Answers

I drove my 1999 accord EX to work & 8 hrs. later I tried to start it and it did nothing. Tried jumping still nothing. Put new battery on and it still did nothing.What is the problem?


Hi, diagnosing a no-start condition requires a logical approach to figuring out what might be preventing your car from starting. First, if the engine won't even crank over when you turn the ignition to START, your car obviously won't start.
When you turn the ignition key to start your car, voltage from the battery flows through the ignition switch to the Park/Neutral safety switch and/or brake pedal or clutch pedal safety switch (you have to push the pedal down before the circuit will complete) to the starter relay or solenoid. When the relay or solenoid is energized by voltage from the ignition switch circuit, it closes a contact that routes more power from the battery directly to the starter to crank the engine. The starter motor spins, pushes the starter drive gear to engage the flywheel and cranks the engine.

If the engine fails to crank, there is a fault in one of the components in the battery/ignition/starter circuit.

Ten Reasons why you car won't start..
  1. Low battery (Check battery voltage, recharge if low, or jump start with another vehicle or battery charger).
  2. Loose or corroded battery cables (Inspect, clean and tighten BOTH ends of BOTH battery cables).
  3. Bad starter relay wiring connections or ground connection (Inspect, clean, tighten wiring connections).
  4. Bad starter relay/solenoid (Check for voltage at relay, if relay has voltage but there is no "click" when key is turned to start, replace relay).
  5. Bad starter (Jump battery voltage direct to starter to see if it spins, or remove starter and have it bench tested at auto parts store).
  6. Damaged starter drive or teeth on flywheel (Remove starter and inspect drive gear and flywheel teeth, replace damaged parts if necessary).
  7. Bad ignition switch (Check to see if voltage reaches starter relay/solenoid when turn to start. If not, check for open P/N switch and brake or clutch pedal switch. Replace ignition switch if defective).
  8. Open P/N safety switch, or open Brake Pedal Safety Switch (automatic transmission) or open Clutch Pedal Switch (manual transmission). Bypass switch with jumper wire to see if engine cranks, or use test light or voltmeter to check for voltage passing through switch when ignition is turned to start.
  9. Engine seized due to bearing failure or internal damage (Use socket and long handle to see if engine can be turned by hand, if not engine is locked up).
  10. Engine hydrolocked due to coolant leak from leaky head gasket (Use socket and wrench to see if engine rotates, remove spark plugs and see if coolant comes out or engine can not be cranked with plugs out).

Hope it helps identify and solve the problem

Jan 16, 2011 | 1999 Honda Accord

1 Answer

I have a 2003 Saturan Ion that won't start


Hi, this is what you should do when your car won't start. Diagnosing a no-start condition requires a logical approach to figuring out what might be preventing your car from starting. First, if the engine won't even crank over when you turn the ignition to START, your car obviously won't start.
When you turn the ignition key to start your car, voltage from the battery flows through the ignition switch to the Park/Neutral safety switch and/or brake pedal or clutch pedal safety switch (you have to push the pedal down before the circuit will complete) to the starter relay or solenoid. When the relay or solenoid is energized by voltage from the ignition switch circuit, it closes a contact that routes more power from the battery directly to the starter to crank the engine. The starter motor spins, pushes the starter drive gear to engage the flywheel and cranks the engine.

If the engine fails to crank, there is a fault in one of the components in the battery/ignition/starter circuit. Check it out.....
  • Low battery (Check battery voltage, recharge if low, or jump start with another vehicle or battery charger).
  • Loose or corroded battery cables (Inspect, clean and tighten BOTH ends of BOTH battery cables).
  • Bad starter relay wiring connections or ground connection (Inspect, clean, tighten wiring connections).
  • Bad starter relay/solenoid (Check for voltage at relay, if relay has voltage but there is no "click" when key is turned to start, replace relay).
  • Bad starter (Jump battery voltage direct to starter to see if it spins, or remove starter and have it bench tested at auto parts store).
  • Damaged starter drive or teeth on flywheel (Remove starter and inspect drive gear and flywheel teeth, replace damaged parts if necessary).
  • Bad ignition switch (Check to see if voltage reaches starter relay/solenoid when turn to start. If not, check for open P/N switch and brake or clutch pedal switch. Replace ignition switch if defective).
  • Open P/N safety switch, or open Brake Pedal Safety Switch (automatic transmission) or open Clutch Pedal Switch (manual transmission). Bypass switch with jumper wire to see if engine cranks, or use test light or voltmeter to check for voltage passing through switch when ignition is turned to start.
  • Engine seized due to bearing failure or internal damage (Use socket and long handle to see if engine can be turned by hand, if not engine is locked up).
  • Engine hydrolocked due to coolant leak from leaky head gasket (Use socket and wrench to see if engine rotates, remove spark plugs and see if coolant comes out or engine can not be cranked with plugs out).

Dec 02, 2010 | 2003 Saturn ION

1 Answer

I have a 1997 grand prix. Most days it starts. once in a while it will not start. You can sometimes rock key back and forth quickly and it will catch. But most of the time odly enough wait over night and...


When you turn the ignition key to start your car, voltage from the battery flows through the ignition switch to the Park/Neutral safety switch and/or brake pedal or clutch pedal safety switch (you have to push the pedal down before the circuit will complete) to the starter relay or solenoid. When the relay or solenoid is energized by voltage from the ignition switch circuit, it closes a contact that routes more power from the battery directly to the starter to crank the engine. The starter motor spins, pushes the starter drive gear to engage the flywheel and cranks the engine.

Low battery (Check battery voltage, recharge if low, or jump start with another vehicle or battery charger).
Loose or corroded battery cables (Inspect, clean and tighten BOTH ends of BOTH battery cables).
Bad starter relay wiring connections or ground connection (Inspect, clean, tighten wiring connections).
Bad starter relay/solenoid (Check for voltage at relay, if relay has voltage but there is no "click" when key is turned to start, replace relay).
Bad starter (Jump battery voltage direct to starter to see if it spins, or remove starter and have it bench tested at auto parts store).
Damaged starter drive or teeth on flywheel (Remove starter and inspect drive gear and flywheel teeth, replace damaged parts if necessary).
Bad ignition switch (Check to see if voltage reaches starter relay/solenoid when turn to start. If not, check for open P/N switch and brake or clutch pedal switch. Replace ignition switch if defective).
Open P/N safety switch, or open Brake Pedal Safety Switch (automatic transmission) or open Clutch Pedal Switch (manual transmission). Bypass switch with jumper wire to see if engine cranks, or use test light or voltmeter to check for voltage passing through switch when ignition is turned to start.
Engine seized due to bearing failure or internal damage (Use socket and long handle to see if engine can be turned by hand, if not engine is locked up).
Engine hydrolocked due to coolant leak from leaky head gasket (Use socket and wrench to see if engine rotates, remove spark plugs and see if coolant comes out or engine can not be cranked with plugs out).

Jul 14, 2010 | 1997 Pontiac Grand Prix

1 Answer

My car does not start or turn over. The radio works and so does the fan.


When you turn the ignition key to start your car, voltage from the battery flows through the ignition switch to the Park/Neutral safety switch and/or brake pedal or clutch pedal safety switch (you have to push the pedal down before the circuit will complete) to the starter relay or solenoid. When the relay or solenoid is energized by voltage from the ignition switch circuit, it closes a contact that routes more power from the battery directly to the starter to crank the engine. The starter motor spins, pushes the starter drive gear to engage the flywheel and cranks the engine.

Low battery (Check battery voltage, recharge if low, or jump start with another vehicle or battery charger).
Loose or corroded battery cables (Inspect, clean and tighten BOTH ends of BOTH battery cables).
Bad starter relay wiring connections or ground connection (Inspect, clean, tighten wiring connections).
Bad starter relay/solenoid (Check for voltage at relay, if relay has voltage but there is no "click" when key is turned to start, replace relay).
Bad starter (Jump battery voltage direct to starter to see if it spins, or remove starter and have it bench tested at auto parts store).
Damaged starter drive or teeth on flywheel (Remove starter and inspect drive gear and flywheel teeth, replace damaged parts if necessary).
Bad ignition switch (Check to see if voltage reaches starter relay/solenoid when turn to start. If not, check for open P/N switch and brake or clutch pedal switch. Replace ignition switch if defective).
Open P/N safety switch, or open Brake Pedal Safety Switch (automatic transmission) or open Clutch Pedal Switch (manual transmission). Bypass switch with jumper wire to see if engine cranks, or use test light or voltmeter to check for voltage passing through switch when ignition is turned to start.
Engine seized due to bearing failure or internal damage (Use socket and long handle to see if engine can be turned by hand, if not engine is locked up).
Engine hydrolocked due to coolant leak from leaky head gasket (Use socket and wrench to see if engine rotates, remove spark plugs and see if coolant comes out or engine can not be cranked with plugs out).

Jul 14, 2010 | 1995 Suzuki Sidekick

2 Answers

Engine will not turn over. lights, horn, everything else works, no clicks, no nothing, but it will not turn over.


You're describing a no rotation issue and not a no start issue correct? If you dont hear/feel the starter relay clicking, it eliminates everything in the circuit to that point meaning the ignition switch, Transmission Range Sensor (TRS) (you don't have a neutral start switch unless you have a rare manual transmission), ground input from the Powertrain Control Module (PCM) to the starter relay coil, and starter relay are good. Based on what you've said that leaves the primary battery cable from the battery to the starter, and the wire from the starter relay to the starter solenoid contact on the starter. Have you checked their continuity? One more voltage to check at contact 30 (input volts from battery to starter relay contacts) on the starter relay socket. Should see 12vdc all the time.

You should check the battery. The true test is a load test. Does jumping the battery using jumper cables make any difference? If it starts, change the battery. I take it to check the starter you jumpered the solenoid contact on the starter to the battery correct? Have you tried wiggling the battery cables as you turn the key? They can corrode and fail internally. Are the engine and chassy ground connections clean and tight?

Jul 14, 2010 | 2004 Dodge Caravan

1 Answer

Coils wont fire,and hit start button and wont turn over,can jump starter relay and will turn over


Try putting power to the small red on relay, this actuates the solenoid, if power now goes to starter its OK (if not replace). Then check the Start Button contacts are good - check for continuity across it - & all interlocks (neutral / clutch & side-stand switches) work OK. Also check for continuity between the start button & starter relay + from relay to solenoid

Ride safe
Bike-Doc
Please mark this as very helpful (if it has been!!)

Apr 22, 2010 | 1993 Suzuki GSX 600 F (Katana)

2 Answers

I have changed the battery the relay abd rebuilt the solenoid and it still wont start , the starter has been bench tested and it came out good , all it does is make the relay click


You seam to have done most checks,but you dont mention checking the fuses,allso make sure your earth wire from the battery is making a good contact. are you positive the engine turns over, try putting it in first and push starting it with the spark plugs removed the rear wheel should turn quite easily.

Mar 12, 2010 | 2003 Harley Davidson FLHTC Electra Glide...

2 Answers

95 jeep cherokee country 6 cyl auto. wont crank all the time


Bad solenoid i would guess. Not making a connection there. Any basic wiring and ignition switch problems should be alleviated by jumping the starter with a screwdriver. I would check the solenoid and starter brushes

Dec 30, 2009 | 1994 Jeep Cherokee Country

Not finding what you are looking for?
1995 Yamaha FZR 1000 Logo

494 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...