Question about 1990 kawasaki ZXR 750

1 Answer

My name is "william" i have a 98 ninja 750. the idle gos to high or to low and it kills it i trid turning the nob to set it and it will set good on about 1200 rpm but if u hit the gas it go to about 4000 rpms and it want come down so i turned the nob down and the it gos down to about 2000 rpms and then it idle down then its to low. if u can help me that would be good thnks william

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

The carbs need balancing!

Posted on Aug 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 kia sportage will brake lit switch cau the truck stall whil driving


Yes, If your idle RPM is too low it can kill the engine due to the high current of the brake lights will cause a stall.

Most cars use an RPM idle of 750 to 775 RPM. Check your manual then increase your idle a little.
Hope this helps.

Mar 23, 2015 | 2001 Kia Sportage

1 Answer

Wont shift from nutral in to gear while running


Often, it mean that the clutch stay engage.
Now the question can be, is the idle to high for the clutch to disengage while at idle? you might try to reduce the idle speed by turning eather the nob on carburator or the ajustement on the cable.

then if the idle is very low and the clutch still engage (that is why you can not shift) you migh want to check at the clutch and see if it is not stuck.

Nov 07, 2013 | RTO 125cc Full Size Adult Quad ATV

1 Answer

Idle problem integra


check the MAP sensor (manifold absolute pressure). The ECM (car computer) uses that to keep idle at minimum 750 RPM. It's normal for it to run high when cold. These small 4 banger motors typically run hot, and they won't run right IF they're NOT running hot, ergo the idle is usually high when it is cold so as to cause it to warm up quicker. If the RPM's drop below 750, suspect the MAP sensor, &/or ECM.

Apr 18, 2013 | 1995 Acura Integra Coupe

1 Answer

How do I adjust the carburator on a craftsman blower


All carburetors have 3 screws high and low and idle, then screw high and low all the way in, then turn them back 1 and half that should be factory settings go from there. start with the high idle back it out slow until it sounds good. My blower ran good on two turns out on high idle then three turns on low idle. Good luck...

Sep 15, 2012 | Craftsman Garden

1 Answer

91 ninja 750 no spark, but got power in and out of both coils...? ignitor box


I PRESUME YOU WERE CRANKING THE MOTOR WHEN YOU TESTED FOR VOLTAGE AT THE COILS? HAVE YOU CHECKED KILL SWITCHES AT SIDE STAND AND HANDLEBARS FIRSTLY?

Jan 29, 2012 | kawasaki Kawasaki Zx750j1 Ninja Zx7...

1 Answer

Swapped a 99 kawasaki ninja EX250 motor for a 1998 kawasaki ninja EX250 motor now wont start


sounds like you have a carb problem Jason,possibly probably your float level is set too low not allowing sufficient fuel to Venturi

Nov 27, 2011 | kawasaki Ex250f8 Ninja 250r Motorcycle...

1 Answer

Kawasaki Ninja 250 running problem


This could be due to timing screw being incorrectly set
Locate gold timing screw on the carbrettta turn it clockwise only slightly till bike idles without choke on, Then when choke it on it should idle a touch higher.

Jun 21, 2010 | 2008 kawasaki Ninja 250R

1 Answer

1964 5 1/2 hp evinrude kills at high speed


You should have a High Speed carb adjust and a Low Speed carb adjust. If it's running fine while idling, adjust the high speed setting. If you have two nobs, its the lower one. May be set wrong. If you don't have two nobs, remove the carburator and check the jets to make sure they are completely clean or better yet, order yourself a carb rebuild kit to take care of all of this. I just rebuilt my 1971 evinrude 4hp and the carb kit made the world of difference.

Apr 17, 2010 | Light Outboard Motor Boat Bass Fishing...

1 Answer

I lost the paper behind the nobs and I dont know what the different switch spots represent


Just turn the unit on and check the functions. You should have high and low fan only settings, off , then high and low cool settings

Jul 28, 2009 | Kenmore 72055 Air Conditioner

Not finding what you are looking for?
1990 kawasaki ZXR 750 Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...