Question about Motorcycles

1 Answer

Do you have a diagram of the float . The carb # 27521049

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Motorcycles Master
  • 40,748 Answers

Hi, William I would really love to help you but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my mental telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on the word "COMMENT" below and provide this information in the box that will open and then click on the green comment box in the bottom right-hand corner after it posts I will receive an "ALERT" icon that will allow me to respond to your information.
Good luck and have a wonderful day.

Posted on May 10, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Carburetor diagram marvel schebler


wot is the problem with the carb , they are very easy to rebuild !? place all bits on white paper , clean all parts and blow out the jets and all dirt in the carb and check the float needle is clean and no grooves on the tip and moves freely in place ! put floats in a bowl of fuel and make sure the float ! slowly re fit all parts , float level is approx flat wen carb is held upside down ! re fit and fuel up and hope you have fun ! P...

Nov 27, 2013 | Motorcycles

2 Answers

Diagram for carb on 350 bruin


Hi, Anonymous and the usual suspects are:
1. Damaged or restricted fuel tank venting system.
2. Loose float bowl screws.
3. Damaged float bowl o-ring.
4. improper fuel level in the float bowl.
5. Worn or dirty inlet valve or seat.
6. Damaged or leaking float assembly.
7. Particle contamination in inlet fitting cavity.
Good luck and have a nice day.

Feb 13, 2013 | Yamaha 2005 Bruin 350 Auto 4x4

1 Answer

Why does my Honda xr leak gas out of the overflow


The float in the bottom of the carb is either slightly out of position or there is a bit of trash at the float needle preventing the float from closing off the gas flow. Clean the carb. Generic diagram below. tombones49_245.gif

Aug 18, 2011 | 2002 Honda XR 200

1 Answer

BIKE WONT START FUEL STUCK IN FUEL INLET OF CARBURETOR


The float is stuck in the closed position. Remove the float bowl on the bottom of the carb and spray carb cleaner at th float needle. Gently lift the float upward then let it drop. Repeat this several times until the fuel flows when the float is dropped and stops when the float us lifted upward. Please rate my answer. Thanks! Below is a generic diagram. tombones49_13.gif

Mar 25, 2011 | Honda CM 125 C Motorcycles

1 Answer

HI IM HAVEING A BIT OF PROBLEM WITH MY BAROSSA CHEETAH 250 CC QUAD BECAUSE WHEN I TURN THE PETROL TP ON THE PETROL RUNS STIGHT THROUGH THE CARBREATOR AND THEN STRIGHT OUT THE OVER FLOW, BUTS ITS ONLY...


The leaking carbuerettor needs to have its float level set.
Remove the air filter assembly, the fuel pipes and cables.
Remove the carbs and turn them upside down. Remove the float bowl on one carb. This will expose the float. Pull out the pin holding the float in place. (Note the position of the spring that holds the valve to the float.)
Remove the float and valve(looks like a very small pencil)
Inspect the valve tip for damage(unevenness) and replace if nescesary.
Reassemble the carb. Do not fit the floatbowl yet.
Measure float level by turning the carb on its side to have the float "dangling" Tilt it slightly so that the float rests on the valve. Measure the distance between the bowl mating surface and the bottom of the float(See diagram). The distance should be 24mm. If it is not correct, bend the tab at the valve to allow for a larger or smaller distance. Fit the float bowl and repeat for the second carb.


suzman_19.jpg

Nov 18, 2010 | Yamaha RD 250 Motorcycles

1 Answer

Briggs mod 216112011E. Won't start, carb cleaned wiith no change. I'd like to see a carb diagram to make sure the re-assembly was correct . I suspect the float could out of position but I'm not sure.Any...


This should help. As far as the float being out of position, if you invert the carb body (carb off mower) with the float hinge clip attatched, it should rest just about parallel to the body of the carb..a small straight edge will help..here are some diagrams
http://www.lawn-mower-shop.com/carb2.htm
Please vote on this solution.

Sep 08, 2010 | Briggs & Stratton Lawn-Boy Insight Series...

1 Answer

Yamaha dtr carb diagram


If the floats are sticking then bang the side of the carb gently with a hammer handle to dislodge them
Ride Safe
Bike-doc

Please mark this as useful (if it has been!!)

Aug 05, 2009 | Yamaha DT 125 R Motorcycles

1 Answer

Kawasaki EL250 carburettor


Turn off the gas and remove the float bowl. Remove the fuel line. Remove the float pin and float with needle valve. Do not bend the tang that the float needle sits on. Spray carb cleaner into the seat where the needle valve came from to clear out any trash in the valve casing. Spray the float bowl and interior of the carb. Remount the needle and float back in place and put the float bowl back on. Install an in-line fuel filter. The diagram below shows a 1994 carb Yours will be the same or close to it.

A “very helpful” rating on this answer? Thanks!

6d12579.gif

Jul 03, 2009 | 2001 kawasaki EL 250 Eliminator V

1 Answer

Ariens snowblower ST724 leaks gas from the carbourater


The little metal peice with the wire ataches to the float at the hinge part of the float, if you use yahoo type in tecumseh carburetor diagram then click on Parts and Diagrams and the web address is partstree.com it will show you a breakdown of a carb and how it goes together. It may not bee your exact carb but they are all pretty much the same. It also sounds like you may need to rebuild your carb. If you get it back together and it still leaks, I suggest you take it to a small engine repair shop and have them rebuild it for you only cause you need a special tool for the seat and the float will have to be set.

Dec 27, 2008 | Ariens 34 In. Zoom Series Riding Mower

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...