Question about Motorcycles

1 Answer

When pulling the clutch in when in gear bike still moving forwad

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Motorcycles Master
  • 22,158 Answers

Could be adjustment, could be wrong grade oil in chain case, could be sticking clutch ...

Posted on Apr 24, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch makes whineing noise. Bike does not move in gear with clutch pulled in when not running.


The gears won't mesh when the engine isn't running unless you rock the bike backwards and forwards with the bike off its stand.

As for whining, low oil is the first thing that comes to mind followed by bad bearings, and bent or worn clutch plates.

Oct 06, 2015 | Motorcycles

1 Answer

My dt wont stat in gear with the clutch engaged?


All the Japanese bikes I have owned won't start in gear unless you pull in the clutch lever. There is a small plunger switch fixed to the clutch lever stock (the part that does not move). This switch is connected to the ignition and starter circuits, so when the clutch lever is closed the starter won't turn. Check the bike starts OK when not in gear. If you try to start the bike in gear and it does not start with the clutch lever pulled then the switch is not working. Hope this helps.

Mar 04, 2015 | Yamaha DT 125 R Motorcycles

1 Answer

Hello I have replaced the clutch plates,the release cylinder seals and rebuilt the clutch master cylinder. There is no leaks and the system has been bled and it feels fine. When I pull the clutch lever in...


Back wheels often move when the lever is pulled in...this is due to hydraulic drag caused by the oil on the clutch plates and is totally normal. You should be able to stop the wheel by hand with the lever in.
With the lever out the clutch is fully engaged and the engine will therefore stall with the brake on...
As long as the wheel rotation can be stopped by hand with the clutch pulled in it's behaving normally...
Rocking the bike in gear is a method that's used to seperate the plates on a clutch that is dragging...usually if it's not been used for a while.

May 06, 2012 | 1987 Yamaha FZR 1000

1 Answer

I got a 87 yamaha fz1 and i cant use it because the engine dies whenever i shift it in a first gear.. some says that clutch is maybe too low or i need a new plate.. and i wanna know wers that location of...


Have you tried pushing the bike, in neutrol with the engine running, and put it into gear whilst moving, from your thread i cant work out if it is a clutch problem or not, if it is, with the engine turned off, put the bike into gear, pull in the clutch and push the bike the bike will not move because of the cluutch drag, if the clutch is working, it will be slightly difficult to move but it will move without the engine turning over but , other things to consider the wires are connected on the clutch safety switch on the handlebar micro switch ajacent to the clutch lever, also the side stand safety switch, check that the plunger on the switch is not sticking due to hardened grease, dirt rust, etc

Apr 30, 2011 | 1987 Yamaha FZR 1000

1 Answer

Started bike, pulled clutch lever, put bike in 1st gear, let out on clutch and nothing happened. clutch lever moves freely with no tension at all. when i put the kickstand down it shuts off like its...


The clutch lever should have some tension, so could be a problem with the hydraulic actuator stuck, or a failure of the clutch. try bleeding the clutch, or pull the clutch cover off and see if the pressure plate moves

Apr 22, 2010 | Yamaha YZF-R1 Motorcycles

1 Answer

1987 yz125 clutch not working!


If you can see the actuator moving, but not disengaging the clutch, it usually means that the clutches are hanging up in the basket, or the actuator is bad and not releasing the clutches. The only way to tell is to take off the clutch cover and watch what happens when you pull the clutch.

Aug 12, 2009 | 2003 Yamaha YZ 125

2 Answers

1987 kx125 clutch wont engage


push rod bent ? too short ?

Aug 06, 2009 | 2003 kawasaki KX 125

2 Answers

'95 Yamaha YZ 125 clutch - stays in gear when clutch is pulled in


the plates will stick to each other because of oil
check the clutch lever at the motor and make sure it is moving the arm that pushes the pressure plate and make sure it is moving

Apr 15, 2009 | 2003 Yamaha YZ 125

2 Answers

Engine cuts out


your clutch is draging adjust the clutch cable so that when you are on the bike with the bike off and in gear and clutch pulled in you can move the bike freely that means the clutch is engaged

Dec 30, 2008 | 2002 kawasaki KDX 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...