Question about GAS Motorcycles

1 Answer

What are the two adjustment screws, just above gas fill, labeled "L" and "H"? Then above those two holes is another labeled "T". Could someone provide nomenclatures. Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • GAS Master
  • 12,505 Answers

L is usually for low speed mixture and H is for the high speed mix. T is for the throttle or idle setting.

Posted on Apr 15, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a kozy world knw321 and pilot light is to high can this be adjusted i have tried blowing it out other heaters are burning fine but this one is burning to high don't know how to adjust it


Yes,pilot should be adjustable, but problem may be dirty accumulation on pilot fixture. With gas SUPPLY off, remove the grill and clean the pilot orifice and anything that might block air getting to the flame.
Check the hole where gas comes out of the pilot for accumulation of deposits. DON'T enlarge this hole beyond its original size.
On adjusting, you look at the gas valve and find a cap or screw that is identified PILOT adj.The actual adjustment screw is sometimes under the top cap or screw. If you're not sure, call someone who is knowledgeable.
Turning this slightly will adjust flame. don-ohio

Jan 22, 2017 | World Heating & Cooling

Tip

How to Refill the Epson R340's Ink Cartridge


<span>Instructional steps<br /></span> Things You'll Need: <ul> <li> <span>Syringes</span> </li> <li> <span>Refill ink</span> </li> <li> <span>1/16 inch thumb screw</span> </li> <li> <span>Paper towels</span> </li></ul> <ol> <li> Place the cartridge on a flat surface over some paper towels to soak up any spilled ink.<br /></li> <li>Drill a hole directly above the "H" in the word "Push" on the top label.<br /> </li> <li> Drill a hole above the the first hole so air can escape while you are filling the cartridge.<br /> </li> <li> Fill a syringe with the correct color and amount of refill ink. The black cartridge holds 25 ml of ink. Color cartridges hold 10 ml of ink.<br /> </li> <li> Insert the needle of the syringe into the first drilled hole. Slowly inject the ink into the cartridge.<br /> </li> <li> Replace the cartridge into the Epson R340. Allow it to rest for 24 hours so the ink can absorb into the sponge inside the cartridge.please rate this post by saying how helpful it is to you<br /></li></ol><span><br /><br /><a href="http://www.ehow.com/how_7414161_refill-epson-r340_s-ink-cartridge.html#ixzz13r3MVnYc"><br /></a></span>

on Oct 30, 2010 | Office Equipment & Supplies

2 Answers

For the pgo big max 50 cc they have the gear oil on thr left back side how are you supose to fill it ? Right when it goes to thr thread on the strew. I could find this answer in manuel


the bottom big bolt is the drain bolt.
the fill hole is a bolt which you take out to fill the fluid it is labeled with oil symbol or words. this is where you fill it.
there is another bolt you need to take out approx 1 1/2 inch above the botton, it should be labeled
fill or level but sometimes no marks, note: what your looking for is a bolt that dosen't attach anything, that bolt is specifically a level gauge bolt.

okay once drained, put the bottom drain bolt back in. and start filling in the top hole
until you see oil start coming out the fill/gauge hole, once you see oil start flowing out, put the bolt in and tighten, then put the top bolt in and your done.

dispose the old gear oil at your local auto parts store.
Best Regards
Big Al

May 22, 2011 | 2011 PGO Big Max 50

1 Answer

Headlight beam direction


Park the vehicle on a level surface, with the fuel tank about 1 / 2full and with the vehicle empty of all extra cargo (unless normallycarried). The vehicle should be facing a wall which is no less than 6feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicleshould be about 25 feet from the wall:
  1. If aiming is to be performed outdoors, it is advisable to waituntil dusk in order to properly see the headlight beams on the wall. Ifdone in a garage, darken the area around the wall as much as possibleby closing shades or hanging cloth over the windows.
  2. Turn the headlights ONand mark the wall at the center of each light's low beam, then switchon the brights and mark the center of each light's high beam. A shortlength of masking tape which is visible from the front of the vehiclemay be used. Although marking all four positions is advisable, markingone position from each light should be sufficient.
4dc0d0f.jpg

Fig. The head light alignment adjusters are located on the backof the assembly. Access holes are provided as necessary-2.0L Passat GLSmodel shown


Head lamps are adjusted from above. Do the following:
1. Open the hood
2. Look on top by the head lamps you should see two service holes (oneouter and one inner) where you will see a plastic adjustment screwwhich requires a hexagon wrench or a flathead screw driver that fits. Note the outer alignment screw is the hole located on top eg. driver side head lamps outter being the hole on the right side. innerbeing the alignment screw located in the hole on the left side of thedriver side head lamp assembly.
3. Lateral adjust/ horizontal adust is the right side hole.(which way to turn I've forgotten try incremental trial and error tilyou determine which way is left and which way is moving the beam to theright)
4. Vertical adjust is the adjustment screw located on theleftside of driver side headlamps assembly from above. turn counterclockwise to raise and clockwise to drop. its been awhile so i'm notquite sure .
5. Passenger side lateral and vertical adjust is symetrical. rememberoutter hole from above is lateral adjust and inner hole to the right inthis case for passenger side is vertical adjust.

More details: http://www.ehow.com/how_112704_adjust-headlights.html

Goodluck (remember rated this help).


Sep 04, 2009 | 2002 Volkswagen Passat

2 Answers

How do I do a basic tuning for a poulan pro 295? Just above the pull start are two access holes, one labeled "T", the other "L H". The saw is running pretty good, however I feel like it is not getting...


The `T` screw is your throttle control,the `L` & `H` is low and high speed. The normal procedure is to turn these two screws in full and then unscrew one full turn each. You start the saw and adjust the `L` screw gradually either way until it runs, do the same with the `H` screw while reving the engine. On some carbs. this can be tricky and needs a lot of patience, so if you are happy with the low speed only adjust the high speed. Hope this helps. Stephen.

Jul 02, 2009 | Poulan Wild Thing 2375 18" Gas Chain Saw...

1 Answer

Fuel draining out as soon as filled


ALWAYS have a fire extinguisher at hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

This is a carb float being stuck open.
Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Next, turn the gas back on and sharply tap the float bowl with the plastic handle of a screwdriver as the fuel bowl refills. The goal here is to vibrate the float to free it up. If doing this process a couple of times doesn’t free the float and fix the overflow problem, remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the
carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.

Please top rate this solution. Thanks!

May 08, 2009 | Yamaha Camry Motorcycles

1 Answer

Ttr 90 after 1/4 throttle just dies out


Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the
carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.

If the above does not solve the problem then pull the slide out of the throat of the carb and move the clip on the jet needle one notch lower.

Please rate this solution. Thanks!

May 02, 2009 | 2002 Yamaha TT-R 125

1 Answer

Fuel Leak from the Carburetor


Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Check the float as they can go bad and fill with gas such that they no longer float. Remove the idle screw and the air screw on the outside throat of the
carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the
carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. The idle speed will probably different so adjust the idle screw to get back to where it was. This process should get you back on the road.

Please rate this solution. Thanks!

Apr 23, 2009 | 1987 Honda CBX 250

3 Answers

GH1000 string trimmer


This is for the Black and Decker GH1000 string trimmer. There are 20 screws to remove altogether. The last screw is under the black label with instructions on using the button to extend the shaft. The screw hole is just above the white line on the label-you have to poke a hole in the label! Very tricky!

May 23, 2008 | Black & Decker String Trimmer Cordless 12"...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top GAS Experts

Ron Rak
Ron Rak

Level 1 Expert

47 Answers

rugby prop

Level 3 Expert

570 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a GAS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...