Question about Bajaj Motorcycles

1 Answer

Bajaj 180 Rouser not charging - Bajaj Motorcycles

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Bajaj Master
  • 40,748 Answers

Hi, Darwin before testing any electrical component in the Charging System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or ze ro amperage and must be replaced AGM types more so than lead acid batteries.
1. Battery Test: The battery needs to be a fully charged and load tested to ensure proper readings, connections need to be clean and tight. If you are not working with a fully charged and functional battery, all other voltage tests will be incorrect. Standing battery Voltage should be 12.5-13.2 DCV.
2. Charging System Voltage Test: Start motorcycle, measure DC volts across the battery terminals you should have a reading of approximately 13.2-15 DC Volts.
3. Check Connections/Wires: Inspect the regulator/stator plug, and check the battery terminals for connection/corrosion. If everything seems to be in order, move on to number 4 below to determine if there's a failed component.
4. Stator Checks/Rotor Check: Each of the following tests isolates the Stator & Rotor. If AC Output test Fails and Resistance Check, and Stator IB Test Pass then Rotor is at fault (Pull Primary covers and inspect rotor for damage).
5. AC Output Check:
Unplug the regulator plug from the stator
Start motorcycle and change Voltmeter to AC volts.
Probe both stator wires with your meter lead.
The motorcycle should be putting out approximately 18-20 ACV per 1,000 rpm. Reading will vary depending on system, check service manual specification
Generic Specs:
22 amp system produces about 19-26 VAC per 1,000 rpm
32 amp system produces about 16-20 VAC per 1,000 rpm
45 amp system produces about 19-26 VAC per 1,000 rpm
Stator Resistance Check:
Switch your multimeter to Ohm x 1 scale.
Probe each stator wires with meter leads and check resistance on the meter.
Resistance should be in the range of 0.1-0.5 Ohms. Reading will vary depending on system, check service manual for specification
Generic Specs:
22 amp system produces about 0.2 to 0.4 ohms
32 amp system produces about 0.1 to 0.2 ohms
45 amp system produces about 0.1 to 0.2 ohms
Stator IB test or Ground Check:
Switch your multimeter to Ohm x 1 scale.
Probe each stator wire with your positive lead on the multimeter and the negative to ground.
There should be no continuity to ground on either wire.
If there is continuity to ground your stator is shorted to ground.
5. Regulator Test: Each of the following tests isolates the regulator only, so if any of these tests fail, the regulator is at fault.
Identifying Wires:
Battery Charge Lead- Wire going from regulator to battery positive.
AC output leads- Wires coming from the Stator to the regulator.
Ground- Wire from Regulator to ground or regulator may be grounded via the physical bolting to chassis.
Regulator Ground Test: Ensure the regulator body is grounded or grounding wire is fastened tightly to a good ground (you should verify this by checking continuity from regulator body to chassis ground).
Fwd/Reverse Bias Test/Diode Test: This check is testing the Diode function to ensure it is regulating the AC current for the stator into DC Current.
Switch multimeter to Diode Scale.
Place your Multimeter positive lead on each AC output wire.
Place your multimeter negative lead on the battery Charge wire.
The meter should read voltage typically around .5 volts.
Next, switch your multimeter leads putting the negative lead on the AC output wires and the Positive lead on the Battery Charge Wire.
The reading should be Infinite.
With your meter on the same setting, place your multimeter positive lead on the regulator ground wire or to the regulator directly, and then place your meter negative lead on the AC output leads.
The meter should read voltage typically around .5 volts.
Next, switch your multimeter leads putting the negative lead on the regulator ground and the Positive lead on the AC output wires.
The reading should be Infinite.
Note: Below is a table to show the readings:
Positive Lead Negative Lead Reading
AC output 1 Battery charge lead Voltage
AC output 2 Battery Charge Lead Voltage
Battery charge lead AC output 1 ?
Battery charge lead AC output 2 ?
Ground AC output 1 Voltage
Ground AC output 2 Voltage
AC output 1 Ground ?
AC output 2 Ground ?
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.xbhp.com/talkies/help-me/23186-problem-battery-charging-plz-help-4.html
http://www.jetav8r.com/Vision/Stator/fault_finding_by_www.electrosport.com.pdf
Bajaj Pulsar 180 DTSi Workshop Manual
Rouser parts price list
Bajaj Pulsar 150 Maintenance Manual

Posted on Apr 22, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kawasaki rouser 180 backfires when running and feels like choking when going high gears.


Hi, Ryan and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a "LOAD" test "WARNING" you can have 12.5 volts or better but little or zero amps and the battery must be replaced.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Faulty main circuit breaker and or connections.
4. Faulty ignition coil and or connections.
5. Faulty spark plug, oil or gas fouled, wrong heat range or service type, wrong gap, loose in the cylinder head, broken electrode or insulator.
6. Faulty spark plug cables, leaking or broken, internal damage check for spark leakage in the dark.
7. Faulty ignition module, switch, CKP, MAP, CMP, sensor and or any connector in the ignition circuit could have corroded, loose, or broken pins/sockets
8. Burnt exhaust valve or air leak in the exhaust system.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Kawasaki rouser 180 help
Preventing Backfire on Motorcycle Exhausts DoItYourself com
Kawasaki Motors Philippines Commuter Bikes
Bajaj Pulsar 180 DTSi Workshop Manual
http://ondoc.logand.com/d/1735/pdf

May 16, 2017 | kawasaki Motorcycles

1 Answer

How to set timing rouser 135,i dont know to set correct


Hi, Asero for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
kawasaki rouser 135 set timing Google Search
Rouser 135 LS Compatible Aftermarket Spare Parts List
Rouser 135 Manual rar
OEM Parts for Kawasaki
Bajaj Electricals Pulsar 135 LS User Manual

Mar 29, 2017 | Motorcycles

1 Answer

Where can i find the fuse of my head light,horn, and signal lights..my motorcycle is kawasaki bajaj Rouser 200cc..


Hi, Jing sorry you can't find the first and best tool you ever bought for your Bajaj despair not for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
bajaj Rouser 200 fuse panel location Google Search
http://www.bcmtouring.com/imp/Pulsar_DTSi_Workshop_Manual.pdf
http://www.sterntech.com/pdfs/Pulsar_manual.pdf
Download Bajaj Pulsar 200 NS Spare Parts Catalog Manual

Apr 24, 2016 | kawasaki Motorcycles

1 Answer

Bajaj rouser carburettor


Hi Aslalajfd, I am sorry you can't find the first and best tool you ever bought for your Bajaj but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
How to adjust the Float Height on Carburetor Metric Harley and Asian
DOWNLOAD Bajaj Pulsar 180

Apr 21, 2014 | 2011 Bajaj Pulsar 180

1 Answer

How to adjust the headlight of rouser 180?tanx


Hi Anonymous, I am sorry you can't find the first and best tool you ever bought for your Bajaj but despair not for a mere $0 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
Rouser 135LS Service Manual PDF

Mar 12, 2014 | Bajaj Motorcycles

1 Answer

How to top dead center rouser 135


Hi, Alex I am sorry you can't find the first and best tool you ever bought for your Bajaj but despair not for a mere $0 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
Scooter Big Bore Chapter 3 Carburetor Valve Cover and Top Dead Center
Top Dead Center 2 AVI
Finding Top Dead Center on the Compression Stroke
How to find top dead center on Kawasaki 454LTD and setting the timing
Rouser 135 Manual rar



Dec 14, 2013 | Bajaj Motorcycles

1 Answer

My pulsar 180 battery is not charging . its 2010 model.


Hi, Nitindj2010 and the usual suspects are:
1. Voltage regulator/rectifier not grounded.
2. Engine ground wire loose or broken.
3. Faulty voltage regulator/rectifier module.
4. Loose or broken wires in charging circuit.
5. Faulty stator and/or rotor.
For more information about your issue, please visit the websites below. Good luck and have a nice day.
DOWNLOAD Bajaj Pulsar 180

Dec 29, 2010 | 2006 Bajaj Pulsar 180

1 Answer

My pulsar 180 battery is not charging .so plz give me wiring diagram bajaj pulsar 180 pdf".


Hi Nitindj2010, I am sorry you can't find the first and best tool you ever bought for your Bajaj but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
DOWNLOAD Bajaj Pulsar 180

Dec 29, 2010 | Bajaj Pulsar 180 Motorcycles

1 Answer

Necesito el manual de la moto Bajaj 220 rouser


Hi Cabespeedy, I am sorry you can't find the first and best tool you ever bought for your Bajaj but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
Service Manual Bajaj Pulsar 220

Sep 28, 2010 | Bajaj Pulsar 180 Motorcycles

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bajaj Experts

sachin sharma
sachin sharma

Level 2 Expert

171 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Joseph Gallucci

Level 2 Expert

120 Answers

Are you a Bajaj Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...