Question about Suzuki RF 900 R Motorcycles

1 Answer

Bike starts and stalls, then doesn't turn over.

My bike starts and will run if i rev the engine a couple times it will stay running until I get on and stand it up. Then it stalls and wont start, when i hit the ignition it wont turn over. Can you help?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

If it won't turn over when it's standing, but will when it's not, then it's a pretty safe bet that it's an electrical short!

Posted on Jul 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loss of power when in gear


Sounds like the carb is frozen or the ignition timing is way out (check distributor and loosen the clamp, turn it slightly with the engine running until it idles and revs up nice) . Reset the ignition timing, if that does not cure it, a carb rebuild is on the cards.

Vote for me if this helps, thanks.

Jun 25, 2010 | 2005 Suzuki Boulevard S40

1 Answer

I have a 1986 yamaha virago 700 that wont run properly


2 things need to be done first start your bike get a can of wd40 after your bike is warm and running spray around the carb jointsall 4 of them if your engine changes rpms up or down you have a intake leak ether your carb joint gaskets or o-rings need replacing or your carb joints are old and need replacing. at this point wont hurt to have you carbs cleaned also

May 03, 2010 | 1985 Yamaha XJ 700 X Maxim

1 Answer

How do I adjust the fuel mixture on a 1999 CL1500 CFX? It is running too rich.


Turn the fuel screws in until lightly seated. Back out 2 full turns on each carb. start bike and let it get to operating temp. turn screw out, or in to achieve highest idle for each carb. reset idle to about 1100-1300 rpms. Go back and forth between carbs and setting the idle. Rev bike a couple of good times and see that the idle drops normal with out stalling. Chaz Moto DC

Jan 22, 2010 | Honda Valkyrie Interstate Motorcycles

1 Answer

Fault with electric start on my Suzuki GSF 250 Bandit


Check that the clutch is in, kick stand up, and neutral light ablaze. Then try your start button. When you had it running and hit the button, the starter engaged at a slower speed then the bike engine was turning, which led to the stall. The stall means your starter works. If the starter works when the engine is running then it is wiring. Check your kick stand wiring along with the clutch wires which plug in on the handlle bar or where the clutch cable enters the engine.

Oct 18, 2009 | 1995 Suzuki GSF 250 Bandit

1 Answer

Engin wont stay running


check the spark plug sounds like you gotta fouled plug if that dont work get some carb cleaner and spray the carb out and check the air filter under the seat

Aug 07, 2009 | 2003 Yamaha YZ 125

1 Answer

Engine stalls when engage in any gear from neutral.


CHECK THE SIDE STAND SAFETY SWITCH IS OPERATING

Mar 19, 2009 | 2000 Suzuki GSX-R 750

6 Answers

Stalling problem from neutral to first gear


Hi and welcome to FixYa,

Initially, if the bike will be run without its own battery, the engine will really stall. This is because there will be no consumer for the voltage output other than the ignition system which will clamp down when the engine is revved and the voltage tends to go higher still.

Just a start, do postback how things turned up or should you need additional information. Good luck and Thank you for using FixYa.

Nov 27, 2008 | 1984 Yamaha XS 400 L Maxim

2 Answers

2002 Chevy Blazer stalls


check airflo sensor or potentometer,throttle pos sensor; if revs are to low when turning the wheel the power steering pump will draw power from engine, causing your other problems

Nov 14, 2008 | 2002 Chevrolet Blazer

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...