Question about 2003 Honda CRF 150 F

1 Answer

In order to remove the front tire on my crf150f do i just remove the 17mm bolt or what

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Yes take off the vavle stem bolt and the rim lock bolt (the 17mm) then get some tire irons and get to work

Posted on Jul 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tools are needed to replace the front right lower control arm on a 1999 Mercedes Benz E320


In order to replace the right front lower control arm you will a spring compressor. That's the most important tool you will need so that the spring does not fly out at you when you lower down the control arm. The control arm bolts are 21mm or 22mm nuts & bolts depending on if alignment adjust bolts installed or not. If adjustment bolts are installed then you will want to pay attention and note to which side the notches face so that you install them back into their original position. The ball joint nut will either be a 17mm or a 19mm. 16mm for the shock and a 22mm & 17mm for the sway bar link. Compressing that spring is the most important part of the jb though so don't forget to compress it.

Sep 17, 2014 | 1999 Mercedes-Benz E-Class

1 Answer

What is the bolt & nut size holding the rotor on the 2006 malibu ?


remove 2 phillips screw, unbolt caliper bracket w/ 17mm socket, use push bolt (12mm) to remove rotor if cannot be removed by hand

Nov 23, 2013 | 2006 Chevrolet Malibu

1 Answer

2007 toyota tacoma replace front wheel bearing prerunner


The other guys have never taken the wheel bearings out of a 2007 Tacoma! Remove the tire (duh)
Remove the 12mm bolt holding the brake line securing bracket
Un-clip the air sensor hose clip
Remove the two 17mm bolts holding the brake assembly on the back side
Remove the rotor from the wheel "spindle"- slides right off.
Unscrew the four metric bolts (maybe 17mm) holding the wheel housing to its mount (they cannot be removed from the assembly yet, see below).
That's right there is no normal wheel spindle with a big nut on the end of a threaded shaft in the middle!
The wheel mounting plate (with the 6 studs) is pressed into the bearing housing.
Get a replacement bearing assembly and take it and your old unit to a machine shop (unless you have a good press).
An easy job, just expensive- $140 for the bearing assembly.

Mar 27, 2012 | 2007 Toyota Tacoma

1 Answer

I cannot get a crescent, 17mm socket, or 17mm open end wrench on the rear left side crankcase drainbolt to save my life. I can easily access and remove the oil pan drainbolt and the front crankcase bolt,...


The clearence between the bolt heads and crankcase is very tight u might have to take a old 17mm socket and grind it down a little to get it on the bolt head. I think one bolt is for the oil in the engine and the back one is for the dry sump, there is oil in both at any given time.

Aug 09, 2010 | 2006 Yamaha Stratoliner Midnight

1 Answer

ALTERNATOR REPLACEMENT


Assuming this is a XG 350, the process is lengthly.
1. Remove the RH radiator cooling fan (two 10mm bolts at the top & wiring harness connector to it).
2. Lift vehicle to remove the Right Front wheel (then remove 4 10mm bolts securing the plastic splash shield & remove it)
3. Loosen the 14mm nut on the alternator belt tensioner pully
4. Loosen the tension on the belt by rotating (counter-clockwise) the 14mm bolt at the bottom of the idler pully and remove the belt.
5. remove the pully & the idler pully (three 12 mm bolts)
6. Loosen the 14mm nuts at the top and bottom mounting points of the alternator.
7. Using a floor jack (or vehicle lift), support the engine using a jack-stand & 2x4 piece of wood under the oil pan.
8. This is tricky - lift the engine 'SLIGHTLY' to take pressure off the front engine mount - loosen the 17 mm nut on top of the mount itself and observe engine movement. If the engine moves upward 'slightly' remove the 17mm nut - if not, raise the engine slight more until you see the mounting bracket rise off the mount.
9. Remove the remaining 17mm nut (deep well socket), and two 17mm bolts and remove the engine mount bracket.
10. Here's another tricky step. Some 350's bottom Alternator bolt bores are 'SLOTTED'... some are NOT. You'll need to determine wether you'll need to REMOVE the lower bolt, or just loosen the mounting sleeve at the bottom bolt. If it's 'sleeved', I use an air hammer to loosen the sleeve. If it's not slotted, I remove the lower bolt (it's the only way to remove the alternator and pry it off).
11. At the top is an "L" bracket which uses two 12mm bolts to attach it to the engine (head). One of the two 12mm bolts is difficult to get to -- do your best to remove it because the battery cable to the alternator is in the way.
12. Disconnect the alternator wiring (battery cable & regulator harness connector)
13. Lift the engine as high as it will go & pry the alternator off its lower mounting.
14. manuver the alternator upward taking care not to damage the radiator.
15. Installation is in reverse order.
NOTE: If your XG's lower mounting point was slotted, your task is easy. If it isn't, your task now becomes more difficult as you must align the new alternator to facillitate re-insertion of the lower bolt.
PS If not slotted, I use a telliscoping magnet to help re-insert the lower bolt.

Aug 09, 2010 | 2004 Hyundai XG350

2 Answers

How to remove rear wheel of 2006 honda crf150f


well i would say your very brave,,,but how will you balance this new tyer?????or would you be happy to have the bike doing bunny hops down the road???
for what it costs is it realy worth the efort doing it yourself?

Mar 27, 2010 | 2005 Honda CRF 150 F

2 Answers

Oil drain plug removal


3/8 inch drive ratchet and 17mm socket.

Feb 14, 2010 | 2006 Yamaha Roadliner

1 Answer

How do i put in a starter on a 1985 subaru wagon gl?


This is done from the top /under hood...remove spare tire which will expose the starter motor. Remove both mounting bolts(17mm) and the electrical connector and battery cable(12mm)

Aug 10, 2009 | 1983 Subaru Gl Wagon

1 Answer

Intructions to replace front pads and rotors Corolla


take off tires. two 14mm bolts behind the caliper. loosen the bottom 1. tilt the caliper up. slide caliper inward of the car, let caliper hang. two 17mm bolts behind the bracket take it off. and rotors should slide out. if rotor seized spray WD40 and hammer the rotor. careful don't hammer the stud it will screw up the thread.

Jul 31, 2009 | Toyota Corolla Cars & Trucks

Not finding what you are looking for?
2003 Honda CRF 150 F Logo

Related Topics:

441 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...