Question about 2001 Triumph TT 600

2 Answers

Signal problem i hooked up some front blikers and they worked for a min. then they wouldn't work the next day so i disconnected them and still none of them will work. fuses are good under the seat. any sugestions?????

Posted by on

  • mototech May 11, 2010

    check your turn signal relay sir. also turn on your blinker (any one of them) and check for voltage at the disconnected lead. next take one of the new signals and just touch the leads to your battery to ensure it is still operable. also try something else sir...with the new front blinkers not attached do your rear blinkers still function ?...they should and they should blink very fast since there is less of a load. if all this works out fine then the problem is the circuit load. many after market blinkers come with an in line resistor so as not to overload the smaller and less demanding LED or smaller blinkers. hope that helped out a bit sir.

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 66 Answers

Sounds like the old joke about blinkers 
Yes, they're on
No wait - they're off
Yes they are on again ........ 
[img]http://smilies.sofrayt.com/%5E/c0/bgrroll.gif[/img]


Are these LED lights or std bulbs? 
If the former, are you using load equalization resistors? 

First, validate that each of your indicators are still operational by connecting each lead directly to your battery. 

Most issues with installation of LED turn signals are associated with improper connection of the 'load' resistors. 
These resistors are intended to be connected across the lamp in parallel (i.e. between the positive & negative leads) not in series with the positive power connection. 
The best solution is to use NO resistors and install a non-load-dependent turn signal relay in place of the original. Leaving out the resistors, should at least get your signals working, albeit with a faster flash rate until the relay is replaced.  
The Triumph uses a special pin-out however so be sure to get one suitable for your application. 

Posted on Aug 13, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 29 Answers

LED ones? require less voltage, so relay gets conused. Fit indicator resistor (available anywhere, prob from where you bought the indicators)

Posted on Aug 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

None of the signals work , have led's on rear fender and standard on front


Hi Jerry, you may need a load equalizer, for more information about your question please visit the websites below. Good luck and have nice day. Motorcycle Parts Accessories Cycles

Nov 26, 2011 | 2000 Harley Davidson FLSTF Fat boy

1 Answer

Buttons won't work. Just returned from a 6 day golf trip where the SkyCaddie SG4 worked perfectly for the first 5 days. I recharged it in a wll outlet overnight, then on the next day the buttons...


Power On/Off and Key Lock/Unlock - Press the Power button located at the top right
of the Sky Caddie to power on/off or to lock/unlock the keypad. Upon pressing
the Power button you are prompted to choose either "Off" (Left Soft Key) to power
off the device or "Lock" (Right Soft Key) to lock the keypad. To unlock the keypad,
select 'Unlock" by pressing the Right Soft Key, then choose "Yes".

Jul 02, 2011 | SkyCaddie SG 4 Handheld GPS Receiver

1 Answer

I have problem with my '05 dodge ram 2500 cummins, I have a light on "4wdserv" and don't work 4wd drive, what it can? thanks


4 wheel drive service try un hooking the battery for 5 min and see if that clears if not go down to auto zone use there computer to clear it the computer wants you to change the gear lube in the front rear and rear rear it wouldn't hurt to check the level in the transfer case

Apr 23, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

Passenger side, front blinker and back blinker and brake light doesn't work. do i just replace bulbs or look elsewhere, and where?


Year? model? grab the hazard switch knob and try to move it about with the blikers on and see if you can get it to start blinking, you may need a new turn signal switch.

Nov 23, 2010 | Chevrolet Impala Cars & Trucks

1 Answer

Turn signals not working on 1990 dodge dynasty, but hazards are working?


the hasard's and the bliker's work on diferant flasher's on some car's or ther is a seperate cerket in the relay it's self replace the relay

Jun 05, 2010 | 1991 Dodge Dynasty

1 Answer

All blinkers stoped working


flasher relay
or bad earth [ ground ]

Jul 18, 2009 | 2001 Triumph TT 600

2 Answers

No RGB imput signal


You need to change the input signal, get into the menu on your monitor and change the signal from rgb to dvi, hdmi or vga dipending on what cable you using for connection.
There is NO rgb connector on that monitor

Good luck

Dec 05, 2008 | Balance CM2015 15" LCD Monitor

3 Answers

Trailer wiring for 06 GMC Canyon 4x4


exactly what does it do? please explain what happens when you press the brake turn on the light than brake signals ect.....

Aug 13, 2008 | 2006 GMC Canyon

Not finding what you are looking for?
2001 Triumph TT 600 Logo

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...