Question about 1997 Yamaha YZF 600 R thunder cat

1 Answer

Alarm has been disconnected then after reconnection without alarm kill switch is turning bike over which seems to bypass start switch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Check starter wire from handle bar back,you have cut wire during install and reconnected to a hot at all time wire

Posted on Jul 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 crown Victoria. viper alarm kill switch has turned all power to car. How do I reset


there is no override. Otherwise it would defeat the point of an immobilizer. I would find out why the alarm went off and deal with the rot cause rather than trying to bypass something made to be un-bypassable.

You may be able to reset the alarm by unplugging the battery from the car for a minute or 2 but I would start with the alarm manual to be safe. Possibly even remote the alarm and put the wiring back to stock.

Oct 16, 2016 | 1997 Ford Crown Victoria

1 Answer

Lights will not turn off


First you need to isolate the the key switch by unplugging it and test for continuity in the off position witch would mean the switch is bad.

Mar 30, 2014 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

2001 Hyundai Sonata V6 Alarm Constantly going off after reconnecting battery and car fails to start. Just replcaed crank sensor this morning and car ran and cranked as usual. Any ideas?


I don't think crank sensor has something to do with it unless the engine lights turns on and scanned were done and found the crank sensor code spits out... now you stated the alarm kept going off, question for you is the alarm a factory or aftermarket? if factory you are talking about maybe the anti theft triggered the " kill switch " to prevent from starting... what you can do is find the relay of the alarm module disconnected and try starting the car..

Oct 19, 2013 | Cars & Trucks

1 Answer

I can't turn off the security alarm on my 1998 nissan pathfinder


I couldn't turn off the security alarm on my 1999 Pathfinder as I replaced the battery,
Solution: I read the solution here to disconnect the positive cable, open the driver's door, insert the key, then reconnected the positive cable, while honking, I turn the key to the left, to the right and to the left again while the door is still open. The honking stopped. Then I started the truck without a problem. Thank you for the hint.

Jun 12, 2012 | 1998 Nissan Pathfinder

1 Answer

I have a code alarm tw1 with key-less entry remote start and starter kill in my 3000gt witch also have a factory alarm. i stored my car over the winter and disconnected the battery. i do this every winter....


Typically the toggle switch is the valet mode switch - basically disabling the system. Try turning the key to the on position and flipping the switch (or pushing the button) - also is there an LED light visible? Like to show the system is enabled? Blinking? Once you put it in valet mode it should go solid. Good luck.

Mar 13, 2017 | Vehicle Parts & Accessories

1 Answer

How to start 1995 jag xj6 bypassing alarm system


Disconnect battery, turn on ignition switch, reconnect battery

Feb 20, 2011 | 1995 Jaguar XJ6

1 Answer

Starter kill happens everytime i turn the key over to start my car


Did you install a bypass switch? Try taking the main fuse out of your alarm for a minute. Then reinsert it and see if you can start the vehicle then. Worse comes to worse, you have to reconnect that starter wire together and get rid of that starter kill option.

Jan 24, 2011 | Prestige Appliances Vehicle Parts &...

2 Answers

Battery dead


You need to hook the alarm back up and do a reset on the car.

Here is how you do it.

1) Turn factory original key to "ON" position for 5 seconds
2) Turn key to "OFF" position.
3) Repeat 1 and 2 again. Do it twice.
4) This should reset the computer to the chip inside the key.

If that didn't work,You will need to have the codes downloaded at the dealer.

Aug 08, 2009 | 1995 Nissan Maxima

2 Answers

Replaced bars on my 1994 Intruder 1400....now it won't start?!?!?


Kill switch activated or shorted during the bar change? Sidestand switch malfunctioning?

Jul 20, 2009 | 1994 Suzuki VS 1400 Intruder

1 Answer

Kill switch is on and I cant deactivate


you to disconect the main harness from the alarm.and take your car to a alarm repair shop.

Mar 10, 2009 | Directed Electronics 479V Remote Gen 2...

Not finding what you are looking for?
1997 Yamaha YZF 600 R thunder cat Logo

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...