Question about 2000 Harley Davidson FXSTD Softail Duece

1 Answer

Installing ignition knob on 1993 Ultra

I have a new knob with keys. It did not come with collar/spacer. Found old collar/spacer in saddle bags (just bought bike) but don't know how the collar/spacer go on before installing the knob. Does the ear on the spacer go on the top or bottom.

Thanks,

David

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 47 Answers

Bottom to hold it from spinning

Posted on Aug 22, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I instaled a new key switch to my 04 superglide. then installed a new battery. now i have power through the electric side of the bike but cant turn key off. no fuel pump no start and headlights on bra


Probably not installed and aligned correctly.

To Re-Install the Ignition Switch

FIRST for DOMESTIC BIKES : Install the two screws with flat washers at the base of the ignition switch housing and alternately tighten those screws to 36-60 in-lbs (4.1-6.8 Nm). OR FOR INTERNATIONAL BIKES: Install two new break-away screws with flat washers as follows: verify that the threads in the upper fork bracket are clean and in good condition because dirty and/or damaged threads may cause the heads of the break-away screws to snap off before the switch housing is properly tightened. Use great care to avoid losing the heads of any of the break-away screws anywhere in the motorcycle because normal motorcycle operating vibrations could cause these heads to damage paint and other surfaces, wear away wire insulation or do other damage to the motorcycle and/or its parts. Tighten the break-away screws in a clockwise direction until the heads snap off. THEN install the handlebars. Then install the ignition switch connector which is a 3-place Packard connector, at the front of the ignition switch housing. THEN install the anchor of a new cable strap in the hole at the bottom right side of the radio and tighten the cable strap to capture and hold the main harness conduit to ignition switch.

ON FLHX and FLHT/C/U: Install the fairing cap next. THEN, using the elongated holes in the fairing brackets and a long ball end socket install the four socket head screws to fasten the radio (the storage box on an FLHT motorcycle) to the left and the right radio support brackets and alternatively tighten those screws to 35-45 in-lbs (4.0-5.1 Nm). THEN install the outer fairing.

ON FLTR:Install instrument nacelle next and then install the switch position plate fitting the tabs into the slots of the fairing cap on FLHX, FLHT/C/U or on FLTR the instrument nacelle. The plate will easily snaps into the proper place when the parts are correctly installed. Be careful not to break off the tabs and if you do damage them replace them. THEN install the spacer over the threaded post of the ignition switch housing until it contacts the switch position plate and arrange/locate the spacer so that the widest side is forward and the inside tabs fit into the post slots. THEN slide the collar over that threaded post until it comes up against the spacer and place the collar so that the outside tab is forward and the inside tabs fit into the slots of the post. THEN screw the nut onto the post with the lip facing down and the smaller Outside diameter facing up. THEN turn the front forks to the right fork stop and using a 7/8 inch open end adapter wrench to tighten the nut. It should be tightened top 125-150 in-lbs(14.1-16.9 Nm). THEN install the spring into the bore at the underside of knob the knob and with that knob oriented toward the "FORK LOCK" position, insert the shaft into the threaded post. THEN while pressing the knob down turn the key clockwise to "UNLOCK" and you should hear it click into proper engagement if it is correctly engaged after which you can release the knob into its normally installed position where it should correctly rotate through all four operating positions. If it does not install correctly as above verify that the button at the base/bottom of the knob is pressed in and the key is turned to a apposition 60 degrees beyond the "UNLOCK" position. Try to rotate it again and if it is still not installed properly do the foregoing steps again. If it still will not properly install it may be that the knob was not removed while in the "FORK LOCK" position or it may have inadvertently moved out of this position while the knob was removed. In this case you will need to get or make an alignment tool and insert it until it fits in where the lock mechanism would fit and then holding the forks so they cannot turn rotate the alignment tool in a counter clockwise directionuntil the fork locks at which time remove the tool and try to install again as set out above. If it will still not install properly thedetent and switch position lugs are likely not aligned properly which can occur if the alignment tool or the ignition switch knob is rotated before it is properly inserted or bottomed in the ignition switch housing. In this case reinstall the knob shaft into the threaded post and gently rotate the knob until it drops into a partially installed position and note where it is pointing at that time i.e. is it pointing to the rear, to the "ACCESS"," IGNITION" or "OFF" position and then again remove the knob and reinsert the alignment tool so that the bottom of the handle is about 0.500-0.0750 in. (12.7-19.1 mm) from the top of the threaded post, and then hold. It there and rotate the tool counter-clockwise as far as necessary to get it to the "FORK LOCK" position and then go through the foregoing installation procedures again. When it is properly installed you are done and can reinstall the main fuse and side cover etc.

Jun 25, 2014 | Harley Davidson FXD Dyna Super Glide...

1 Answer

I need to fit saddle bags to the 2000 dyna wide glide. can anyone help?


Hi Anonymous, for more information about your question please visit the website below. Good luck and have nice day.
Easy Brackets Turn Signal Relocation Kit For Dyna Glide 406 595

Nov 17, 2012 | 2000 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

Fork lock locked up won't unlock


I don't know if this will help. It was sent to me by a friend of mine and I've never tried the procedure. I do not work on these ignition switches and fork locks. This is for a newer model but it may help. Good Luck. Steve

Here's the procedure to remove the IGNITION /LIGHT KEY SWITCH AND FORK LOCK for a 2005 FLHT/C/U or FLTR (Domestic): Tools needed for removing ignition switch A T27 Torx, a small flat blade screwdriver, 7/8 wrench.

1. Remove the outer fairing and windshield

2. To remove the ignition switch, insert the ignition switch key and turn to the UNLOCK position. Leaving the key installed, rotate the knob to ACCESS. Depressing the release button at bottom (left side) with a small screwdriver, push key down and turn an additional 60 degrees in a counter-clockwise direction. Lift and remove knob.

3. Using a 7/8 wrench on flats, loosen switch nut and remove from threaded post of ignition switch housing. Remove collar and spacer.

4. Using a T27 TORX drive head, remove the two screws (with flat washers) that secure fairing cap to left and right sides of fairing.

5. Remove the switch position plate by pulling tabs from slots in faring cap. If necessary, raise the fairing cap slightly to facilitate removal.

6. With the forks turned fully to the left, disconnect the Fairing cap switch connector (105) 12-place Multilock (black), from behind right side of fairing cap. Depress the button on the plus side of the connector to pull apart the pin and socket halves.

7. Remove the fairing cap from the motorcycle.

8. Locate the ignition switch connector (33), 4-place Packard, at bottom of radio. Slide connector off anchor and separate pin and socket halves.
9. Remove the socket screws (with flat washers) and lift the switch housing from the upper fork bracket bore. Route the ignition switch connector to rear of inner fairing and remove switch housing from the vehicle.

Sep 19, 2011 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Flhtcui key switch install, new out of the box


I've posted this before. I got this from a friend of mine and like I said before, I cannot attest to it's accuracy. I do not work on these types of ignition switchs. In the past, they required a special tool to align the switch that I didn't have. Anyway, this is what I have on the switch. I hope it works for you.

Good Luck
Steve

Here's the procedure to remove the IGNITION /LIGHT KEY SWITCH AND FORK LOCK for a 2005 FLHT/C/U or FLTR (Domestic): Tools needed for removing ignition switch A T27 Torx, a small flat blade screwdriver, 7/8 wrench.

1. Remove the outer fairing and windshield

2. To remove the ignition switch, insert the ignition switch key and turn to the UNLOCK position. Leaving the key installed, rotate the knob to ACCESS. Depressing the release button at bottom (left side) with a small screwdriver, push key down and turn an additional 60 degrees in a counter-clockwise direction. Lift and remove knob.

3. Using a 7/8 wrench on flats, loosen switch nut and remove from threaded post of ignition switch housing. Remove collar and spacer.

4. Using a T27 TORX drive head, remove the two screws (with flat washers) that secure fairing cap to left and right sides of fairing.

5. Remove the switch position plate by pulling tabs from slots in faring cap. If necessary, raise the fairing cap slightly to facilitate removal.

6. With the forks turned fully to the left, disconnect the Fairing cap switch connector (105) 12-place Multilock (black), from behind right side of fairing cap. Depress the button on the plus side of the connector to pull apart the pin and socket halves.

7. Remove the fairing cap from the motorcycle.

8. Locate the ignition switch connector (33), 4-place Packard, at bottom of radio. Slide connector off anchor and separate pin and socket halves.

9. Remove the socket screws (with flat washers) and lift the switch housing from the upper fork bracket bore. Route the ignition switch connector to rear of inner fairing and remove switch housing from the vehicle.

Sep 18, 2011 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

How to remove ignition switch on 2001 electra-glide


Here is something a friend sent to me. I've never taken one of these switches out so I can't say for sure if this is correct but it's all I have.

Here's the procedure to remove the IGNITION /LIGHT KEY SWITCH AND FORK LOCK for a 2005 FLHT/C/U or FLTR (Domestic): Tools needed for removing ignition switch A T27 Torx, a small flat blade screwdriver, 7/8 wrench.

1. Remove the outer fairing and windshield

2. To remove the ignition switch, insert the ignition switch key and turn to the UNLOCK position. Leaving the key installed, rotate the knob to ACCESS. Depressing the release button at bottom (left side) with a small screwdriver, push key down and turn an additional 60 degrees in a counter-clockwise direction. Lift and remove knob.

3. Using a 7/8 wrench on flats, loosen switch nut and remove from threaded post of ignition switch housing. Remove collar and spacer.

4. Using a T27 TORX drive head, remove the two screws (with flat washers) that secure fairing cap to left and right sides of fairing.

5. Remove the switch position plate by pulling tabs from slots in faring cap. If necessary, raise the fairing cap slightly to facilitate removal.

6. With the forks turned fully to the left, disconnect the Fairing cap switch connector (105) 12-place Multilock (black), from behind right side of fairing cap. Depress the button on the plus side of the connector to pull apart the pin and socket halves.

7. Remove the fairing cap from the motorcycle.

8. Locate the ignition switch connector (33), 4-place Packard, at bottom of radio. Slide connector off anchor and separate pin and socket halves.

9. Remove the socket screws (with flat washers) and lift the switch housing from the upper fork bracket bore. Route the ignition switch connector to rear of inner fairing and remove switch housing from the vehicle.

Sep 03, 2011 | 2001 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Im adding lights to my 2006 street glide.


You turn the ignition knob to LOCK position, and then you feel under the knob on the left for a switch. Push that up with your finger and at the same time, turn the ignition KEY (not the knob) counter clockwise for about 1/8 turn. You will feel a click and the knob will pull right out. After that, unscrew the collar nut on the threaded section and two metal pieces and a plastic spacer pull off. The fairing cap (the plastic cover) is attached by two bolts, on the outer sides. The wiring loom will disconnect when you unplug the connector.

Mar 10, 2009 | 2008 Harley Davidson FLHX Street Glide

1 Answer

Model EL7020 will not stay running!


Try turning the knob on top of the machine all the way to the right and try it again

Dec 04, 2008 | Electrolux EL7020A Oxygen 3 Ultra Canister...

1 Answer

Looking for sportster hard saddle bag installation instructions


nstructions Difficulty: Moderate Things You’ll Need: Step1 Determine what type of saddlebags you will be installing on your motorcycle. Saddlebags come in hard and soft styles, with each installed in basically the same manner. Hard bags tend to offer more security for your items but are a bit on the bulky side, while soft bags offering a little more flexibility. Step2 Check to make sure that your fender bolt area is clean and prepped for installation of your saddlebags. Both hard and soft saddlebags on Harley Davidsons are installed over the fender bolt area on the rear of the motorcycle, so clearing this area of debris and grime will keep it free of scratches and blemishes. Step3 Install any spacers or lifting brackets before you try and place your bags on your Harley Davidson. These spacers will keep you bags from resting against your exhaust pipes and will avoid damage to your motorcycle and to the bags themselves. Make sure they are installed tightly and spaced properly before mounting your bags. Step4 Open the saddle bag packaging and lay out the included hardware. The hardware will be necessary to properly mount your saddlebags to your fenders, so be sure that you do not misplace it. If your saddle bag comes with a fender mounting bracket, install it along the fender before proceeding. This bracket will be used to hold and stabilize your saddlebags, so it is essential that it is properly tightened and installed. Step5 Hold your saddle bag up to the fender and align the bolt holes in the saddle bag with the bolt area on the fender. Your saddle bag will have mounting holes in the side of the bag that will align with the mounting bracket. Place one of the bolts in the hole and tighten to hold it on. Put the remaining bolt in place and tighten them both securely once they are aligned correctly. Step6 Repeat this process with the remaining saddle bag. The bags should align evenly and be attached straight to avoid any imbalances or shifting while the motorcycle is in motion. Try and wiggle or move the bags to be sure your bolts are tight enough to prevent movement. Step7 Take your Harley Davidson for a short ride. Stop and check the fitting on your saddlebags and look at your bolts. Make sure nothing has moved during your ride and that all of your fittings remain tight. With just a bit of effort, your new saddlebags will make your Harley Davidson the envy of the neighborhood.

Nov 11, 2008 | 2006 Harley Davidson XL 1200 C Sportster...

Not finding what you are looking for?
2000 Harley Davidson FXSTD Softail Duece Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4821 Answers

Mike

Level 3 Expert

4348 Answers

yadayada
yadayada

Level 3 Expert

78936 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...