Question about 1994 kawasaki ZX-9R Ninja

1 Answer

Hi I own a Gpz 900r A1 will a A7 top end fit

Hi I own a Gpz 900r A1 will a A7 top end cylinder head fit

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes only the A1's were difrant A2-A9 the motor's never realy changed A7 had a better chamchain tensioner but from A2 the motor never realy changed Note the is for ZX/GPZ900R motors and not ZX9R's

Posted on Jul 22, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to change rear wheel bearings on gpz 900 r 1987

Take off wheel...remove cush drive on sprocket side...prise the oil seal out on the brake side and you'll see a circlip...remove this and drift bearings out. Drift new ones in with a socket or bit of tubing that is the same size as the bearing outer so as not to damage the circlip.

Apr 01, 2014 | 1987 kawasaki GPz 1000 RX

1 Answer

I am building a gpz 500 s street rat form a scraper and have just noticed that the left hand side filter for the carb warmer pipe work has been snapped off.can i cap them off or will the carbs ice up ??

capped off the system on my gpz1100e with no wet or winter problems...
just as likely to get carb icing on my 900r which has an intact system with new I wouldn't worry.
new filters are cheap enough though if you want to keep the system...

Oct 15, 2012 | 1987 kawasaki GPZ 500 S - GPX 500 R

1 Answer

The seat on my gpz 900r is stuck its been lying in the shed for 10 years. the lock will turn but it will not release the seat cheers Kev

Cool bike!, The seat latch is a bar with two hooks that runs across under the seat, you may be able to lever it forward by removing the right sidecover and probing with a long flatblade screwdriver.
From memory ,the latch is actuated with a cable from the lock that has probably broken or siezed.
Sorry, it's been a couple of years since I sold mine.

Apr 14, 2010 | 1986 kawasaki GPz 1000 RX

1 Answer

Does a 1985 gpz 75 have a compliance plate i cant find it on a bike i recently bought

I guess you mean a 750, The compliance plate should be on the steering head, right at the front between the upper and lower bearings. That is where it is on my 1984 900r and they are almost the same bike.

Apr 06, 2010 | kawasaki KX 450 F Motorcycles

1 Answer

I cant seen to find a socket to get my spark plugs out of my GPZ 600R, It must be a 18mm or 3/4 but nothing seems to fit as the hole in the cylinder head is very narrow

you have to use a deep well scoket and it can be 5/8 of an inch 11/16th's of an inch or 3/4 of an inch on a old 87 I think it's the one in the middle. Thanks for using fixya.

Aug 20, 2009 | 1987 kawasaki GPZ 500 S - GPX 500 R

1 Answer

Hi does the gpz 900r have the same crankshaft as the gpz 1000 rx . Thanks

No but there is not much between them if i remeber right the cam lobes are slightly bigger which would give you more air and fuel which maybe be detrimental. check cam lobe sizes in the haynes manual for 900 and 1000 and compare

Jul 10, 2009 | 1987 kawasaki GPz 1000 RX

1 Answer

Code 122 of A&, 93 Volvo 850

I am not a mechanic, but was recently looking into codes for my 1994 850. Here is what I found out...perhaps it will be useful to you if you do not already know this: The A1 313 is for a "Faulty gear position sensor PNP" ; can not find info on the others. My limited understanding is that the other codes refer to different systems; e.g. the A1 is for transmission codes, A2 is for fuel system, etc.

Jan 22, 2009 | 1993 Volvo 850

1 Answer

Kawasaki gpz 900r carbs

their either carb vent lines or fuel lines if vent lines the go under the tank if the are fuel lines they go to the petcock

Dec 30, 2007 | Harley Davidson Harley-Davidson Motorcycle...

Not finding what you are looking for?
1994 kawasaki ZX-9R Ninja Logo

Related Topics:

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4742 Answers


Level 3 Expert

78267 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides