Replacing halo and hid lighting in an after market headlight

Re: Condensation in Sienna Right Headlight.... - Toyota Sienna Forum

www.siennachat.com/.../4606-condensation-sienna-right-headlight.html
Mar 10, 2009 - 15 posts - ‎9 authors Over the years, I was not a frequent visitor to SiennaClub...but when I did visit, it was... in the right, passenger-side xenon HID headlight of my 2004 Sienna...the light has... Check with your dealer and see if they can do anything about it. .... :o The HID bulb is also a PITA to remove because you are working ... Re: 2004 Sienna no brake lights, radio, heater/AC ...
15 posts
Jan 4, 2013
Thread: HELP: Both Low Beams don't Work
6 posts
Nov 27, 2011
Thread: 2000 sienna drl and/or headlight issue
5 posts
May 7, 2010
Automatic Headlight Option: Useful or Not?
8 posts
Mar 3, 2010
More results from www.siennachat.com

Toyota 2004 Sienna repair: Replacing HID ballast or ...

toyotarepairsemipro.blogspot.com/.../replacing-hid-ballast-or-computer....
May 1, 2010 - Replacing HID ballast or computer control lighting for the Headlight. Just got a ... Up until now, I did not know I had the option of seeing twice as far with Xenon. Also up to ... In the end after buttoning everything up, the light did work fine. .... Howdo you determine if you have a HID or non-HID light? Reply ...

If it has a balast check on it if not then u need a ballast to cracnk up the juice to the HID

1. INSTALLATION GUIDE:



2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights



3. Parts Identification:



4. Projector Headlight



5. Halo & L.E.D.



6. Bottom of the Headlight:



7. Ballast Bracket, Halo Wires(red/black)



8. Turn Signal Adaptor



9. TOOLS REQUIRE



10. 10mm - 8mm socket



11. Philip Screwdriver



12. Crimper/Pliers



13. For more information about how to install your vehicle, come visit our youtube page on



14. http://www.youtube.com/spyderauto



15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.



16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.



17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.



18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.



19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.



20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.



21. STEP:



22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.



23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.



24. Factory Xenon Headlight



25. Spyder Projector Headlight using Factory Xenon Lights

follow this link to u-tube video not the exact vehicle but the principle will be the same,or search for your exact vehicle
How to replace low beam xenon HID bulbs 2006 BMW 330i

1. INSTALLATION GUIDE:
2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
3. Parts Identification:
4. Projector Headlight
5. Halo & L.E.D.
6. Bottom of the Headlight:
7. Ballast Bracket, Halo Wires(red/black)
8. Turn Signal Adaptor
9. TOOLS REQUIRE
10. 10mm - 8mm socket
11. Philip Screwdriver
12. Crimper/Pliers
13. For more information about how to install your vehicle, come visit our youtube page on
14. http://www.youtube.com/spyderauto
15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
21. STEP:
22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
24. Factory Xenon Headlight
25. Spyder Projector Headlight using Factory Xenon Lights
26. STEP:
29. PLS VOTE ME

BMW e46 HID Headlight Replace

Re: Replace headlight bulb

1. INSTALLATION GUIDE:
2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
3. Parts Identification:
4. Projector Headlight
5. Halo & L.E.D.
6. Bottom of the Headlight:
7. Ballast Bracket, Halo Wires(red/black)
8. Turn Signal Adaptor
9. TOOLS REQUIRE
10. 10mm - 8mm socket
11. Philip Screwdriver
12. Crimper/Pliers
13. For more information about how to install your vehicle, come visit our youtube page on
14. http://www.youtube.com/spyderauto
15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
21. STEP:
22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
24. Factory Xenon Headlight
25. Spyder Projector Headlight using Factory Xenon Lights
26. STEP:

BMW e46 HID Headlight Replace

I assume it didn't work before you changed the bulb either. You'll have to check for voltage at the bulb socket when the low beam headlights are turned on. If there is none you'll have to trace the wire back to where it splits from the right low beam headlight. If there is voltage there you have a problem with the new bulb.

There are two bolts, 10mm each. Take off these and pull the light straight off. Just plug everything back in when you get your new light. If it is an HID Halo type light, you will need to do some wiring.

how do you change front headlight blub 2008 sonata

INSTALLATION GUIDE:
BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
Parts Identification:
Projector Headlight
Halo & L.E.D.
Bottom of the Headlight:
Ballast Bracket, Halo Wires(red/black)
Turn Signal Adaptor
TOOLS REQUIRE
10mm - 8mm socket
Philip Screwdriver
Crimper/Pliers
For more information about how to install your vehicle, come visit our youtube page on
http://www.youtube.com/spyderauto
Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
STEP:
Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
Factory Xenon Headlight
Spyder Projector Headlight using Factory Xenon Lights
STEP:
pls vote an diam giving you link also for better help BMW e46 HID Headlight Replace