Question about 2008 Yamaha MT-03

1 Answer

How do I release the fuel line from the tank on an MT-03. I have removed the clip - its just the actual fuel line to break now but I can't see how it works properly so I can't release it.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Check the owners manual you should have got with the bike, if not check ebay there are loads available.

You will need to remove the two electrical connectors as well as the two pipes, one the overflow, the other the breather. Best to remove these first.

There is a safety cover that needs to be removed before you can release the main fuel plug. Once the cover clip is removed, the main clip needs to be squeezed at the release point (you should see the depress points), and pulled gently to remove. Best you have a friend hold the tank while you do this.

I found this to be a problem when I first removed the tank off my mt-03.

Posted on Jul 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

6 Answers

Regarding my 2009 Honda CB1000R. . How do I disconnect the plastic fuel line connector from the fuel pump on the underside of the fuel tank?


Ok so run your fuel tank low on petrol to make it easier to lift the tank tlift the tank pull the rubber stopper out and push the two blue tabs inward and pull the pipe off it can take a wiggle but no dealer tools are needed

Oct 18, 2014 | 2009 Honda CB1000R

2 Answers

Fuel line between the tank and the fuel filter


Is this the tank with the R clip if it is pull the clip out and pull the hose out

Sep 04, 2014 | 1996 Jaguar Vanden Plas

1 Answer

Mt-03 misfire high revs


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system, carburetor and/or filter.
12. Old dead or bad fuel.
13. Fuel tank vent system plugged or carburetor vent line closed off.
14. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
15. Carburetor controls misadjusted.
16. Damaged carburetor.
17. Incorrect valve timing.
18. Weak or broken valve springs.
19. Damaged intake or exhaust valve.
20. Check for engine trouble codes
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
Yamaha MT Owners Club
Total Motorcycle Forums
Yamaha MT 03 Service Manual
OEM parts for Yamaha
YAMAHA MT 03 Owner Manual

Feb 17, 2013 | 2007 Yamaha MT-03

1 Answer

1991 firebird 305 v8 TBI won't start,no fuel reaching carb


fuel pump is inside the fuel tank...you will need to drop the tank by removing the 2 straps that hold it up..make sure you put a jack under the tank so it does not fall and break the fuel lines when you get the straps off.
once you have the straps off , carefully lower the tank to provide access to the lines. Most likely you will need to aquire the fuel line removal tool...you can rent these fron Autozone..once the tank and lines are removed, you will need to get the fuel delivery module(FDM) out of the tank...there is a large "c" clip that holds the FDM in the tank...be careful when removing it cause usually the assembly is spring loaded and will pop up out once the clip is removed...now the bad news...the fuel delivery module may be very expensive for the whole thing...when at the parts store..see if you can just buy the pump assembly...the pump alone should be about 80-100 bucks...a delivery module may cost upwards of 300 or more...reassemble in reverse order...a word to the wise...when you take the tank straps off, there is the possibility that you may break the bolts...my experience with older cars is that you almost always break the bolts...so i just cut them off and replace with new ones

Mar 01, 2012 | 1991 Pontiac Firebird

1 Answer

How do I change the fuel filter on a 2003 blazer?


1. Remove your gas cap to relieve any pressure on the tank.
2. If it is easy to see, then is a cap and valve stem assembly on the fuel injection supply rail. A small squeeze on this will relieve pressure on that end. (Use caution for a small amount of fuel may seep out.
3. Your fuel filter should be located along the frame rail underneath your vehicle. Probably about even with the your drivers side door.
4. Remove the filter using normal hand tools on one end. The other end may be fitted with plastic clips that squeeze together to release the fuel line. (If you happen to break a clip they are available at most auto supply stores in the "HELP" section)
5. Remember that you will lose some fuel so be prepared when you remove the filter. USE CAUTION when first breaking the lines apart.. just in case of any pressure..


Best of Luck, and let me know how you come out..

Aug 20, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

Where the fuel filter located on a 2002 Ford explorer


your fuel filter is well hid !! the fuel tank is on the passengers side of your explorer on the fuel filer is located on the front top of your fuel tank ! access to the filter is obtained by removing the heat shield at the front of the fuel tank, there are two bolts retaining the shield to the right frame rail and two bolts retaining the shield to the cross member. once the shield is removed you will see the filter,Be careful removing the fuel lines, the lines have locking clips that DO NOT remove from the lines !! and can be damage if you are not careful (which will result in complete line replacement if the ends are broken. the line clips are released by disengaging the top of the clip then folding the the edge over towards the side its attached to next push both side's in (towards center on top edge) then push clip down part way while pulling line loose .Good luck Thanks for using fix ya

Jan 20, 2011 | 2002 Ford Explorer

1 Answer

How to remove the 2002 BMW 1150GS gas tank?


frist remove you seat and side covers there isnt much to take off but you need to. after that you'll see you fuel lines on the right hand side i pretty sure the 03 have the clip together lines kinda like a boat gas tank but smaller undo them. there will be a bolt on both sides of the tank remove them and slowly left the tank off
Good Luck
Mark

Aug 12, 2010 | 2002 BMW R 1150 GS

1 Answer

How to remove fuel lines from fuel tank 2001 Ford Ranger


special tool (about $15 at any parts store). It pushes in around the fuel line to release a clip inside , then the fuel line just slides off. Sometimes takes some wiggling and jiggling.

Mar 27, 2010 | 2001 Ford Ranger Regular Cab

2 Answers

How do I change the fuel filter on my 2000 Excursion? New filter has plastic clips


You need a small pocket screw driver and pinch the opposite end of the clamp to remove. Normally they come with new clips as the old ones break off. And if the filter has been on a long time the clips can actually wear out and can leak fuel if you don't replace them.you also have to remove the one or two mounting bolts holding it on.

Jan 28, 2010 | 2000 Ford Excursion

1 Answer

Fuel filter?


HI. this seems to be a faulty(clogged) filter but, i would also change the fuel pump as well. this is good preventive maintenance. the fuel filter can be changed in the parking lot. it is located near the fuel tank and, it is along the outer frame work, inline with the fuel lines.

You will need to separate the fuel lines on each end of the filter to release it. there will be clips on the ends of the filter that hold the fuel lines. be careful not to break these clips. it is very hard to release the fuel lines of the filter when these clips are broken.

To clarify the location of the filter, it is located Under vehicle, driver side, below seating area, front of fuel tank, mounted on frame rail in fuel line

Jun 01, 2009 | 2000 Pontiac Montana

Not finding what you are looking for?
2008 Yamaha MT-03 Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...