How would you replace a BCM, Body Control Module

Has to be programmed ,yes .
Body Control Module (BCM) Replacement
If the BCM is replaced, the following procedures must be performed in the subsequent order:
• BCM Reprogramming--Refer to Body Control Module (BCM) Programming/RPO Configuration in Computer/Integrating Systems for replacement, setup, and programming.
• Theft Learn--Refer to Programming Theft Deterrent System Components in Theft Deterrent.

A new body control module (BCM) must be programmed with the proper regular production option (RPO) configurations. The BCM stores the information regarding the vehicle options and if the BCM is not properly configured with the correct RPO codes, the BCM will not control all of the features properly. The Tech 2 software will automatically prompt you with the RPO available for the vehicle. Ensure that the following conditions exist in order to prepare for BCM programming:
• The battery is fully charged.
• The ignition switch is in the ON position.
• The data link connector (DLC) is accessible.
• All disconnected modules and devices are reconnected before programming.
To setup a new BCM, access the Vehicle Control Systems in Computer/Integrating Systems menu on the scan tool to program the BCM. Select Module Replacement/Setup and follow the instructions on the scan tool.
If the BCM fails to accept the program, perform the following steps:
• Inspect all BCM connections.
• Verify that the scan tool has the latest software version.

Body Control Module (BCM) Replacement and Reprogramming
If the BCM is replaced or requires reprogramming, the following procedures must be performed in the specified order:
BCM Setup -- Using a scan tool, go to Vehicle Control Systems » Computer/Integrating Systems » Module Setup » Body Control Module. Select Setup BCM and follow the on-screen instructions, making sure to select the proper RPOs and input the VIN correctly.
BPP Sensor Calibration--Refer to Brake Pedal Position Sensor Calibration
Program Key Fobs--Refer to Transmitter Programming
Setup SDM Part Number in BCM -- Using a scan tool, go to Vehicle Control Systems » Computer/Integrating Systems » Module Setup » Body Control Module. Select Setup SDM Part Number in BCM and follow the on-screen instructions.

Removal Procedure
Important:
• The ignition switch should be in the OFF position when connecting or disconnecting the connectors to the body control module (BCM).
• Always disconnect the black body wiring harness connector FIRST and the gray instrument panel (I/P) wiring harness connector LAST.
• Always connect the black body wiring harness connector FIRST and the gray I/P wiring harness LAST.
• Do not open the BCM housing. The module does not have any serviceable components. The module may be replaced only as an assembly.
Ensure the ignition switch is in the OFF position.
Remove the right front hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Right Side .
Disconnect the body wiring harness electrical connector (1) from the BCM.
Release the fastener retaining the body wiring harness electrical connector to the BCM. Remove the 2 fasteners retaining the BCM to the hinge pillar.
Remove the BCM from the hinge pillar by unlocking the integral tab.
Remove the BCM from the vehicle.
If installing a replacement BCM, program the BCM. Refer to Control Module References .

Remove the radio bezel. Refer to Radio Replacement .
Disconnect the body control module (BCM) electrical harnesses.
Remove the BCM from the instrument panel (I/P) retainer:
3.1. Pry the BCM tabs from the locking tabs on the underside of the restraint.
3.2. Slide the BCM out of the retainer

The BCM needs to be programmed if replaced !
The body control module (BCM) must be programmed with the proper RPO configurations. The BCM stores the information regarding the vehicle options and if the BCM is not properly configured with the correct RPO codes, the BCM will not control all of the features properly. Ensure that the following conditions exist in order to prepare for BCM programming:
• The battery is fully charged.
• The ignition switch is in the ON position.
• The data link connector (DLC) is accessible.
• All disconnected modules and devices are reconnected before programming.
The following procedures need to be performed to properly configure a BCM:
BCM Programming
Passlock Learn
Program Key Fobs

Body Control Module (BCM)
In the center of the I/P, behind the HVAC control module

Important: Perform new BCM setup when you replace Body Control Module (BCM). Refer to Body Control Module (BCM) Programming/RPO Configuration .
Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
Remove the left instrument panel insulator. Refer to Instrument Panel Insulator Replacement in Instrument Panel, Gauges and Console.
Disconnect the BCM electrical connectors.
Push the BCM up and move the bottom of the BCM away from and out of the mounting bracket slot in order to remove the BCM.
During Body Control Module (BCM) related service, the procedures below are designated to set-up the BCM correctly. Before you start, read these procedures carefully and completely.

Setup New Body Control Module (BCM)
Tools Required
Scan Tool (Tech 2) GM factory scan tool !
Important:
• Read this procedure carefully and completely.
• The BCM will not function properly if the Setup New BCM procedure is not performed.
• Perform the Theft Deterrent Re-learn procedure after successfully finishing the Setup New BCM procedure. If the Theft Deterrent Re-learn procedure is not performed after a BCM replacement, the following conditions may occur:
- The vehicle will not be protected against theft by the PASSLOCK system.
- The engine will not crank nor start. Your best bet is to take your vehicle to a dealer or a ASE certified repair shop who has proper tools .

2007 Scion tC Body Control Module - 1A Auto

www.1aauto.com > 2007 Scion tC

Shop at 1A Auto for a brand new Body Control Module (BCM) replacement for your2007 Scion tC at a great price. 1A Auto has a large selection of Body Control ...

HELP!!! BCM issue 2005 tc - Scionlife.com

www.scionlife.com/forums/scion-tc.../help-bcm-issue-2005-tc-165745/

Jun 30, 2009 - i think i have a possible BCM (body control module) issue with my 05 tc, ... Using 2007 Air Box in a 2005 Scion TC, chowdahound, Scion tC 1G ...

2007 Scion Tc Body Control Module - Auto Parts Discounter

1999 CHEVROLET BLAZER Body Control Module (BCM)

www.rockauto.com/catalog/x,carcode,1353619,parttype,2888

... V6 > Electrical > Body Control Module (BCM). 1999 CHEVROLET BLAZER 4.3L V6 : Electrical : Body Control Module (BCM), Price, Core, Total, Add to Cart ...

electric problem maybe bcm? - Blazer Forum - Chevy Blazer Forums

blazerforum.com > ... > 2nd Gen S-series (1995-2005) Tech

Oct 25, 2009 - I have seen on line it could be the bcm module. ... In my 1999 Chevrolet Blazer it is located under the cd/radio and computer climate control. Looking for a Diagram or Info on the Body Control Module
Feb 4, 2012
body control module
Sep 25, 2009
More results from blazerforum.com

ACDelco 19153625 GM Original Equipment Body Control ...

1999 CHEVROLET BLAZER Body Control Module (BCM)

www.rockauto.com/catalog/x,carcode,1353619,parttype,2888

... V6 > Electrical > Body Control Module (BCM). 1999 CHEVROLET BLAZER 4.3L V6 : Electrical : Body Control Module (BCM), Price, Core, Total, Add to Cart ...

electric problem maybe bcm? - Blazer Forum - Chevy Blazer Forums

blazerforum.com > ... > 2nd Gen S-series (1995-2005) Tech

Oct 25, 2009 - I have seen on line it could be the bcm module. ... In my 1999 Chevrolet Blazer it is located under the cd/radio and computer climate control. Looking for a Diagram or Info on the Body Control Module
Feb 4, 2012
body control module
Sep 25, 2009
More results from blazerforum.com

Body Control Module (BCM)
Under the I/P below the radio on the right side of the center console.
Do you know what the purpose of the BCM is ?
The body control module (BCM) has a bussed electrical center integrated into the housing. Body control relays and fuses are installed directly on the BCM, which simplifies wiring and junction blocks on the vehicle. The body control system consists of the BCM and its associated controls. Battery positive voltage is provided to the BCM from IBCM BATT 1 fuse and the IBCM BATT 2 fuse in the underhood fuse block. The module grounds are wired to ground G201, G203 and G305. The BCM is wired to the GMLAN High speed serial data buss, and the GMLAN Low speed serial data buss, as well as discrete input and output terminals to control the functions of the vehicle's body.
Serial Data Gateway
The body control module (BCM) in this vehicle functions as a translator between the High and Low speed GMLAN busses. The 2 communication protocols use the BCM to translate communicated serial data messages between the control modules over the 2 serial data busses.
Power Mode Master
This vehicles body control module (BCM) functions as the power mode master (PMM). Refer to Power Mode Description and Operation for a complete description of power mode functions.
Serial Data Power Mode Master
On vehicles that have several control modules connected by serial data circuits, one module is the power mode master (PMM). On this vehicle, the PMM is the body control module (BCM). The PMM receives 3 discrete ignition switch signals to differentiate which power mode will be sent over the Serial Data circuits. The 3-wire Ignition Switch table below illustrates the state of these inputs in correspondence to the ignition switch position:
Relay Controlled Power Mode
The body control module (BCM) uses the discrete ignition switch inputs Off/Run/Crank, Accessory, and ignition 1, to distinguish the correct power mode. The ignition 1 circuit is also routed to the Run/Crank relay for relay controlled power feeds during the appropriate power mode. The BCM, after determining the desired power mode, will activate the appropriate relays for that power mode.
Reprogram the body control module (BCM) after replacement. Refer to Control Module References .




Do you