Question about 2003 Yamaha YZ 250

2 Answers

We need to order a new piston and rings kit for a 2001 yamaha blaster 200. Not sure how the measurements work. Tha calabrator is reading 66.35 on the piston and the jug reads 66.52. so we are not sure what we should order. Anyone have an idea? Thanks

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 66 Answers

Take your cylinder to a mechanic and have them measure it. If you're using Weiseco forged pistons you could use a 66.50 but the factory tolorance is .003 so you are right on the edge of needing to have the cylinder re-bored. Weiseco pistons are set for the size of the bore and then they compensate for the tolorances. Don't forget that you will loose a little when you have it honed too.

Posted on Jul 22, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,689 Answers

Take the measurement of your block.

having a smaller ring will ensure block not being damaged but prone to a Blow-By. a too-tight ring can get your block damaged. so for you to know which size to get regardless of the stock size, tyr to get the block measurement first, then off you go wich ring to get

Posted on Jul 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My question is if the piston seized up into the cylinder head do I need to replace the whole head or just buy a top end kit


The piston wont seize into the cylinder head it will seize into the cylinder and you will have to replace the piston the rings the cylinder. crankshaft bearings and seals and gaskets. maybe the cylinder head if it got hot enough to warp

Oct 18, 2015 | Motorcycles

1 Answer

I have a Yamaha blaster 200 ,they star but a won't accelerated star a buginau


Hi, Javier and the usual suspects are:
1. Throttle cables misaligned or misrouted.
2. Damaged or restricted fuel tank venting system.
3. Inlet system air leak.
4. Vacuum piston malfunction.
5. Accelerator pump leaking or no output.
6. Plugged bowl vent.
7. Fuel level in bowl too low.
8. Restricted fuel supply passages.
9. Plugged jets or passages.
10. Worn or damaged needle or needle jet.
12. The enricher valve not seated or leaking.
For more information about your issue please visit the websites below. Good luck and have a nice day.
how to clean carb 1998 yamaha blaster
Yamaha Banshee Needle Float Test and Replacement
Yamaha Blaster Parts Service and Owner Manuals Free Download
http://www.yamaha-motor.com/assets/service/manuals/2001/lit-11626-14-09_246.pdf

Jul 26, 2015 | Yamaha Motorcycles

1 Answer

2004 yamaha blaster will idle but will not take the throttle all new engine


Either stale fuel, blocked pilot jet or low compression spring to mind

Ride Safe

Bike-Doc

Jan 22, 2012 | Yamaha YZ 250 Motorcycles

1 Answer

Hi my blaster 200 quad just went dead while rideing wheels wanted to lock then just switched off i tried to start with the kick but noticed no compression at all on the kick could this be a rings en...


Dear blaster , i request to you please call bike tech for all type of inspection of your bike, after long time vehicle was not start because his all parts is jam.

Jun 20, 2011 | Yamaha RD 250 Motorcycles

1 Answer

Hi, i recently bought a yamaha blaster 200cc quad bike and when i went out on it i forgotten to put some 2 stroke oil in with the fuel tank, and when out on it. now it wont start, please could you tell me...


you probably seized the engine. The piston rings have most likely scored the cylinder wall. At the very least you will have to rebuild the top end. Oversize rebuild kits are available. You will have to have the cylinder bored to a larger diameter to accept the oversize piston kit.

http://cgi.ebay.com/ebaymotors/Yamaha-Blaster-040-Platinum-Piston-Engine-Rebuild-Kit-_W0QQcmdZViewItemQQhashZitem1c1ad757dbQQitemZ120709404635QQptZMotorsQ5fATVQ5fPartsQ5fAccessories

The crankshaft is also lubricated by the oil in the fuel. There is a possibility that the crankshaft is also toast due to lack of lubrication. You will have to tear the engine down (top end) to verify the damage. you could remove the exhaust and look into the exhaust port to view the condition of the piston.

You may be able to find a used engine at a reasonable cost from the internet. Google search.

Jun 03, 2011 | Yamaha yZF15 Motorcycles

1 Answer

Not getting any spark on my yamaha blaster


i have a 2001 yamaha blaster that has no spark i bought a new coil and still nothing anyone know whats up

Mar 17, 2010 | 2001 Yamaha TW 200

1 Answer

Having trouble with my 93 yamaha 200 blaster how do i rebuild the motor


You should get a good manual. You will need it for specs anyways. It will give you tolerances that you will need to measure to verify if your piston, rings, and cylinder is still usable. I recommend the factory one, but clymer and hayes also make them.

Sep 12, 2009 | 1985 Yamaha XJ 700 X Maxim

Not finding what you are looking for?
2003 Yamaha YZ 250 Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...