Question about 2001 Harley Davidson FLHTCUI Electra Glide Ultra Classic

2 Answers

Low idle on start 400 rpm pops when you let off

When you try start it you have to throttle it to start. it idles sometimes about 400 RPMS and when you let off it pops a little bit i think a little bit to much .

Posted by on

  • paule64 May 11, 2010

    injected or carbed?

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 150 Answers

Its your idle sensor sits behind your aircleaner on top forward of carb well fuel injectors. Anyway its two screws replace it.

Posted on Aug 27, 2009

  • v2iper
    v2iper Aug 27, 2009

    its your idle sensor sits behind your aircleaner on top forward of carb well fuel injectors. Anyway its two screws replace it.

  • v2iper
    v2iper Aug 27, 2009

    its your idle sensor sits behind your aircleaner on top forward of carb well fuel injectors. Anyway its two screws replace it.

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 72 Answers

Main idle jet in the carb is clogged

Posted on Aug 24, 2009

  • homerhibbard Aug 24, 2009

    main idle jet in the carb is clogged

  • homerhibbard Aug 24, 2009

    main idle jet in the carb is clogged

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hard to start, dies, missing out, hesitation, low rpm take off missing out


Fuel filter clogged, weak or faulty fuel pump. Have fuel pressure checked, if its ok, then check igniton coil or module.

Dec 13, 2013 | 2000 Chevrolet Silverado 1500

2 Answers

I have a 95 1500 with the 350, sometimes it starts and runs great, other times right after it starts it will shoot up to 2000 rpm, the service engin soon light comes on and if you drive it, everytime you...


Try removing and cleaning the idle control solenoid on the throttle body. They get contaminated with carbon build-up and gives you an erratic idle. It's the round solenoid that screws into the side of the throttle body. When you remove it you'll see a spring loaded plunger that needs cleaning with throttle body cleaner and you'll need to clean the seat inside the throttle body as well.12_24_2012_2_14_19_pm.png

Dec 24, 2012 | 1995 GMC Sierra

1 Answer

05 Bandit 1200S idles low, run rough at low rpms,


Try buying new diaframs for your carbs, because of the diafram and piston operation, if the diafram becomes weak due to heat from your engine, and by the diafram not beeing rigid enough, it hesitates to lift the needle out of the jet causing the lack of fuel at low tack/rpm when throttling up or accelerating slowly.

Jun 11, 2010 | 1997 Suzuki GSF 1200 Bandit S

2 Answers

Its starts and runs good, but it is not able to idle, i will rev it up to keep it running and it either gets to like a 300 rpm idle for a second or so then just dies, or it will be like it has a stuck...


Assuming you haven't done anything to the carb or cable, the revving up would indicate an air leak somewhere around the carb manifold, either at the head or at the carb/manifold couple.
300rpm is very low for a single to idle at, it should be around 600rpm for reliable idling.
To check for air leaks, spray CRC or WD-40 around the manifold while the bike is idling - you will hear a change in speed.

Jun 29, 2009 | 2002 Yamaha TT-R 250

2 Answers

Idle rpm problems


Check and clean th egr valve or just replace it. Sometimes I have seen that both the EGR and the IAC need to be replaced and sometimes, people only replace one. I personally on my own vehicles when this happens I just replace both at the same time

Jun 02, 2009 | 1998 Dodge Durango

Not finding what you are looking for?
2001 Harley Davidson FLHTCUI Electra Glide Ultra Classic Logo

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5060 Answers

Mike

Level 3 Expert

4354 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...