Question about 1993 Honda CBR 600 F(2)P

1 Answer

Put new carb on 86 cr 80 ran fine 4 10 minutes then quit changed spark plug and gas still nothing. has spark dont know how hot also changed manifold appeared to be dry rotting still nothing. even attemped dumping gas down the spark plug inlet nothing

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

For any motorcycle to run you need three things. spark, fuel and compression. i see you've tried to get fuel and spark. if you have spark thats one down. dont pour fuel into cylinder. instead spray tiny bit of brakeclean or carb clean into spark plug hole. i have a feeling if you drained your gas after the carb clean the carb most likely sucked bad gas back up and might need cleaned again. ive seen it happen alot on ols bikes.

Posted on Jul 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a Poulan PR208 Stormforce snowblower that quits after 2 or 3 minutes.


Chcek stuck or loose choke flaps and integrity of carb manifold gasket. Check the ignition coil cable (connected to the spark plug). The kill switch wires should not any crack that may touch the chassis ground.

Dec 29, 2016 | Cars & Trucks

1 Answer

My cr 80 won't start but it's popping like it won't s to replaced spark plug an couple over things please help me sum one


Hi Lennard:
Cars and trucks section but CR80 sounds like a motorcycle. right?
You need two basic things:
1) Spark - pull the spark plug, connect the lead, hold against the head, and spin it over. Spark shoulld be hot and blue.
2) Fuel - Drain tank and fill with fresh gas
Drain and flush carb
If it has a filter, make sure that fuel is flowing through it.
Try a "normal" start........... choke, kick over 5 times. If no start, remove plug and check for fuel in cylinder. Wet plug means no spark. Dry plug means no fuel.
If dry plug try priming the carb (give it a squirt of gas with choke off)
It should try to start.
To let me know how you're doing, reply as a comment on this post.
Cheers.

Nov 08, 2015 | Cars & Trucks

1 Answer

ProForce PWC102350 2,350 PSI 2.3 GPM 163CC MagnaForce Gas Powered Pressure Washer will not start


If you have compression then the first thing you check is for spark. If you have spark then you move on to the fuel system. You will have to pull off hoses at a couple of points to see if gas is at the carb and further along. If it is the carb then a simple carb kit will work.

Apr 13, 2014 | ProForce PWC102350 2,350 PSI 2.3 GPM 163CC...

1 Answer

I have a 1985 Yamaha maxim that hasn't been ran


Spray starter into the carb intake with no choke, if she runs for a few seconds then you know its fuel starvation
clean jets & airways & blow through with compressed air

Nov 20, 2011 | 1985 Yamaha XJ 700 S Maxim

1 Answer

I have a 1991 honda cr 250 I cant get to start at fist gas ran right thru carb and out bottom i took carb apart and got the floats to stop sticking cleaned it out with carb cleaner put back together but...


try a new spark plug. if u fowl out a plug some time they will not fire under compression.2 strokes need. fuel,fire and air, very simple engines.it is possible crank seal are bad .that doesn't allow the engine to create vacuum in the crank case.thus fuel and air will not make it to combustion chamber.

Jul 11, 2010 | 2002 Honda CR 250 R

1 Answer

Husqvarna 51 died and wont restart


hi
if you have a good compression,a strong enough blue spark and carburetion for the fuel air mixture try priming the engine(put small amount of gas in the spark plug hole)then start the engine.If the engine runs only the gas you put inside the cilinder there is a carburetion problem to find and fix.
let me know regards savumihai71

Apr 13, 2010 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

1 Answer

Toro SR4 Running problem when hot


It can be quite a things - a blocked air filter or a blocked exhaust. To clean the exhaust, unbolt it from the manifold, hold it vertical and hit on the side until no more soot comes out. Changing the air filter should be pretty straightforward. If the spark plug bottom end is black then you have the fuel mixture too rich and you should lessen the flow of fuel.

Apr 07, 2009 | Garden

1 Answer

Bike bogged down like plug fouled now wont start


Based on the information given, I think you may have a hole in the top of the piston. It sounds like pre-ignition, ( AKA detonation and engine knock ). Pull the cylinder head and check the piston and cylinder head. Sometimes the top outer edge of the piston disintegrates due to the heat. Replace the piston and rings and remove the carbon from the head. Be sure you run 32/1 mix on gas and oil. That's 4oz two stroke oil per gallon of gas. Only use premium gas.

Remove and clean the carb. Be sure the carb mount bolts and carb manifold bolts are tight. An air leak will cause the engine to run hot.

Please rate this solution. Thanks

Apr 06, 2009 | 2003 Honda CR 125 R

Not finding what you are looking for?
1993 Honda CBR 600 F(2)P Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5060 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...