Question about 1986 Yamaha FJ 1100

1 Answer

Can`t get netural

Hello

Bikes very hard to get into netural , especially when running,i put clutch fluid in but still the same . The bike is idle a lot and is seldom used mabey it just needs a squirt of oil somewhere ? hope you can help. its an FJ1200 1990.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 677 Answers

Yep I can help.The clutch has about 6-8 or more plates in it.When they are not used they can stick together.It needs to be taken apart,cleaned and put back together in exactly the same order.Instead of all the plates slipping,only a few spin.This goes into the g/box and makes it spin when it should be stopped.The fj have a great clutch in them.This may really help your problem.

Posted on Jul 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1984yamaha virago 1000. with the bike running, when I try to shift from neutral to first gear the bike stalls. I think it has something to do with the electrical.. Help!


If you are at idle, in neutral, with the clutch lever pulled all the way in, and you shift into gear and the engine dies, it is likely the switch at the clutch lever. When they fail the bike does not get the signal that the clutch is disengaged and it is safe to shift into gear. Have that switch checked. Some bikes also have a side stand switch, make sure your side stand is always up before putting you bike into gear.

MGM

Sep 13, 2013 | Yamaha Motorcycles

2 Answers

Clutch gl1000 honda creeps when put in gear hard to find nuatral sat 10yrs


Get car oil out - friction reducing properties ruin wet clutches - put bike oil in
Make sure cable is adjusted properly
Plates may get stuck together after time unused - see my tip for quickly releasing seized clutches
Ride Safe
Bike-Doc

Jan 07, 2012 | Motorcycles

1 Answer

The bike will crank up and idle and I can thottle it up fine but as soon as i put it in gear and release the clutch it dies.


is the kickstand still down when you are doing this. Some bikes have a kickstand sensor and wont let it run when down.

May 18, 2011 | 2002 kawasaki EN 500 Vulcan Classic

1 Answer

Coolant leaks


Any of the yz and wrf 250 and 426 ,450 will overheat and water will come out of the radiator if you let it sit and idle.After a hard run it happens quickly.20 seconds.After a cold startup,5 mins.If you own one of these bikes,turn it off after TEN seconds of idling.ESPECIALLY after a hard ride.Basic rule.They do not like to idle.They need air over the radiator......Hope this helps

Mar 09, 2010 | Yamaha YZ 450 F Motorcycles

1 Answer

Kdx 200 clutch not engaging properly


The clutch in your bike is a wet clutch. There is a lot of hyrdostatic friction even when the clutch is released completely. I think a large factor is the type, age and condition of oil. Perhaps something as simple as an oil change would help.

Jan 14, 2010 | 2005 kawasaki KDX 200

3 Answers

2009 Street glide idles poorly, strong gas smell, stalls


The 09 models come with a "parade" mode which causes the rear cyclinder to quit firing when idling in traffic etc to combat over heating. You should be able to kick it on by rolling the throttle grip FORWARD for 5 to 10 seconds. Have you changed the pipes or air filter? If you have and never had the EFI adjusted (either factory download or fuel tuner installed) your bike could be running extra rich causing the over heating and eventual engine destruction. New Harleys run rich from the factory, any changes to the intake/exhaust system without proper fuel injection management will cause overheating. Try getting your bike into parade mode by rolling the throttle forward to the stops for a few seconds, that will cool things down.

Jun 28, 2009 | 2008 Harley Davidson FLHX Street Glide

1 Answer

03 zx12r clutch wont disengage


the clutch disks are stuck together

Apr 21, 2009 | 2003 kawasaki ZX-12R

1 Answer

Where do I find the netural start switch on my 89 zxr250?


The neutral switch is mounted in the left end of the shift drum. It is part number 13151-1080. There is an associated part, "PIN-neutral position" #92043-076 The pin is under a bolt screwed into the top case. Bad switch or loose wire connection.

Please rate this answer. Thanks!

Apr 19, 2009 | 1989 kawasaki ZXR 250

2 Answers

Tiger triumph 2008 brand new wont start... help


Hi and welcome to FixYa,

If I may suggest:
  • re-charge fully the battery. It may have run down on the previous tries;
  • thereafter, switch IGN to ON and verify pump running felt on the tank;
  • neutral, engine switch ON, IGN switch ON, clutch IN, start.
Just a start, do postback how things turned up or should you need additional information. Good luck and Thank you for using FixYa.

Nov 23, 2008 | 2008 Triumph Tiger ABS

Not finding what you are looking for?
1986 Yamaha FJ 1100 Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Tom

Level 2 Expert

314 Answers

vince

Level 3 Expert

1216 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...