Question about Harley Davidson FXSTB Night Train Motorcycles

1 Answer

V/H short shots W/new air cleaner and fuel pack ran fine for three months now check engine light on and runs rough.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Harley Davidson Expert
  • 284 Answers

Check your plugs, if the fuel pak is set to rich the plugs will get fouled allowing it to run rough or not at all.

I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_5bac37c3cb991fdb

Posted on Aug 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my engine run perfect for 5 minutes then rough?


Sounds like a fuel starvation issue. Does the choke stay open? The motor could be overheating, too. Make sure the heat sink blades are free of junk.

Jul 22, 2014 | Kawasaki Engines NEW 19HP KAWASAKI ENGINE...

2 Answers

We just purchased a 2002 Ford Escort. Tonight, when starting the car, it ran very rough and then died. We started it again and it ran fine after that. It has happened twice and it has only happened when...


Could be a idle air problem. The injector could be leaking when you shut it off ..Try some injector cleaner see if it gets better..The idle air shouldnt run rough just idle real low or sometimes it will get stuck and idle high....Are you losing any antifreeze..If you are the 2.0 SOHC engine bad about leaking antifreeze into the cylinder and makes the engine run rough until it burns it out..See if you can see the smoke coming out when it happens..White smoke indicates antifreeze,,Black smoke indicates fuel..

Sep 04, 2011 | 2002 Ford Escort

1 Answer

1995 Pontiac Grand Am won't start


is it poss the engine is flooded with fuel? if you can remove the spark plugs see how wet they are. If wet, replace turn engine over while they are out remove fuel pump fuse and coil pack conector b4 you do this if unable to do this hold the gas pedal down all the way to the floor your vehicle is fuel injected this will create a fuel shut off mode which while held down will not deliver any fuel to the engine as the engine starts to fire and run rough take you foot of the pedal ane nurse it until it runs ok if it runs get your mechanic to check for leaking injectors dripping over night

Jun 05, 2010 | 1995 Pontiac Grand Am

2 Answers

Idles rough


To add Solution #1...Based on the mileage you are getting, this looks like a 4.0. More than likely the intake plenum has a crack in it. The carb cleaner should verify this - when you spray it around the throttle body the engine should run very smoothly for a short time.
You should also be able to tell if this is the issue by looking at your fuel trim values and O2 sensor readings.

Nov 24, 2009 | 2001 Oldsmobile Aurora

2 Answers

1996 Ford Windstar engine runs rough


DIS ignition, no distributor to " get in there " with....

Jul 02, 2009 | 1996 Ford Windstar

2 Answers

Rough idle P0300


a faulty MAF will not cause a P0300, just a severe loss of power, look for injector, ignition and intake vacuum leaks as your causes.

Mar 20, 2009 | 2000 Chevrolet Impala

1 Answer

91 LEGACY STARTED RUNNING ROUGH


The cylinders are numbered as on the spark pack you changed. You might have done better putting the seafoam in the tank as an injector cleaner. Not sure why you changed so many parts, you seem to know how to get the codes from test connector lead hookup and the blink pattern. You might also want to check the fuel rail pressure and the crank and cam angle sensors. Before replacing the injector, swap the #4 injector with the adjacent one and see it the code moves with the injector or stays put. If the code stays on #4, then check the injector wiring, if it moves clean or replace the injector.

Mar 16, 2009 | 1991 Subaru Legacy

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Gar
Gar

Level 2 Expert

384 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5065 Answers

Mike

Level 3 Expert

4354 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...