Question about 1996 Suzuki GSX 750 F (Katana)

1 Answer

How to adjust carberator floats - 1996 Suzuki GSX 750 F (Katana)

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Suzuki Master
  • 9,098 Answers

  1. Suzuki GSX750F Katana - Motorcycle Specs

    www.motorcyclespecs.co.za/model/suzu/suzuki_gsx750f_05.htm Suzuki GSX 750F Katana. Year. 2004-05. Engine. Four stroke, transverse four cylinder, DOHC, 4 valves per cylinder. Capacity. 748 cc / 45.6 cu.in. Bore x Stroke ...

Posted on Jul 14, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Carberator is flooding on my still 38 fs why?


something in the needle and seat preventing the needle from sealing off
could be float adjustment or in this case needle to diaphragm adjustment

Jan 15, 2017 | Motorcycles

1 Answer

Float height of carberator please


you adjust it by bendng the small tab on the float that presses on the end of the float needle,to check it is right find a length of clear tubing and put it on the small pipe bit that is on the bottom of the float bowl ,then bend it around the carb and point it upward s,then undo the drain screw on the float bowl and the fuel will come up the pipe and when it stops that is the same level as the fuel in the float bowl.its usually about 2/3 of the way up the float bowl.to low and it can starve it of fuel and too high it will flood and leak out.

Dec 03, 2015 | Motorcycles

1 Answer

My powermate rear tine tiller is getting gas into the oil it will start and run as long as im am putting fuel into the carberator once i stop putting fuel the engine stops what is the problem. the til


This sounds like the float is sticking in the carb causing it to flood . You need to take the carb off and clean it and put a kit in adjusting the float per the instructions

Jun 27, 2014 | Powermate 18 in. 196 cc 4-Cycle Rear-Tine...

1 Answer

Gas continuously floods carberator


Fuel pump diaphragm faulty, main needle jet worn or float height needs adjustment.

Nov 13, 2012 | Craftsman Chainsaw 3.7 Vintage

1 Answer

Model 42a707 engine spitting gas out of carberator


Fuel needle leaking in the carb, remove the float bowl, check the float is moving freely, clean away any dirt, if no better replace the inlet needle.

May 06, 2012 | Yard Machines Garden

1 Answer

Carb float on a 1988 hondahurricane


With the float installed turn the carb upside down so the float is pointing up adjust the tab until you see the underside of the float is parrellel to the carberator's metal flat body section. This setting will provide the proper fuel level in the carb providing the proper maintained level of fuel for performance around tight turns as well as idling.

Mar 25, 2010 | 1987 Honda CBR 1000 F

1 Answer

Generac 4000xl carberator keeps flooding, engine is a gn220 when its is running it starts to soot up like it is getting to much fuel I have tried everything I could think of and cannot get it to quiet...


You have a problem with the carb float valve. It is no longer sealing causing fuel to continue to flow into the float bowl after it is full. It may be dirty, out of adjustment or just need to be replaced because old and worn out.

Nov 19, 2009 | Guardian Electrical Supplies

1 Answer

The carberator is causing gas wash on cylinders


Yes it is either the float is sticking or the float lever is set to low so as not to shut off the gas. Hope this helps. donnyb60

Mar 20, 2009 | Garden

Not finding what you are looking for?
1996 Suzuki GSX 750 F (Katana) Logo

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...