Question about kawasaki Zephyr 750 Motorcycles
You can replace the oil sending unit and get a mechanical guage to test oil pressure. oil pump never if ever fail.
Posted on Apr 27, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The throttle position sensor may be misaligned. This tells the computer how much throttle is being applied, and when they go bad, or come out of alignment, the idle tends to get up there. If that's not the issue, remove your air cleaner, the housing and everything until you get to the MAP sensor. Give it a good spray with carb cleaner, let it dry and replace the air cleaner with a new one. If the MAP sensor detects minimal air flow, the computer jacks up the idle to compensate.
Posted on Nov 07, 2008
i think it means that you have a turn signal bulb that needs replacing cause its not working. check turn signals and see if they are blinking properly from front & rear of vehicle.
Posted on Mar 16, 2009
This is a classic symptom of a bad mass airflow sensor. Nissan designed this as a protective feature on the car. If the mass air sensor goes bad, the computer limits the car to a 2400RPM rev limit to prevent damage.
The sensor is under the center nose panel between the headlights. Take that off and on the back of the airbox (which fills this space) you'll see a pipe coming out that meets at a "T" with another hose going across and down under the headlights. That pipe off the back of the airbox is the mass air sensor (it has a harness plugged in).
Posted on Mar 27, 2009
you can try taking the positive cable off for about 3-secs and check in you owner manual to see if it tell you how and if you do have one try this website www.edmunds.com to see if you can download one for you car.
Posted on May 25, 2009
The oil pump is in the the oil pan so you will need a new oil pan gasket and some form a gasket as well to put the pan back on, because you will have to take it off, you will see the oil pump a soon as you take the pan off, it will have a tube connecting to the pick up screen and to the block, remove bolts from the block and remove oil pump. be prepared the primming rod will probably come out too. itll need to go back of course, make sure seated in correctly because the primming rod runs off the cam. make sure the surface area for the oil pump gasket is clean before reinstalling new oil pump same goes for oil pan. after everything back together refill oil. It is best to test the oil pump before starting for your engine. the best way to do this is to remove the distrubuter if it has one if it has electronic ignition it will have a cap where the distributer went remove that and you will see the top end of the primming rod, fit appropriate socket on the primming rod and use a battery gun to spin, look inside oil fill cap and make sure you see oil flow or oil pressure on your gage if equiped, CAREFULL!!!!!! make sure the socket on battery gun has no way of falling off, or you will have to remove oil pan again to retrieve it.
Another way to prime pump is to disable igniton main power like remove the coil wire, or main power wire for electronic igniton so you can turn the motor over with out it starting, once again turn it over until you know you have oil pressure with the gage or through oil fill cap. put ignition back together start the car and once again confirm oil pressure. If every thing looks good your done Good luck
Posted on Mar 20, 2010
Tips for a great answer:
Aug 21, 2014 | Cars & Trucks
Apr 22, 2014 | 2002 Ford Escort
Apr 19, 2017 | 1997 Dodge Intrepid
Sep 03, 2010 | 1997 Chrysler Concorde
Nov 17, 2009 | 2002 Honda Civic
Jul 10, 2009 | 1997 Jeep Wrangler
May 05, 2009 | 2005 Bajaj Pulsar 150
Jul 13, 2017 | 1996 Chevrolet Blazer
68 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: