Question about Power Motorcycles

1 Answer

96 seadoo xp idles good but loses power when advancing the throttle.already got carb kits what else could it be

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 271 Answers

Poor ignition, timing. Have you done a compression test to be sure it's all good to go internally?

Posted on Apr 26, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 159 Answers

SOURCE: yamaha yzf750r missfire rough running

Try taking air cleaner off before going to far, Blow carbies with air, dont use full force I done this to mine and it fixed it you may be lucky dirty jets.

Posted on Jan 10, 2010

  • 3567 Answers

SOURCE: wont idle unless i havethe throttle barley turned

The idle circuit is still plugged up or it would not be giving you this problem. Remove the carb and dis-assemble it then soak the parts in denatured alcohol for 30 minutes. Then use a spray carb cleaner to finish the job. Spray into all the little holes in the carb body. Especially spray into the air screw and throttle screw holes. Reassemble the carb and LIGHTLY seat the air and throttle screws then turn each of them one and one half turns outward. This is the factory setting. Before putting the slide back into the top of the carb, move the clip on the jet needle one notch lower on the needle. This will richen the low end fuel mix. Install a new spark plug and clean the air filter. Please rate my answer. Thanks.

Posted on Feb 09, 2010

  • 4 Answers

SOURCE: won't idle without choke, turn throttle boggs out

have u checked the float hight on the carburator? also make sure ur choke curcuit i clean and free of dirt

Posted on Apr 14, 2010

  • 653 Answers

SOURCE: engine revs up while idling

Any stuck cables or jets or vacuum hose leak?

Posted on Apr 26, 2010

tunde007
  • 2382 Answers

SOURCE: i have a yamaha terrapro that idles fine and runs

Hi, the elements of internal combustion engines are: correct fuel/air ratio, spark at right time, adequate cylinder compression.
There are many passageways and openings to check and clean. All are important in function and when obstructed or not working properly, have subtle to radical effects on engine performance. Vacuum leaks and carburetor synchronization also have effects on performance and should be inspected and adjusted following the below procedures.
Carb Cleaning 101 Warning: Remove all rubber parts before you begin. These parts usually include vacuum diaphragms, needle valves, o'rings, hoses, and other parts. Spray cleaners will damage these parts. Do not disassemble individual carbs from the carb bracket.
Air & Fuel Passageways: Trace and learn individual fuel and air circuits from beginning to end. Machines can only drill straight through the cast passageways. To change direction, another angled passageway must be drilled. The union is plugged with a brass or bronze bead. Inspect and clean each passageway with spray cleaner, brushes/pipe cleaners/etc, and compressed air. Remove any discoloration and debris. Look for spray cleaner to exit from one or more passageways.
Jet Cleaning: Inspect jets by holding to light and look through them. You should see an unobstructed round hole. Clean the jets with one or more of the following: jet cleaning wires, soak solutions, carb spray cleaners and compressed air. Re-inspect jets after cleaning and install when clear of obstructions. Some main jets have paper-like gaskets. Most have metal spacers between the jet and the emulsion tube. Some screw directly into a brass emulsion tube which is machined for a 7mm wrench at its float chamber exposed base.
Inlet Fuel Valve: Inspect the needle valve & spring. Press down the tiny metal rod that protrudes from the **** or float end of the needle valve. The spring should move freely and return the rod to its location. Check the needle valve's seat area for a groove or other wear. It should appear highly polished. Some needle valve seats are rubber and wear may not be visible. Inspect the needle valve jet seat. You can clean the jet seat with Q-tips and semi-chrome polish if necessary.
Carb Body Castings: Blow air through the atmospheric vent holes located on the dome of each float bowl chamber. Air should exit via hoses or brass nipples. Inspect the emulsion tubes and passageways (cast towers that jets thread into) for discoloration and debris. Clean interior emulsion towers with a soft bristle gun cleaning brush. Clean each Venturi (main carb bore).
Needle Jets & Jet Needles: Clean the needle jets, jet needles, and passageway or tower that needle jet screws into. Clean the emulsion tube (pipe between needle jet and main jet) (Main Jet may screw into emulsion tube). Jet needles are part of the throttle slides. See below...
Throttle Slides: There are several types of throttle slides: Mechanical linkage, vacuum, diaphragm, and cable. Disassembling the jet needle from the slide is not always required for cleaning. If you have vacuum piston type throttle slides (large diameter solid metal slide), avoid cleaning the lubrication from sides and caps. If piston type check cap vents and passageways with air. Clean if necessary and re-lube. If you have rubber vacuum throttle diaphragms, inspect for dry-rot, defects, and tears by gently stretching rubber away from center. Do this until all areas around diaphragm have been inspected. Replace any defective part as described above. Clean carb body areas around diaphragm including air passageways and air jets. Diaphragms have a locator loop or tab fabricated into their sealing edge. Observe this locator upon reassembly. Avoid pinching the diaphragm when reinstalling caps.
Fuel Screws: Fuel screws have sharp tapered ends. Carefully turn one fuel screw in while counting the turns until it seats lightly. Warning: These screws are very easily damaged if over tightened into their seats. Record amount of "turns-in" and remove the fuel screw, spring, washer, and o'ring. The fuel screw is part of the enrichment (choke) circuit...clean passageways as described above. When carbs are assembled, spray low PSI compressed air into diaphragm air vents located at intake side of carbs. Throttle slides should rise, then fall when air is removed. Lightly lube external moving linkages. Reinstall carbs and follow through with carburetor synchronization.
Throttle Cables: Lubricate cables periodically. If cables are disconnected from carbs or removed for replacement, etc . . . remember cable routing and ensure proper reinstallation routing. Avoid bread-tying, sharp bends, and pinching cables. Adjust cables so throttle grip has about 5mm of play or throttle slides or butterfly valves may not open completely (full throttle)(wide full open).
Float Bowls: Inspect float bowls for sediment, gum or varnish, crystallization, and defects. Clean all pipes, tubes, passageways, and embedded jets with cleaners and compressed air. Remove and clean the drain screw and area. Inspect bowl gasket and replace if necessary. Clean and inspect overflow pipes and tubes, look for vertical cracks.
Floats: There are several types of float materials: plastic, brass, black composite, tin, and others. Handle floats carefully. Avoid bending, twisting, denting, or other means of mishandling. Most floats are adjustable by bending a small metal tab near the float axle end. Do not change the float adjuster tab unless tuning fuel service levels. Clean metal floats by soaking or by spraying cleaner and wiping clean. Other material type floats may require replacement if cleaning is necessary. Inspect the needle valve (float valve) and seat. Check needle valve's spring loaded pin. It should depress and return smoothly and without resistance. Check the needle valve's tip for a worn groove. Replace needle valve and seat if either symptom exists. These parts wear together and must be replaced as a set.
Choke Plungers: It is common for Mikuni slide carburetors to have indented or hardened choke plunger pads. If the pads are worn, indented or hardened with age, then the idle of your bike will vary wildly as the pads no longer seal well.
Synchronization: This is a fine adjustment performed usually and preferably with the carbs installed and the engine running. The unusual part is performed with gauged wire with the carbs on the work bench. Carburetor synchronizing balances Venturi vacuum at the exhaust side of each carburetor, resulting with smooth idling and optimized performance at all throttle openings. Synchronization is checked using a set of gauges which are either air vacuum type or liquid mercury type. The gauges are connected to vacuum ports on the intake manifolds via nipple tubes or if sealed with screws, sync gauge adapters will be needed. With the engine running at temperature, and with a fan or means of forced convection aimed onto the engine, the carbs fuel screws and idle are adjusted, then the synchronization is adjusted via adjustment screws on the carbs. A reserve fuel tank is recommended for convenience of accessing carbs during this procedure. See gauge instructions and repair manuals for detailed use of synchronization gauges.
Notes: While carbs are apart, record the jet sizes. Look for a very small number imprinted on the body of the jets. Verify that numbers are the same for all jets on models with in-line cylinders. A few transverse-4 models and V-engines, the inner and outer carbs use some different size jets and it's important to not mix them up. If you have dial or verneer calipers, measure and record float heights. Perform measurements with floats just touching needle valves, though not depressing the needle valve rods. Replace fuel and vacuum hoses. Be sure to use fuel rated hose for fuel. Install or replace in-line fuel filters. It's a good time to remove and clean interior petcock fuel filters. Inspect carb manifolds for dry-rotting, inspect all clamps and air ducts. Inspect, clean, lube, and/or replace air filter(s).

Posted on Nov 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 1995 seadoo bombardier shut completely down while wide open


Very likely a cracked wire on the ignition-advance. As the throttle is advanced so is an advance-lever that causes the wiring attached to it to Flex, causing an intermittant loss of current to the coil/CDI.
The flywheel may have to be removed to repair/replace the wiring.

Aug 16, 2014 | Tempest SeaDoo/Sea-Doo/Bombardier Jet Ski...

1 Answer

What causes a 1993 seadoo engine to bog down then take off, then bog down?


fuel mixing issue. A good tune up is recommended. Focus on the carburetor.

Jun 07, 2014 | Sea-Doo US Seadoo Sea doo pump off 1993 XP...

1 Answer

Once bike gets over 3000 it sticks there. (hanging idle)


Probably the vacumn slides are hanging up, Not because they are stuck, But because the idle screw is set too high to get to idle. The idle will usually hang up at 3,000 rpms. Set the idle mixtures at 1 1/4 turns out & make sure the throttle cable has play. Now back the carb idle down till it just idles about 1,100 rpms. with choke off. If the carb sync is way off, I will hang up on 1 carb when hot. You need a vacumn guage set to make sure they are balanced. To check the spark advance (which I doubt), Put a timing light on the LH plug wire & shine it at the timing marks behaind the LH cover on motor at botton covering the generator. It should be on the F marks at idle & at the unmarked line aprox 1 " over which is full advanced when reved up to 1/2 throttle. But yes a air leak at the intake manifold could cause it to rev, But will be a very erratic idle at 1,100 rpms. If the idle circuits are working correctly, You should be able to kill each cylinder with turning in the mixture screws one at a time. That checks the idle jet circuits.

Mar 26, 2014 | 1977 Yamaha XS 650 D

1 Answer

96 seaboo will not go full speed in water, but full rpm out of water


carbs need cleaning and check the pulse jet that squirts fuel on set off , fuel pump diaphrams ok ?

Sep 08, 2013 | Sea-Doo US Seadoo sea doo cdi ignition...

1 Answer

My 1996 Seadoo xp, one of the carb's flaps is


either run it and spray carb cleaner into it (idled up a little) or start adding good in tank cleaner to fuel.

Jul 09, 2011 | Boating

1 Answer

Hi, I own a Pulsar 150 DTSi (2007). I want to know the correct/most effective technique for setting the idling speed and carburetor volume control screw setting. I have already read many articles on the...


First and formost make sure air filter is clean.Then start bike and warm up engine.with engine warm adjust idle screw(the big screw with spring around it)Turn clockwise to increase and counterclock wise to decrease.with bike idling properly the low speed air adjustment screw (small screw located just above fuel bowl on side of carb)Adjust in small increments 1/16 turns at a time till bike has smooth throttle responce.This screw contols air flow during idle and up to 1/4 throttle.From 1/4 throttle and up the needle setting on plunger inside of carb takes care of 1/4 and up.You usally dont have to mess with needle unless you do upgrades to get more power out of bike.But over time the low speed settings can change due to wear on idle needle and air needle.So thats why you have to make adjustments.If bike still dosent respond or idle correctly I would purchase carb rebuild kit and your problem will be solved.

Mar 21, 2011 | 2007 Bajaj Pulsar 150

1 Answer

Sea doo jet ski won't get full throttle. It idles fine but once you hot gas it regarding up and down


I am not sure of the model that you have,so its a bit hard to help.If you have a seadoo and you want great help,I would go to seadooforum.Its the best site with really good,and also total knowledge of all things Seadoo.I have one also.The help is unsurpassed.I have a seadoo also.Hope this helps you

Feb 03, 2010 | Sport & Outdoor - Others

3 Answers

Motor chokes and misses under moderate load and loses power


Sounds to me as tho it might need a carburetor adjustment, providing there is an adjustment screw on the carb. Sounds like the engine is running a bit lean. Did this problem occur right after the carb cleaning, or was it there in advance? Is there a fuel filter that might be clogged?

Jan 18, 2010 | Craftsman 20 hp 42 in. Deck Lawn Tractor -...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Power Experts

D. E. Hev

Level 3 Expert

1173 Answers

mikeuk

Level 2 Expert

70 Answers

Lawrence Oravetz

Level 3 Expert

9742 Answers

Are you a Power Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...