Question about kawasaki Motorcycles

1 Answer

How do i remove seats on a 1987. Kawasaki zx10 when the lock cable has snapped, need to charge battery. Ta

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 428 Answers

Howdie you will have to drop it out from the bottom very carefully don,t tip it over will cause Leakage or go to the Dealer HAnd them a 20 and Be NICE to them for imfo to help ya out thks again for your time

Posted on Apr 25, 2015


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 9 Answers

SOURCE: Yamaha Virago XV700 - 1987 Seat Removal

Most Yamaha models have 2 bolts holding the seat on, usually located between the top shock mounts and the side covers. You should be able to find them without too much trouble, but remember- they are metric. Hope this helps.

Posted on Jan 21, 2009

  • 850 Answers

SOURCE: Charge point for 2005 FLSTNI

buy a battery trickle charger [ebay has them]they have a setup for just that purpose & it maintains the battery at a premuim level
thus extending its life span & no more hard starting dramas
cheers Rob

Posted on Aug 15, 2009

  • 89 Answers

SOURCE: how do i remove the seat on a honda 954 rr 2002?

I think on this model you just pull up on the back corners of the riders seat to expose 2 retaining bolts. Remove the bolts then pull the seat up and back to remove it.

Posted on Dec 29, 2009

  • 152 Answers


Under the tail light is a lever pull out on it and lift the back of seat

Posted on Dec 11, 2010

  • 1 Answer

SOURCE: need to remove battery so I can charge it on a 2008 Kawasaki Ninj

  1. Undo the screws on the plastic fairings, and then pull them off. They are stuck in with some tabs but should pull off easy when you undo the screws.
  2. Use an allen key to take off the 2 other screws on each side of the seat.
  3. You now should be able to see the battery now but need to get the cover off. Theres one screw in the middle towards the back that you need to take off. Pull the fuses off gently to get them out of your way.
  4. Now you should be able to get to the battery.

Posted on Dec 25, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why would my bike that's a Kawasaki zx10 backfire? Is it because of my carburetors and what would the settings be? please help

Hi, Francois and the usual suspects are:
1. A severely drained battery.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Faulty main circuit breaker and or connections.
4. Faulty ignition coil and or connections.
5. Faulty spark plug, oil or gas fouled, wrong heat range or service type, wrong gap, loose in the cylinder head, broken electrode or insulator.
6. Faulty spark plug cables, leaking or broken, internal damage.
7. Faulty ignition module, switch, CKP, MAP, CMP, sensor and or any connector in the ignition circuit could have corroded, loose, or broken pins/sockets
8. Burnt exhaust valve or air leak in the exhaust system.
For more information about your issue, please visit the websites below. Good luck and have a nice day.
05 zx10 backfiring issue Kawasaki ZX 10R net
Parts Diagrams Kawasaki Vehicle Models

Jan 03, 2016 | kawasaki Motorcycles

1 Answer

Has anyone a workshop manual Kawasaki GPZ1000RX english

There's a Haynes manual for this bike - see for example here
it won't be free. tO GET THE LINK INSERT E WHERE YOU SEE A *

Is this ebook in English ?

or try this perhaps
I hope these are helpful. You should say where you are for (possibly) more helpful information.

I'm sorry, I could not find a free one.


Dec 23, 2014 | 1987 kawasaki GPz 1000 RX

1 Answer

Battery removal

is there a strap or clamp securing it ?

Jan 18, 2014 | 2008 kawasaki ZX-10R

1 Answer

How do i remove the drivers seat on a 2008 zx10

Remove the two small panels under the seat. Then remove the screw in center holding seat in place.

Apr 16, 2012 | 2008 kawasaki Ninja ZX10R

1 Answer

I instaled new clutch plates in my zx10 and I don't have any motion

Excuse the silly question, but do you by any chance have any springs laying around the shop floor that you maybe forgot to put back in?
The other possibility is your clutch cable is too tight and needs to be backed off, or is simply incorrectly seated.

Mar 15, 2011 | 2007 kawasaki ZX-10R

1 Answer

Remove seat ZX10?

take the side fairings off and there are two bolts you'll need to back out. one bolt on each side

Jan 16, 2011 | 1989 kawasaki ZX 10

1 Answer

Hi where is the fuse box on my 1989 zx10 kawasaki

take side fairings off. remove two bolts on seat one on each side. fuse box under sea

Dec 05, 2010 | 1989 kawasaki ZX 10

1 Answer

How do you cahrge the battery on a kawasaki zx14 ninja?

What you would do is take the seat off, usually you have a key lock under the seat. Then what you wanna do is take off the positive battery cable off the battery and hook up a battery charger. If you don't have a battery charger take the battery completely out and take it to autozone or what ever auto dealer you have near by, and they will charge the battery for no charge. Finally you take your battery and put the terminals back on make sure you have the cables on right, also what ever you do don't charge the battery while its hooked up to the bike. If this was useful information plz rate me. Thank you.

Aug 20, 2010 | 2006 kawasaki ZX-14

2 Answers

1987 kawasaki ninja zx10 wont stay running when warmed up it

you didnt mention anything to do with the carbs so try some "Sea foam".... purchase at Autozone ($10) pour 1/3 can to two gallons fuel and drive it around for a good 10 to 15 miles and get on it once in awhile, ride safe..if the carbs are dirty or clogged... they wont be after your ride..there might be a little hesitation your first couple of miles till it starts to took my bike 10 miles before it cleared out..bump start your bike if you have to to get it going and keep it going till it clears up.

Apr 08, 2010 | 1989 kawasaki ZX 10

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

76846 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides