Question about Goes Motorcycles

1 Answer

Engine runs as long as i hold the start button and goes dead when i realease it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Goes Master
  • 991 Answers

With ignition on check wiring for power to coil. I think that you are only getting power to coil through the starter circuit and not the ignition circuit.

Posted on Apr 25, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced starter in 99 Saturn. Battery went dead, got new one ...same thing. REPLACED ALT. SAME THING. Had alt tested, it was good. Wont hold a charge, wont start. Could starter wires be crossed?


Instead of guessing (could wires be crossed ) Testing the electrical circuits is the way to find the problem . Battery goes dead when ? over night ,while driving the vehicle ? If it goes dead overnight you have a parasitic drain on the electrical system . Look at a wiring diagram an check the wires for correct hook up . Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. Year , make , model an engine size . under system click engine then under subsystem click starting . Click the search button ,then the blue link . Really don't think you could cross the wire's ,only two size wires (connectors ) . only hooks up one way.

The BEST Way TO Perform Parasitic Draw Test

How to voltage drop test starter motor circuit
If you can't find the problem after viewing these videos your best bet , take it to a qualified repair shop.

Jun 18, 2017 | Cars & Trucks

1 Answer

Cbr 600 f4i year 2002 will start but after running


Maybe electrical. Use an inline spark tester on one of the outside cylinders. Check to see if spark stops after start button is released. If so it seems that something is getting powered when the start circuit is activated but not powered in the run circuit. The cdi box or pulser coils are suspect.

Sep 01, 2014 | Motorcycles

1 Answer

Dash board goes dead


1) check and see if your car has a good earthing cable.
20 it could be a loose terminal or fuse.

Mar 15, 2014 | Winnebago 2008 Voyage 32H

1 Answer

Car goes dead while driving starts right back up


the sock on the bottom of your fuel pump is dirty replace the assy and fuel filter

May 02, 2013 | 1991-1993 Chevrolet Lumina Radiator w/ V6...

1 Answer

Try to ignite pilot on 15/30b. flame ignites but goes out immediately when i realease the green button after 20 seconds. have replaced thermocouple but still no joy - any ideas ?


First, I'm assuming you have a residential Gas-Fired Heater or Water Heater that you are having problems with. My answer is based on this assumption.

Most thermocouples require that you hold the button for at least 45 seconds. Try holding the button for 60 seconds prior to releasing it. If this does not work, you can test your new thermocouple if you have a multimeter...preferably one with an alligator clip for your leads. To test your thermocouple, disconnect the end that screws into your gas valve. Set your multimeter to read Milivolts. Put your red lead on the copper line of the thermocouple.....it's easier if you have an alligator clip. With your pilot lit, hold down the button for 45 seconds and continue to hold while you put the black lead of your tester on the very end of the thermocouple (the part that attaches to the gas valve). You should read a minimum of 12 milivolts. If you do not read 12 milivolts, your new thermocouple is bad. If you are reading 12 milivolts, screw it back into the gas valve, relight, hold the button for minimum 45 seconds. Release the button. If the pilot goes out immediately, the problem (>99% probability) is with your gas valve.

Mar 06, 2010 | Heating & Cooling

1 Answer

Car goes completely dead. Drove car for a while and after a short stop at the post office tried to start the car but completely dead. After about 10 minutes car it regained electrical and started again....


does goes completely dead mean it stops running while going down the steet or maybe only when you come to a stoplight? if it runs ok and just will not start as it sounds when you return after a short period of parking it.there are several oter things unclear.when you turn the key to start it do you hear the usual sounds like the engine is turning but it just wont run=one issue.if you hear nothing at all= dead baterry, loose connection in the wiring, bad starter. it sounds like the starter is working but the engine will not run.this could be a problem with the ignition system= computersystems =crank sensor. or fuel supply problems. nothins easy anymore. sorry.

Feb 21, 2010 | 2001 Volvo V70

1 Answer

The car goes dead after 5 min.


start engine and hold rpm about 1500 turn all light on and wipers heated rear windows the lot ,if engine stops the altenator is U/S if it all keeps working and engine running change the battery

Jan 23, 2009 | 1998 Ford Contour

1 Answer

Dryer not working


the button you push is a momentary start switch.whats suppose to happen is the power passes thru the push to start switch for a moment till the motor centrifugal switch goes to the run winding.what i have found happening is a lint buildup in the motor switch area dose not allow the motor centrifugal switch to reset to the start winding when the dryer has finished the last load.so its trying too start on the run winding and it could only do that if you helped by spinning the drum while hold the start switch.soooooo.... unplug unit .get to the motor and vacuum it out.inspect your wiring for burnt/loose connections.if all is well and vacuuming did not solve problem.your motor may have an open start winding which you could check with an ohm meter.if you need any more help you can make an request thru fixya email. God bless ,tom

Jan 22, 2009 | Hotpoint TDC32 Electric Dryer

1 Answer

Sandisk c250


To access Recovery Mode:
-Make sure the player is off (if necessary, hold down the power button
for 20 seconds to turn it off)
-Move the hold switch to ON (move to the right towards the record
button).
-Hold the record button.
-Connect the player to the computer.
-Keep holding the record button till the "new hardware is ready for
use"
comes up, then realease the record button.

Dec 07, 2007 | SanDisk Sansa c250 (2 GB) MP3 Player...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goes Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Brad Brown

Level 3 Expert

15557 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Goes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...