Question about kawasaki Motorcycles

1 Answer

OK I've adjusted my Carb on my Kawasaki bayou 300 and now in order for it to run like it should the chock has to be on all the time. I can't figured this out......

OK I've ajusted my Carb on my Kawasaki bayou 300 and now in order for it to run like it should the chock has to be on all the time.Damn I can't figured this out......

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • kawasaki Master
  • 3,519 Answers

Hi Abbott:
Sounds like you've almost got it! Way to go.
Odds are pretty good that the jet(s) in the carb have some gummy bits in them. I'd be considering removing the carb, dismantling it, cleaning all the bits, using compressed air to blow it all out, re-assembling it, and having another go at it.
Since it only wants to run when you choke it, it's way too lean, so needs more fuel. Somethings gotta be plugged up.

Posted on Apr 25, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3567 Answers

SOURCE: kawasaki 300 bayou won't rev up.

No guarantees but try this. Pull the slide from the throat of the carb. Now move the clip on the jet needle down one notch. This will richen the low end mix. Two notches may be needed but do one notch at the start.

Posted on Apr 30, 2009

ollie reece
  • 1167 Answers

SOURCE: Bayou 300 cranks then stops after a minute

ok buddy to stop the back firing on the carb will be a screw turn this in 1/4 of a turn and try this the mixture screw on pic below

Posted on Sep 18, 2009

ollie reece
  • 1167 Answers

SOURCE: Kawasaki bayou 300 will idle ob but will not rev up

try playing with the mixture screw on the carbs this pic below will help you buddy get back to me if no difference7fe98b2.jpg

Posted on Sep 29, 2009

  • 124 Answers

SOURCE: 1987 kawasaki 185 bayou reverse light

No, the reverse light is only for reverse indication. If the light is coming on while riding in any forward gear there is a loose connection, probably where the reverse sender attaches to the transmission or the sender itself is malfunctioning.

Posted on Nov 23, 2009

  • 1 Answer

SOURCE: how do I adjust the valves on 2001 kawasaki 300

how do i adjust the vaulves

Posted on Feb 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kawasaki bayou 300 starter spins but wont engage all the time


The larger idler gear ring was spinning but not spinning the entire gear. I couldn't figure ... Starter Idle Gear Limiter Kawasaki Bayou 220 250 39076 1060 ' eBay ... kawasaki bayou 300 starter will not engage.

Mar 21, 2017 | kawasaki Motorcycles

1 Answer

Kawaski bayou 300 stater wont engage engine all the time why


Hi, Gary you may have a starter solenoid or starter drive going south for more information about your issue and free downloads that you will need please visit the websites below. Good luck and have a nice day.
bayou 300 starting problem Kawasaki ATV Forum
1986 Kawasaki Bayou 300 Starting Issues
Kawasaki Bayou not starting
Owner Manuals Service Manuals Kawasaki Vehicles

Jan 25, 2016 | Motorcycles

1 Answer

I have a 90 Kawasaki KLF300 Bayou 4X4 and I am having a problem with it running too rich no matter what I do. I have taken the carb apart several times, reset the mixture screw to factory setting. I have...


Hey Dave,
thought I answered this already,,,??? Classic "brass kit" symptom! >>> You need a "brass kit".. this is the needle jet and the jet needle in the center of the carb. The jet needle is the thin needle that hangs down from the center of the slide... The needle jet is the "hole" that the jet needle slides into...Remove the carb, take the bowl off, remove the main jet, the needle jet holder should be able to be gently tapped out, the needle jet is a short brasspiece,, it comes out through the hole where the slide goes,,, reinstall the NEW needle jet, needle jet holder...(it may have a groove in it for correct location). once its seated, you can reinstall the main jet..NOW >> to install a new jet needle,,, remove the slide from the carb.. remove the spring and seat from the slide that holds the needle jet in place.. NOTE which groove the clip is in on the old needle.... (should be the middle one). re install the new needle, reinstall everything else and your atv WILL run fine for a long time..This is a common problem on ATV's..
you need part #'s
1990 Kawasaki BAYOU 300 4X4 KLF300 C2 Carburetor

http://www.kawasakipartshouse.com/oemparts/p/kawasaki/16009-1503/needle-jet-n36w

http://www.kawasakipartshouse.com/oemparts/p/kawasaki/16017-1270/jet-needle-6

Jun 24, 2017 | kawasaki 2004 Bayou 300 4x4

1 Answer

I have a 88' Kawasaki Bayou 300. It will start


buy a bottle of gasline anti-freeze. it will absorb any water in your fuel. add a half a bottle now and a half next time you fill the tank. should improve the operation of the engine

Jul 13, 2010 | kawasaki Full Suspension Mountain Bike Men

1 Answer

Bayou 300 cranks then stops after a minute


ok buddy to stop the back firing on the carb will be a screw turn this in 1/4 of a turn and try this the mixture screw on pic below

Sep 18, 2009 | 2001 kawasaki KLX 300

2 Answers

Kawasaki 300 bayou won't rev up.


No guarantees but try this. Pull the slide from the throat of the carb. Now move the clip on the jet needle down one notch. This will richen the low end mix. Two notches may be needed but do one notch at the start.

Apr 30, 2009 | 1990 kawasaki ZXR 400

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...