Question about Motorcycles

1 Answer

Bleed rear brakes procedure on 2004 rune - Motorcycles

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Motorcycles Master
  • 503 Answers

Hi fill the resivour with clean fluid open the bleed nipple and allow to flow for a few minuets. After this close the nipple and pump pedal slowly 3-4 times on the last pump hold it down and open the nipple. Then before you start pumping close the nipple again and repeat the process. Keep this going until pedal is firm. Regards Jim...

Posted on Apr 14, 2015

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 126 Answers

SOURCE: What is the proper procedure to bleed the air out

The one man way is to get a small botle( a spice bottle and fill it about a third of the way up. Place a piece of tube (clear preferably)of the proper dimension over your bleeder valve located on caliper. Then open bleed valve and presson brake pedal. If all bubbles escaped thru tube into bottle, then you may repeat untilno bublesremain then tighten bleeder valve. If bubbles remain in hose, close bleeder before releasing brake. This will probably require an assistant. Ensure you keep reservoir from going dry by filling when necessary. Repeat as necessry until all bubbles are gone from brakelines.

Posted on Aug 21, 2009

  • 8909 Answers

SOURCE: i have a problem with

Strip the rear brage down and clean the corrosion from the moving parts. Lubricate ONLY the metal moving parts with CopperEase taking care not to contaminate the rubber seals and internal brake parts.
Reassemble fill and bleed the system with fresh brake fluid and road test.

Posted on Jan 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brakes went out,master cylinder is dry. filled the master cylinder pumped brakes and bled rear drivers side


    If there is a substantial fluid eruption, there are air bubbles still trapped in the system. You must repeat the bleeding procedure to remove that air. A modest disturbance in the fluid returning to the reservoir indicates a properly bled brakesystem.

    How To: Bleed Your Brakes - Feature - Car and Driver

    www.caranddriver.com/.../how-to-bleed-your-brakes-feature Car and Driver
Feedback

How To: Bleed Your Brakes - Feature - Car and Driver

www.caranddriver.com > Features

Car and DriverIf there is a substantial fluid eruption, there are air bubbles still trapped in the system. You must repeat the bleeding procedure to remove that air. A modest disturbance in the fluid returning to the reservoir indicates a properly bled brake system.

How to Bleed Brakes - Tips on Bleeding Brakes

Jan 01, 2016 | Cars & Trucks

1 Answer

1990 jeep wrangler bleeding breaks


Hi there:
I suggest to check this procedure, when the hydraulic brake system must be bled whenever a fluid line has been disconnected because air gets into the system.

A leak in the system may sometimes be indicated by a spongy brake pedal. Air trapped in the system is compressible and does not permit the pressure applied to the brake pedal to be transmitted solidly through the brakes. The system must be absolutely free from air at all times. If the master cylinder has been overhauled or a new cylinder has been installed, bleed the cylinder on a bench before installation. When bleeding brakes, bleed at the wheel most distant from the master cylinder first, the next most distant second, and so on. During the bleeding operation the master cylinder must be kept at least 3 / 4 full of brake fluid.


The ABS bleeding procedure is different from the conventional method. It consists of the following three steps:
Step 1: Conventional manual brake bleed.
Step 2: Bleeding the system using the DRB scan tool.
Step 3: An additional conventional manual brake bleed.

The recommended ABS bleeding procedure is as follows:
  1. To bleed the brakes, first carefully clean all dirt from around the master cylinder filler cap. Remove the filler cap and fill the master cylinder with DOT 3 brake fluid to the lower edge of the filler neck.
  2. Bleed the master cylinder first. Have a helper operate the brake pedal while bleeding each master cylinder fluid outlet line. Do not allow the master cylinder to to run out of fluid,as this will allow additional air to be drawn into the cylinder.
  3. Bleed the brake system in the following sequence:
    1. Master cylinder
    2. HCU valve body (at fluid lines)
    3. Right rear wheel
    4. Left rear wheel
    5. Right front wheel
    6. Left front wheel
  4. Clean off the bleeder connections at all four wheel cylinders. Attach the bleeder hose to the right rear wheel cylinder bleeder screw and place the end of the tube in a glass jar, submerged in brake fluid.
  5. Open the bleeder valve 1/2 - 3/4 of a turn.
  6. Have an assistant depress the brake pedal slowly and allow it to return. Continue this pumping action to force any air out of the system. When bubbles cease to appear at the end of the bleeder hose, close the bleeder valve and remove the hose.
  7. Check the level of fluid in the master cylinder reservoir and replenish as necessary.
  8. After the bleeding operation at each wheel cylinder has been completed, fill the master cylinder reservoir and replace the filler plug.

Do not reuse the fluid which has been removed from the lines through the bleeding process because it contains air bubbles and dirt.


  1. Perform the "Bleed Brake'' procedure with the DRB II scan tool. This procedure is described in the DRB II software information and diagnostic guide.
    1. Attach the DRB II scan tool to the diagnostic connector.
    2. Run the Bleed Brake procedure as described in the DRB II tester guide.
  2. Repeat the conventional bleeding procedure as previously outlined.
  3. Fill the master cylinder reservoir to the proper level.
  4. Check the brake operation.


Hope this helps.

Apr 21, 2013 | Jeep Wrangler Cars & Trucks

2 Answers

I have a 2004 Land cruiser and changed the right rear brake cyl and brake shoes . What is the proper procedure to bleed the rear brake system. Thank you for your help.


  1. Check the fluid level in the reservoir after bleeding each wheel. Add DOT3 fluid, if necessary.
  2. If the master cylinder was disassembled or if the reservoir becomes empty, bleed the air from the master cylinder as follows:
    1. Disconnect the brake lines from the master cylinder.
    2. Slowly depress the brake pedal and hold it.
    3. Block off the outlet plug with your finger, and release the brake pedal.
    4. Repeat 3 or 4 times.

  3. Bleed the brake starting with the one furthest from the reservoir and then the next furthest, etc.
  4. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
  5. At the point when fluid stops coming out, tighten the bleeder plug to 11 Nm (8 ft. lbs.), then release the brake pedal.
  6. Repeat until all the air in the fluid has been bled out.
  7. Repeat the procedure to bleed the air out of brake line for each wheel.
  8. Check the fluid level and add DOT3 fluid if necessary.

Aug 07, 2011 | 2004 Toyota Land Cruiser

2 Answers

I have a problem with de rear brake, if i runing and put de rear brake to stop they closed de pads and not runing again the tire not moving


Hello,

It sounds to me like the Brake Calipers need to be rebuilt due to the sticking problem you have described. You can try bleeding your brakes, but I'm pretty sure it's the calipers.

If you find this information helpful, please vote on this post. Thank You.

Regards,

Oz

Jan 11, 2011 | 1999 Honda GL 1500 SE Gold Wing

1 Answer

Need help bleeding brakes 2004 ford explorer


To bleed the brakes 1st make sure the fuild level is full ,and you will need a assistant . have your assistant pump the brake petal three to four times then hold presure on petal (pushing down ) then open the bleeder valve on the left rear caliper ,have assistant push petal towards the floor until it stops and then hold it there until you close the bleeder valve ,then repeat process four to five time recheck brake fulid level then repeat same process on right rear caliper next go to right front and end on left front ,keep a eye on the fuild level so that it is not allowed to run out or you will have to start over again ,there is no speical procedure ,any other questions just ask

Dec 29, 2010 | 2004 Ford Explorer

1 Answer

I changed the front brake lines on my 2004 dodge ram 1500, 4.7 liter, 2WD. do i need to bleed all four brakes?


Yes. It's easy to get air into the other lines. It's also a good time to make sure you have good, new brake fluid. If you didn't already, **** out the stuff in the reservoir and fill it with new, clean stuff. Now, go to your local auto parts store and get a one man brake bleeder, if you don't have one. It's a huge time saver. Starting with the rear passenger wheel, bleed it until you get new, clean fluid. Keep an eye on the reservoir and don't let it get low or you'll get air in and have to start over. Move on to the rear drivers wheel, and repeat the procedure. Next is the front passenger wheel, and last is the front driver's side wheel. Now you will have clean, new fluid in all 4 brakes, and an air-free system.

Nov 19, 2010 | 2004 Dodge Ram 1500

1 Answer

I am working on a 2004 dodge caravan with a soft brake problem.i have replaced the rear shoes and adjusted rear brakes,also replaced front rotors and pads.i have also replaced the master cylinder.after...


try bleeding the master cylinder at the lines first as it indicates that there is still air in the pistons
loosen one line at a time and gently apply the brakes until any air bubbles come out tighten the line before releasing the brake pedal
do it for the other line and then bleed all the brakes starting at the longest line first and ending at the shortest line

Apr 23, 2017 | Dodge Challenger Cars & Trucks

1 Answer

Video for replacing front brakes pads and rotors on a 2004 ford e


Hello,
ccr20011001bb00.jpg Brake Bleeding
Purging air and moisture from your binders
CarCare - Maintenance - Brakes

ccr20030701as00.jpg ABS Speed Sensor Service
A clean sensor is a happy sensor
CarCare - Maintenance - Brakes

ccr20030701db00.jpg Drum Brakes - Rear Brake Drum Adjustment
It's stupid not to adjust your rear drum brakes
CarCare - Maintenance - Brakes

ccr20050201rr00.jpg Replacement Rotors
Friction, brake rotors, and you
CarCare - Maintenance - Brakes

ccr20050501pb00.jpg Power-Bleeding Brake Systems
Air today, gone tomorrow
CarCare - Maintenance - Brakes

ccr20050701bp00.jpg Replacing Brake Pads
How to replace worn pads
CarCare - Maintenance - Brakes

ccr20071101bs00.jpg Bleeding Power Steering
Getting rid of that air in there
CarCare - Maintenance - BrakesThanks

May 29, 2010 | 2004 Ford Escape

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...