Question about Motorcycles

1 Answer

Rebuilt my banshee motor/carbs it starts but wont stay on when you hit the throttle it boggs down and shuts off also one side is getting hot the other stays cold newplugs newgas newjets help please

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 141 Answers

You are getting to much air.
also you need to check your crank bearings.
could be getting xtra air there.

Posted on Jun 09, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 33 Answers

SOURCE: banshee wont rev

Usually related to TORS, specifically the safety switch in the clutch/park brake assembly. If it's defective the engine won't rev. Solution: look for a TORS removal kit.

Posted on Aug 21, 2009

  • 1 Answer

SOURCE: 2002 YAMAHA BANSHEE WILL NOT REV

I have a 2004 banshee at the yamaha dealer being worked on.It would not run when i took it up there they cleaned the carbs and put it back together it will start but when you rev it, it holds itself wide open and wont shut down unless you pull the plug wires.they also checked the floats in the carbs said they where ok. they think it is a vent issue with the gas tank or the fuel shut off valve.IS THAT POSSIBLE

Posted on Aug 27, 2009

  • 3567 Answers

SOURCE: banshee running wide open after a couple of revs

The problem with vents is that a vent can get plugged and lessen or completely kill the flow of fuel. They will not make an engine rev wildly. Your banshee has standard carbs. The throttle cables may be routed incorrectly, pinching or stretching the cables. Remove the air filters. Look inside the carbs. Do the slides move freely up and down when the throttle is twisted? In the diagram below note the junction tube on the throttle cabel. The cable can stick at inside the tube. Is the connector hose between the carbs in place? Also, there is a switch on top of the carb. This can go haywire also. Odd that the problem was not present before they cleaned the carbs.
Can I get a “very helpful” rating on this answer?
7e039f3.gif

Posted on Aug 27, 2009

  • 3567 Answers

SOURCE: wont idle unless i havethe throttle barley turned

The idle circuit is still plugged up or it would not be giving you this problem. Remove the carb and dis-assemble it then soak the parts in denatured alcohol for 30 minutes. Then use a spray carb cleaner to finish the job. Spray into all the little holes in the carb body. Especially spray into the air screw and throttle screw holes. Reassemble the carb and LIGHTLY seat the air and throttle screws then turn each of them one and one half turns outward. This is the factory setting. Before putting the slide back into the top of the carb, move the clip on the jet needle one notch lower on the needle. This will richen the low end fuel mix. Install a new spark plug and clean the air filter. Please rate my answer. Thanks.

Posted on Feb 09, 2010

  • 1 Answer

SOURCE: bike boggs down no powerband rm 250

i have a 92 rm 250 an i just had it fully rebuilt an it laggs in power band an splutters an feels guttles

Posted on Apr 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need help with my B/S Engine. Lack of power and black smoke coming from the exhaust.


If the plugs are ok and your engine is not smoking after starting and running ..Sounds like either of three things..all with the carburetor .First the carb has a adjustment screw for air/gas mixture on the side if the carb where it attaches to the engine..try this start the engine and at about half throttle..now adjust the screw clockwise until the engine starts to miss and bogg down then back the other way until it starts missing and bogging again. Then slowly adjust back and forth until you hear the engine run the smoothest..give it more throttle if it starts to run rough do the same procedure until you get the results you want..if it is the mixture problem this will take care of it..if this doesn't it it may be your fuel jet in the bowl dirty or the blow float sticking..if you are not familiar with carbs best to have a professional look at it..you can drop the bowl by removing the bottom bowl and clean it out...check to see if the float easly moves up and down..replace the bowl and go from there..worse scenario new or rebuilt carb...good luck..

Jun 07, 2014 | Briggs & Stratton Garden

1 Answer

Tmec/VIP moped will pull back on throttle then it will bogg down and die not carb just replaced


look inside the exhaust for carbon build up a restricted exhaust will do the t

Oct 14, 2012 | Cars & Trucks

3 Answers

Bike boggs down no powerband rm 250


i have a 92 rm 250 an i just had it fully rebuilt an it laggs in power band an splutters an feels guttles

Oct 09, 2009 | 2003 Suzuki RM 250

3 Answers

Banshee running wide open after a couple of revs


The problem with vents is that a vent can get plugged and lessen or completely kill the flow of fuel. They will not make an engine rev wildly. Your banshee has standard carbs. The throttle cables may be routed incorrectly, pinching or stretching the cables. Remove the air filters. Look inside the carbs. Do the slides move freely up and down when the throttle is twisted? In the diagram below note the junction tube on the throttle cabel. The cable can stick at inside the tube. Is the connector hose between the carbs in place? Also, there is a switch on top of the carb. This can go haywire also. Odd that the problem was not present before they cleaned the carbs.
Can I get a “very helpful” rating on this answer?
7e039f3.gif

Aug 27, 2009 | 1986 Yamaha RD 350

1 Answer

Dieing out


have 04 polaris predator 500 doing the same thing, when giving full throttle it seems to be hitting a limiter a couple of 1000 rpm below full rpm, but will only start with air box disconnected from carby and spitting gas out, might be buggered T.P.S unit have bought new Keihin Flat CR carby with T.P.S on it so to replace one on thumb throttle as it has taken some knocks ( should be able to test T.P.S with volt meter when pushing the throttle), a cdi unit and coil will see how that goes.

Jun 01, 2009 | Polaris ATV

6 Answers

Yamaha warrior atv [yfm 350] bogging problem


Try checking the switch for your parking brake. It is the top wire in the clutch handle boot. This wire connects to your CDI box, and restricts the RPM's while the parking brake is engauged. To find out for sure, trace the wire down to the plug under the headlight assembly and disconnect it. Now try starting you machine and give it some throttle!

Apr 18, 2009 | 2002 Yamaha Road Star Warrior

4 Answers

2002 YAMAHA BANSHEE WILL NOT REV


When was the last time new crank bearings and seals were installed? With all the work you have done on the carb I think the problem is the crank seals. But, check the bearings. At rest, the flywheel must be rock solid > no movement up or down, left or right.

If the bearings are solid then only replace the seals. Chances are the engine can stay in the frame if only the seals are being replaced. Best part is that seals are a low cost item.

One other possibility is a partially blocked exhaust system. Check the exhaust first. Checking the exhaust doesn't cost anything. Disconnect the exhaust pipes from the motor. Excite the neighbors by a quick ride down the street with no muffler. If the problem is instantly fixed then get a new exhaust.

Please rate this solution as " FixYa " if able. Thanks!

Mar 25, 2009 | 1986 Yamaha RD 350

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...