Question about Motorcycles

1 Answer

Flooding carburreters - Motorcycles

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Motorcycles Master
  • 991 Answers

The needle and seats could have dirt in them and are not sealing correctly, clean with some carb cleaner. Float height is incorrect and needs adjusting.

Posted on Apr 07, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 yamaho moto 4 gas comes out of frame and into airbox


Sounds to me that the needle valve in carburreter is sticking/wrongly adjusted

Jan 17, 2014 | Yamaha Moto 4 350 2wd 87 Airbox Air Box

1 Answer

Fluids out when you try to start


double posted, and fluids? you mean FLOODS.
see previous post,
there are other ways to flood any motor.
one other is (iSC /IAC devices are stuck closed) gummed up.
this cause no starting air, no air means flooding.
I cant see your car, and see if starting with 10% throttle solves the flood, but you can.
also WOT cranking, cuts all fueling and can not flood and will start any flooded engine.
but if this still floods,now, that is bad injectors. leaking.
WOT cuts injection pulses dead, and no fuel flows, cranking.
knowing these facts on EFI makes finding causes easy.

Sep 20, 2013 | 1995 Honda Passport

1 Answer

Dies when you turn off the choke


sounds like you have an air flow issue,remove carburreter strip andclean with carb cleaning spray and an airline. Check float height adjustment, once everything has been reassembled, refit carb, prime with fuel and JOB DONE

Mar 05, 2013 | Yamaha Timberwolf 250 2wd 97 Airbox Air...

2 Answers

Floods when cold


Define flooding.

  1. Black smoke out of the tail pipe?

If the fuel return line is plugged,it will flood.If the fuel pressure regulator has lost its vacuum signal ,it will flood.

If there is a large vacuum leak,the O2 will see a lean condition and cause the rich condition.gas mileage will suck,big time.

This "flooding" happens when the engine is cold? ONLY?
Be sure the air filter is not clogged and the PCV is not plugged up solid.
Also,there are a few tubes from the valve cover that vents oil vapors into the air filter housing.

During this flood mode,hold the pedal to the floor and shut the engine OFF-it should NOT keep running.(Leaky injectors)...

Do this when engine is hot and cold.

Dec 25, 2012 | 1990 Volvo 740

1 Answer

Error Code FL


The FL (Over Fill) error code indicates that the flood pressure switch is open (tripped). It is likely that you are getting the LD (Long Drain) fault code because the control detects that the flood pressure switch will not reset after running the drain pump. Your likely failure is in the flood pressure switch

Tapping on the flood pressure switch with the handle of a screw driver may reset it. Reassemble the washer and see if it will work properly. If not, then you will need to replace the flood pressure switch. The part number for the flood pressure switch is 8054767. You can order this part from the Sears PartsDirect website. The part number for the flood pressure switch is 8054767.

Jul 28, 2010 | Kenmore Washing Machines

2 Answers

My car cuts off when i slow down or stop


this is not an easy one to diagnose. I am working on one that does the same thing. I have done a lot of research and this is what I found.
First try seting the idle speed.
If it still stalls it could be the mass air flow sensor. or sometimes it is one or more ignition coils.
The easiest way is not the cheapest, but it is to change one at a time . start with the rear coils first.

Mar 28, 2010 | 1996 Nissan Maxima

2 Answers

My keeway hurricane 50cc suddenly started smoking terribly bad


This may be to the automatic oiler that mixes the oil with the gas. I have a oiler on my 50cc Yamaha Zuma.

Apr 29, 2009 | 2008 Keeway F-act 125

1 Answer

Ryobi petrol strimmer model RCT 2800 refuses to start


Has anyone got a spare cord Pulley for a Ryobi RCT 2800C . The engine seized but I have freed it and now see the plastic spines are damaged on the pulley. I understand the part no is Hayter 683856.

Nov 07, 2008 | Garden

2 Answers

Fisher-Paykel DD603 DishDrawer shows F1 fault code. The Flood Switch has been activated. I need instructions on how to re-set the flood switch. I have two drawers that are possitioned one above the...


Fisher-Paykel DD603 DishDrawer shows F1 fault code. The Flood Switch has been activated. I need instructions on how to re-set the flood switch. I have two drawers that are possitioned one above the other and the are both giving the error of the activated flood switch. Any advice or instruction is greatly appreciated.

Jul 22, 2008 | Dishwashers

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...