Question about 2015 Harley Davidson Softail Slim
Softail slim shows this code when you run threw PN 001120-01 @
Hi, Andy for this scenario you will need your service, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere $9 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at firstname.lastname@example.org. Good luck and have a wonderful day.
Fault code 2015 deluxe Harley Davidson Forums
Harley Davidson Softail Workshop Service Repair Manual 2015 $9 http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
2015 Harley Davidson Softail Slim Owner Manual
Instant Tech Relief
Posted on Oct 12, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: oil drain plug
its not a plug its a hose look under the tank on the pipe side, look for the hose thats goes to the bottom frame rail (tube) thats the drain hopes this helps
Posted on Jan 01, 2009
first take off the brake caliper takes a 10 mm socket..Next jack front of bike up just enough to take pressure off front tire...take off the axle nut lbit more to take pressure off axleock washer and flat washer...Next remove two axle support nuts from the right side of bike 1/2 in socket. now jack bike up a hair more to releave pressure off axle push, hammer with a rubber hammer or what ever it takes to drive it through. jack bike up so it clears fender. Sometimes the tire won't clear the fender bolts if so just release air from tire and it will clear. good luck. Its not hare at all.
Posted on Jun 14, 2009
SOURCE: oil drain plug
Its at the back of crank box right hand side of bike attached to bottom of frame in a sprung clamp just before the softtail swingarm- black hose with a plug and hose clip
Posted on Jul 04, 2009
To change the switch, first unplug the wires at the switch. Screw the old switch out and install the new switch into the tee connector. Do not depress either brake lever while the switch is out. Tighten the switch and reconnect the wires.
Usually you don't have to bleed any air out of the brake system but check the rear brakes for proper operaion. If the rear brake pedal goes too far down, bleed the brakes at the rear caliper. Make sure you don't run the rear brake master cylinder dry while bleeding the rear brake. Use only the approved type of brake fluid, do not mix the different types of fluid. Make sure the rear brakes are working properly before riding the bike.
Posted on Oct 05, 2009
Get the bike standing as straight up as you can without danger of it falling over. This keeps any oil from running out of the primary. Remove the "derby cover" from the outer primary cover giving you access to the clutch adjuster screw in the center of the clutch pressure plate in the primary.
On the clutch cable, slide the rubber boot up or down to expose the adjuster in the cable. It should be on the down tubes of the frame under the fuel tanks. Loosen the lock nut and screw the cable adjuster in as far as it will go thus shortening the cable.
At the clutch back in the primary cover, you'll see a screw that takes a hex allen wrench with a lock nut on it in the center of the clutch pressure plate. Loosen the lock nut and back it off a bit. Screw the screw inwards until you feel a resistance. You want to adjust this in until you feel a resistance, not to the point to where it starts releasing the clutch. Back the screw back out and do this enough times so that you know you are just going to the point of resistance. Turn the screw inward until you get to the point of resistance and then back the screw out 1/2 to 1 full turn. Lock the nut down.
Now, adjust the clutch cable adjuster out making the cable longer You want to adjust the cable until you have about 1/8 inch freeplay at the clutch lever. Lock the cable lock nut and slide the rubber cover over the adjuster. Test ride the bike. If the clutch does not engage exactly where you want it, use the cable adjuster to fine tune where the clutch engages by lengthing or shortening the cable.
Posted on Oct 24, 2009
Tips for a great answer:
Jul 20, 2017 | 2006 Harley Davidson XL 1200 C Sportster...
Jan 13, 2015 | 2006 Harley Davidson XL 1200 C Sportster...
Nov 25, 2017 | 2013 Harley Davidson Softail Slim
Jul 17, 2013 | 2006 Harley Davidson XL 1200 C Sportster...
Apr 18, 2012 | 2000 Harley Davidson FXST Softail Standard
Oct 22, 2010 | 2006 Harley Davidson XL 1200 R Sporster...
Oct 06, 2010 | LG RUMOR Cellular Phone
Jun 02, 2009 | 2003 Harley Davidson FXST Softail Standard
249 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: