Question about 2005 Honda VTX 1300 R

1 Answer

I'm getting electrical noise when I press front brake,noise is coming from ignition button what can it be

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Master
  • 302 Answers

Thats your brake light relay

Posted on May 02, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My car chirps while increasing speed and when I brake my vehicle.


It is possible that the broken tab is your problem because the tabs keep the hardware from moving, especially when you apply the brakes. To determine if this is the case, remove the tire,brake caliper, brake pads, and hardware. Put one of the lug nuts(or two if needed) back on to hold the rotor in place. Spin the rotor by hand and listen for that chirping sound. If you don't hear it, the hardware is the problem. If you can still hear it, check that metal plate that protects the back side of the rotor to make sure its not bent and rubbing against rotor. Also check that nothing is rubbing on the trans-axle(if its front-wheel drive). If all is well in these two places, the only thing left that spins in that area is the wheel bearing. They usually make more of a grinding or roaring sound but sounds can be tricky.. I am a mechanic for a car rental company and often have to diagnose problems by the sound they make. I hope this info is helpful.

Jan 17, 2016 | 2003 Buick LeSabre

2 Answers

Problem starting


What they did was upgrade the system here try this its from Kia.
Turn the ignition key to the "ON" position. Reconnect the negative battery cable. Turn the ignition key to the "OFF" position.
4. Transmitter Programming Procedure:
1. Turn the ignition key to the "ON" position. Do not start the engine.
2. Locate the "disarm/programming" button which is secured to the remote start wire harness behind the left lower dash panel.
3. Press and hold the "disarm/programming" button for 10-15 seconds until the horn beeps 3 times.
4. Release the "disarm" programming button.
5. Press the red Find/Panic button on the remote start transmitter one time. The horn will beep one time indicating that the transmitter code has been learned. Repeat for each additional transmitter.
6. Turn the ignition key to the "OFF" position.
5. Function Check:
Refer to the vehicle specific "Remote Engine Start" installation instructions for a complete list of functions to be verified before delivering the vehicle.

Aug 05, 2012 | 2011 Kia Sorento

2 Answers

Gear noise left front 2008 prius sound like a tire rubbing against a plastic fender but it is not and the faster you go the louder it gets . Even worse when you steer to the right. And quite to the left.


It's most likely a bad left front wheel bearing or possible tire noise, switch the left front tire with the rear tire and see if the noise changes. If not have the wheel bearing checked, it may need to be replaced.

Oct 02, 2011 | 2008 Toyota Prius

1 Answer

I have a 2006 e class elegance and there is a noise coming from the engine bay after about every 4 or 5 presses of the brake pedal . is this aserious problem


no problem, the noise is your brake system... it has an electric motor to pressurize the brake fluid in order to optimize performance and fluid levels to all four brakes.

Apr 06, 2011 | 2006 Mercedes-Benz E-Class

1 Answer

When I apply the brakes i hear a clicking noise like a relay, but only clicks when first applied.


Did you ever find a solution to this. I have the same problem. There is a clicking sound that comes from under the dash when I press on the brakes. I'm investigating because I'm getting electrical noise through the radio when I press on the brakes. The clicking is new.

Jan 02, 2011 | 2004 Ford Expedition

1 Answer

2000 lexus rx300 orange brake light coming on. what could be the problem? comes on everytime we drive it now from the minute we start. intermittently goes off and on along with bell noise. tried mashing...


I am having the same problem. I am thinking it is a sign of the alternator going out. The light and bell sounds also sounded when I pressed the door lock button to lock or open the doors.

Aug 16, 2010 | 2000 Lexus RX 300

1 Answer

Brake noise


Check the front brake pads for wear.
You may need to replace the disc brake pads.

Jan 16, 2010 | 2005 Kia Spectra

1 Answer

My car makes a sqwealing noise when I press on the brakes


That noise you hear, is the brake indicator,letting you know its time to put new pads on.Its a small tab that scrapes on the rotor when the pads get low

Jan 19, 2009 | 2002 Saturn L-Series

Not finding what you are looking for?
2005 Honda VTX 1300 R Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Mike

Level 3 Expert

4340 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...