Question about GAS Motorcycles

1 Answer

I have a miller big 20. It wont start I blew the gas line out not clogged. Ill pour gas in to th manifold n sje will start. I think it is the carb but dont know what todo.

Posted by on

  • guy dubeau Apr 07, 2015

    you will need to clean the carb there are lots of videos on you tube

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Teacher:

    An expert who has written 2 tips or uploaded 1 video tip.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Check carb float

Posted on Apr 07, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 76 Answers

SOURCE: have a honda crf100f 4cycle got spark wont start,

CLEAN THE CARB AGAIN IF IT RUNS ON STARTING FLUID ITS NOT GETTING FUEL YOU WILL NEED TO REMOVE THE JETS AND MAKE SURE THEY ARE CLEAR

Posted on Jan 29, 2010

Benimur
  • 6966 Answers

SOURCE: gas pouring out bottom of carb won't ping out

Hi and welcome to FixYa,

Gas pouring out is an overflow. The only reason there would be an overflow is when the float activated valve does not close the fuel inlet port. This could be caused by dirt, sand, rust or any foreign material. Fix would call for a carb pulldown, soaking non-rubber parts, and cleaning.

Good luck and thank you for asking FixYa.

Posted on Dec 29, 2009

  • 234 Answers

SOURCE: Gas pouring out of carb into air box

sounds like it take bottom of carb off and see if needle is stuck

Posted on Jul 29, 2009

  • 75 Answers

SOURCE: gas overflow line coming from carb is pouring out on a 2001 kaw

the carb needs to be cleaned the float is stuck open and is over filling
cheap and easy fix
good luck

Posted on Jul 08, 2009

  • 2336 Answers

SOURCE: Starting problem

my guess is that the choke being stuck completly closed and the ignition switch where the key go causing a short. thanks anyway

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Miller Bobcat 225. It will not start and run with out pouring gas into the carb? I have changed fuel line and filter? Help!!! Please


Check fuel pump and check carburetor bowl for stuck needle. If fuel was left in engine stuck needle or plugged jets. Confirm that choke is fully closing when cold.

Hope this helps?

Fuel Pump.
maxresdefault-s5y3ewsipro5t2ihgvdymka0-3-2.jpg

Jun 26, 2017 | Miller Welding Tools

1 Answer

Miller 250NT. Why won't it start?


Hello Vic, I would check the needle and seat in the carburetor. Sometimes the float can become stuck from sitting over time and might need to be cleaned.

Oct 11, 2015 | Electrical Supplies

1 Answer

My miller 225 has a kohler engine wont start fuel is getting to the carb float is not stuck carb was not dirty but cleaned it has a soeloid valve and it is getting 12 volts now it will start pouring


Will it start if you put a little gas in the carb before cranking? if it fires then, sounds like a stuck fuel shut off valve, located on bowl. one wire going to it.

Jan 18, 2015 | Miller Welding Tools

1 Answer

Mower will only start with gas poured directly into the cylinder


You need to rebuild the carb. The kits are cheap. Less than $10 for most. If that does not work possible carb replacement needed. Sometimes these carbs get clogged an cant be opened because orifice are to clogged. Carbs are not expensive. For $20- $25 it can be fixed.

Mar 22, 2014 | Mtd Garden

1 Answer

Engine will not start,almost sounds like it is backfireing out of the carburater ,I cleaned out the old gass and put new in, cleaned gas lines,blew out carb with air two times, it ran for about 10 seconds...


Pour a large amount of carb cleaner into the gas tank
With choke on full, pull cord often to work carb cleaner into carb and then let it sit for a day or four.
Your carb is dirty for sure.
The venturi and jets are so small on these carbs that they are easily clogged with gunk from old gas

Aug 05, 2010 | Honda Pressure Washer PSI 3000

2 Answers

Lt1000 20hp. briggs electrics on carb it will run when you pour i


Check fuel lines for clogging.Thanks for asking and I hope this helps out.Please leave me 4 thumbs up.

Jul 13, 2010 | Craftsman 20 hp 42 in. Deck Lawn Tractor -...

1 Answer

Carftsman DYT 4000 42" 18.5 OHV Intek Plus Fuel Problem


Sounds like you have a float problem their is a needle and seat the lets gas into bowl of carburetor if its bad it will not stop letting fuel in the carburetor causing your problem (Be sure to change oil before ing engine over or you could damage engine (with this problem you get gas into case which will remove oil from engine parts inside !

May 09, 2009 | Craftsman 20 hp 42 in. Deck Yard Tractor

1 Answer

Poulan 18' model 2000 chain saw, quit running , will not start.


If you have a compression gauge, check the compression. Anything under 90psi is too low.

Check your flywheel key. If it is broken the flywheel will move and not fire at the correct time.

Note: if it does not sputter with carb cleaner then it's not your carb.

Next:
Remove your exhaust manifold. Look into the cylinder with a flash light. You are looking for scratches. Anything larger then a light fingernail is definite proof you need a new cylinder/piston assy.

If it passes that test do the following:

Pour mixed fuel straight into your cylinder until 1/4 full. Slowly pull your saw over while looking into the cylinder. If you see bubbles after the ring/rings go by then you need a new cylinder/piston assy. On rare occasions if no scratches are present on the cylinder wall or piston, you may be able to change just the rings.

Mar 31, 2009 | Poulan Pro Chain Saw 46cc 20"

1 Answer

I have a 1981 Toyota 4WD with a 22r engine. Truck has been sitting up for about 8mos. I purchased it and got it home. The only way I can start if is by pouring gas in carb. I have replaced all vac lines...


check the fuel pump, maybe it is not working. if you put a new accelerator pump, I wonder if it's same as the fuel pump. if so, maybe you need to rebuild your carb, clean the small fuel line in the carb, something block there.

Jul 27, 2008 | Toyota Pickup Cars & Trucks

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top GAS Experts

Ron Rak
Ron Rak

Level 1 Expert

47 Answers

rugby prop

Level 3 Expert

570 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a GAS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...