Question about Honda Motorcycles

1 Answer

How to adjust a clutch on a 83 Honda 250 dirt bike

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Honda Expert
  • 565 Answers

IF CABLE, loosen the lever end right off, then remove the engine cover where it enters, a 10mm nut will be visible, and a flat screw head, use a screw driver to hold it tight, and 10mm to slacken the lock nut, using screw driver tighten to just a stop, then loosen quarter a turn, lock 10mm nut, keeping flat screw driver holding the head tight, same as any cable bike clutch.

Posted on Apr 14, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 3567 Answers

SOURCE: 2002 Honda XR 250 R new clutch adjustment

No adjustments or measurements needed.. The key thing is the clutch plate installation sequence. If the outer plate is a fiber plate, then you need to be sure the new clutch has a fiber plate as its' outer plate.

Please rate this solution. Thanks brendat_30!

Posted on Apr 05, 2009

  • 3567 Answers

SOURCE: headlight 1972 yamaha 250 yz

You can add a headlight if the type of ignition system on your particular model is the type that will let you. Several different systems were used back then. The proper system will need a lighting coil installed onto the plate underneath the flywheel. The flywheel must be pulled off. You will see a coil there already for the spark. An unused set of threaded screw holes is present, (the same plate was used on the bikes that had a headlight). Just add the coil and now you have power for a headlight.

Posted on May 05, 2009

co7196
  • 3433 Answers

SOURCE: when i pull my clutch lever in, it doesnt engage the clutch

First thing is to make sure you don't have motor oil in the engine. Wet clutches and motor oil are not compatible. Use only the oil sold at motor cycle shops. Do that before tearing into the engine or making any radical adjustments. Good Luck -Ned-

Posted on Sep 21, 2009

  • 46 Answers

SOURCE: Dirt Bike Shifting gears problem(1972 yamaha dt 250 2stroke)

it will be down to adjustment, there are 2 ways to adjust one close to the engine casing and one at the lever just have to get a good balance :)

Posted on Apr 11, 2010

Testimonial: "Exactly what i needed to know thankyou!"

  • 1 Answer

SOURCE: my honda dirt bike won't shift into gear

my honda cb 200 wont change gears

Posted on Feb 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 02 Honda cr125 r and I took clutches and all out and when I put them back in I have no clutch it's lose or hard to squeeze handle and the bike stalls out when I put it in gear pls help me


pull the clutch plates back out and reassemble in the correct order and sequence
best get a workshop manual to see how to do it and how to adjust when finished

Dec 11, 2016 | 2002 Honda CR 125 R

1 Answer

2000 cr 250 clutch spring torque specs


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
97 01 Honda CR250 Clutch Service Torque Specifications Fix Your Dirt Bike
Thread 2002 Cr 250 Torque Setting for Clutch
00 01 cr250r official honda manual zip
http://www.partsfish.com/page/oem-parts-for-honda
http://owners.honda.com/assets/ownerlink/model/own_man/powersports/2007/2007_cr250r.pdf

Jan 22, 2014 | Honda CR 250 R Motorcycles

1 Answer

Torque specs for the clutch on a 1988 Honda CR 250 R


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
97 01 Honda CR250 Clutch Service Torque Specs Fix Your Dirt Bike
1984 CR250 Clutch Torques
1986 1998 Honda CR250R CR500R Engine Service Manual Moto Data Project
https://www.partsfish.com/page/oem-parts-for-honda
Honda CR250R Owner Manual

Aug 17, 2012 | Honda CR 250 R Motorcycles

1 Answer

2001 Honda CBX 250 TWister hard to find neutral


Hi, Hyosgrace and the usual suspects are:
1. Clutch not adjusted properly.
2. Wrong type of clutch oil.
3. Contaminated or damaged fiber plates.
4. Warped steel plates.
5. Clutch basket drive chain too tight.
6. Clutch basket bearing failure.
7. Pressure plate warped or springs too weak.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike will not go into neutral and very difficult shift gear
The International CBX Owners Association
Couldn find neutral when at stop
HONDA CBX250 CBX 250 BIKE WORKSHOP SERVICE REPAIR MANUAL Download Manuals... $15
https://www.partsfish.com/page/oem-parts-for-honda
Honda CBX250 Twister Owner Manual

Oct 25, 2010 | 2001 Honda CBX 250 TWister

1 Answer

Put new clutch in 2003 cr 250.. start bike and let out clutch in 1st gear and bike doesnt move


firstly remove clutch cable at lever, put into gear and see if its hard to push and turns the engine over - if its easy with little resistance then the clutch isnt releasing fully. check the pressure plate springs on clutch unit making sure the plates are squeezed up tight together and that centre hub is located correctly. if it is hard to push then check cable adjustment. hope this helps

Jul 31, 2010 | 2003 Honda CR 250 R

1 Answer

1996 Honda CMX 250 Rebel clutch not engaging


Hi, Dematlock69 and the usual suspects are:
1. Clutch cable adjusted too tight.
2. Pressure plate center screw adjusted too tight
3. A broken clutch rod.
4. Slave cylinder piston stuck.
5. Clutch plate missing from the clutch pack.
6. Clutch plates have worn past minimum specifications.
7. Clutch plates crystallized due to incompatible oil.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Clutch Adjustment Help Needed
HOW TO REPLACE HONDA REBEL CLUTCH TUTORIAL
Honda TWINSTAR 250 Service Repair Maintenance
https://www.partsfish.com/page/oem-parts-for-honda
Honda CMX250C REBEL 2007 Owner Manual

May 14, 2010 | 1996 Honda CMX 250 Rebel

2 Answers

Dirt Bike Shifting gears problem(1972 yamaha dt 250 2stroke)


it will be down to adjustment, there are 2 ways to adjust one close to the engine casing and one at the lever just have to get a good balance :)

Apr 11, 2010 | 1972 Yamaha DT 360

1 Answer

2003 Honda CR 250 R clutch spring bolt torque spec


Hi, Dbrown7904 for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Thread 2002 Cr 250 Torque Setting for Clutch
97 01 Honda CR250 Clutch Service Torque Specifications Fix Your Dirt Bike
CR250 2002 2003 pdf
http://www.partsfish.com/page/oem-parts-for-honda
Honda CR250R Owner Manual Competition Handbook

Apr 02, 2010 | 2003 Honda CR 250 R

1 Answer

When i pull my clutch lever in, it doesnt engage the clutch


First thing is to make sure you don't have motor oil in the engine. Wet clutches and motor oil are not compatible. Use only the oil sold at motor cycle shops. Do that before tearing into the engine or making any radical adjustments. Good Luck -Ned-

Sep 21, 2009 | 2003 Yamaha YZ 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers

yadayada
yadayada

Level 3 Expert

79186 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...