Question about Suzuki Motorcycles

1 Answer

Suzuki gearbox problem gsf 1250

Trouble getting 4 and 5 gear

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Could be a number of things, a worn or loose chain will make finding gears more difficult so check that the chain and sprockets are not excessively worn or loose. An overly stiff or floppy gear lever and linkage can cause problems selecting gears too. If it is neither of these however then it is most likely a bent selector fork in the gear box

Posted on Oct 17, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2336 Answers

SOURCE: raise the seat

First take off the seat, turn it upside down, unscrew the two screws and two bolts that hold the two parts of the seat together. Separate the pillion and rider seat (takes a bit of wiggling), now you can concentrate on the riders seat. undo the four screw that hold all the rubber gromets down (make a note of the direction they are facing), and unbolt the two small bolts on the front. The seat should now come apart, move the bracket at the back of the seat down a hole. Re-attach the two halfs of the seat at the front but this time one hole up. You should see a gap between the two halfs. Put the rubber gromets back on, this is where I went wrong the first time, TURN THE FRONT TWO 180 degrees and leave the back ones how they are. Screw everything back together and you have one raised seat my long legged friend.

Posted on Nov 10, 2008

  • 3567 Answers

SOURCE: suzuki gsf 1200 s bandit

Christmas comes early. Go to the site below and you can download a free PDF service manual. Yours is the 1st one in the "Suzuki GSF" section of the list. 4 or 5 below that is a PDF parts diagram with part numbers.

http://www.carlsalter.com/motorcycle-manuals.asp Most manuals are in English but some are not. There is no way to be sure without doing the download. You can always delete it if in a foreign language.

Top rating due for this answer! Thanks Asel :)

Posted on May 08, 2009

slave2aslave
  • 302 Answers

SOURCE: needs wiring diagram for suzuki banhdit gsf 650 k8

http://netfree1.blogspot.com/2008/09/suzuki-gsf650-bandit-service-repair.html
Hope this helps.

Posted on Nov 19, 2009

  • 623 Answers

SOURCE: 2009 suzuki bandit 1250. bike is hunting between

Look for a vacuum leak either in intakes (where carbs attach to cylinder) or a hose somewhere.

Posted on May 17, 2010

  • 270 Answers

SOURCE: From where can I download Manual of the Suzuki bandit gsf

type the diplodocs.com, then write down the suzuki brand in advance search box, then click the suzuki motorcycle manual, then you can choose different kind of downloadable manual of motorbikes.. try to open the 2009 folder, there is the gsf manual there..

Posted on Jun 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car won't shift into 5th gear


what I can tell you is that there have been a bunch of problems reported on your 5th gear troubles...solution: take it to a garage.


Thanks, Terry

Mar 14, 2014 | Volkswagen Cabriolet Cars & Trucks

1 Answer

Car not going into gear


probably nothing wrong with the clutch or gear box
most likely that the clutch master cylinder and /or clutch slave cylinder has failed
replace both and bleed the system properly
If it turns out to be the clutch ( which I seriously doubt from your statement) you would need a clutch hydraulic system in good condition to handle the extra pressure for the new clutch pressure plate

Mar 09, 2017 | Cars & Trucks

1 Answer

My 2000 Sephia will only shift gears manually from 1,2, then to drive. I get a code PO734. How do I fix and or slove this problem?


This is what your codes mean:

Trouble Code-P0734 (A/T Additional Gear Ratio Error In Fourth Gear)


Trouble Code Conditions:
Vehicle driven to a speed of 4-37 mph at more than 500 rpm, gear selector in 4th Gear in Drive, and the PCM detected too much difference in the engine speed and output shaft speed.
Possible Causes:
  • Customer may complain of intermittent 4th gear operation
  • O/D and 2/4 pressures less than 75 psi
  • O/D or 2/4 clutch volume indexes out of specification
  • O/D accumulator seals are damaged
  • Transmission enters "limp in" mode running in 4th gear

Trouble Code-P0735 (A/T Gear Ratio Error Fourth Prime)

Trouble Code Conditions:
Vehicle driven any forward Gear, and the TCM detected the ratio of the Input speed to the Output Speed did not match the current Gear Ratio (this test can take up to 5 minutes).
Possible Causes:
  • Related Gear Ratio trouble codes may be stored (note that some of these Gear Ratio trouble codes may be intermittent)
  • Transmission has internal problems or damage present
You have a transmission problem.Hope this helps, James Booth

May 17, 2011 | Kia Sephia Cars & Trucks

2 Answers

Code po734, po735


This is what your codes mean:

Trouble Code-P0734 (A/T Additional Gear Ratio Error In Fourth Gear)


Trouble Code Conditions:
Vehicle driven to a speed of 4-37 mph at more than 500 rpm, gear selector in 4th Gear in Drive, and the PCM detected too much difference in the engine speed and output shaft speed.

Possible Causes:

  • Customer may complain of intermittent 4th gear operation
  • O/D and 2/4 pressures less than 75 psi
  • O/D or 2/4 clutch volume indexes out of specification
  • O/D accumulator seals are damaged
  • Transmission enters "limp in" mode running in 4th gear

Trouble Code-P0735 (A/T Gear Ratio Error Fourth Prime)

Trouble Code Conditions:
Vehicle driven any forward Gear, and the TCM detected the ratio of the Input speed to the Output Speed did not match the current Gear Ratio (this test can take up to 5 minutes).

Possible Causes:

  • Related Gear Ratio trouble codes may be stored (note that some of these Gear Ratio trouble codes may be intermittent)
  • Transmission has internal problems or damage present
You have a transmission problem.

Jan 17, 2011 | 2003 Dodge Durango

1 Answer

I am getting the following trouble codes from my 2000 Dodge Durango SLT: P1732 P1734 P0731 P0734 What do these point to?


They all point to your Transmission Governor and Gears. You will need to take your vechile to a Transmission Shop to diagnose the problem

  • P0731 Gear I Incorrect ratio
  • P0734 Gear 4 Incorrect ratio
  • Aug 10, 2010 | 2000 Dodge Durango

    1 Answer

    Im having trouble getting my car 95 ford escort into first gear, all other gears go in fine


    clutch is starting to slip, the first and reverse gears are direct meshing gears, as opposed to the rest that are engaged uing synchros to help mesh the gears. this is why you are having trouble getting them together

    Oct 29, 2009 | 1995 Ford Escort

    1 Answer

    Jeep 1997 Wrangler. Gear shifting very hard


    synchronizers are going bad a used trans would be cheaper than a rebuild due to the labor involved

    Aug 19, 2009 | 1997 Jeep Wrangler

    1 Answer

    325ci automatic gear box stuck


    Have a trouble code test run, you may have an issue with the vehicle speed sensor.

    Nov 10, 2008 | 1996 BMW 318

    Not finding what you are looking for?
    Motorcycles Logo

    Related Topics:

    28 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Suzuki Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Arnie Burke
    Arnie Burke

    Level 3 Expert

    4536 Answers

    Richard
    Richard

    Level 2 Expert

    83 Answers

    Are you a Suzuki Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...