Question about Harley Davidson Motorcycles

1 Answer

Dowse the 97 fat boy have a turn signal relay

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 43,856 Answers

Hi Linda, no it has a turn signal module or canceller that is located on top of the frame tube in between the fuel tanks. Good luck

Posted on Apr 04, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 141 Answers

SOURCE: Turn Signal Installation

wow how did that happen , they should have, well you can by a after market kit that comes with the wiring harness for frt and rear. if it was me thats what i would do . that way you can install some costom lights be ready through they are not cheap kdc744

Posted on Jan 27, 2009

wd4ity
  • 4565 Answers

SOURCE: Want to replace rear brake pads 1995 Harley Fat boy

Replacing the pads on your Fat Boy is not difficult but you need to pay close attention to the way things are put together as you take it apart. Particularly the little steel pad retainers and the anti-rattle spring. These parts are made and go together in such a way that it's very hard to describe how they go in.

To remove the pads, take the two caliper retaining bolts out of the disc brake caliper. These are usually Torx head bolts. Once you get the bolts out, the caliper simply slides to the front and off of the pads. You'll need a way to push the piston back into the caliper so it will go down onto the new pads. I usually do this with a large pair of slip joint pliers. Make sure you put a rag or something on your calipers so you don't damage the piston or the paint.

Now, look at the way the pads, the little steel pieces at each end of the pads and the anti-rattle spring are in the caliper support bracket. Remove the old pads and parts and install the new pads and parts in the same way. Make sure you put the fiber face of the pad TOWARDS THE ROTOR. Don't laugh, I've lots of people put them in backwards, especially on the back side of the rotor.

Now, carefully slide the caliper back down over the pads taking care not to knock the pads out of there positions. I put a little Loctite 242 (med. strength blue) on the threads of the caliper retainer bolts and reinstall them. Torque them to about 25 foot pounds.
Check the brake fluid level in the rear master cylinder and slowly "pump" the rear brake pedal until the rear brake feels firm. Wait a few minutes and mash the brake pedal one time to the bottom. If it goes down to lower point and then on the next "pump" is higher, you probably need to bleed air from the system.

Open the bleeder valve on the caliper, press the rear brake pedal to the bottom and hold it there, close the bleed valve, and then release the brake pedal. Continue to do this until all the air is out of the system and the rear brake pedal feels firm on the first time it's depressed. While doing this, never allow the rear brake fluid reserviour to run out of fluid. If it does, you'll have to start all over with the bleeding process. Use only DOT 5 brake fluid. DOT 5 and DOT 3 or 4 are NOT compatible and will not mix. If they are mixed, it will cause you a lot of trouble in the future.

Test the brakes before you ride the bike and then again when you first ride the bike at a very low speed. Failure to do this job properly can cause serious injury or death. Brakes must operate properly. Good Luck!

Posted on Oct 24, 2009

DJ_MAX1369
  • 119 Answers

SOURCE: relocating front turn signals on 2009 Fat Boy

front turn signal wires should be routed down the right side of the backbone of the frame under the gas tank. they will be violet and brown wires along with 2 blacks for grounds.

Posted on Nov 02, 2009

wd4ity
  • 4565 Answers

SOURCE: Left turn signals not working

Contact me directly and I'll send you a pin out and a trouble shooting guide. wd4ity@bellsouth.net Don't forget to remind me of what you need.

Good Luck
Steve

Posted on Mar 20, 2011

  • 10 Answers

SOURCE: will exhaust from 2003 harley fat boy fit a 1999

Hey. No need for fat jokes on the Internet. That's not cool man.

Posted on May 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of turn signal relay for 2002 harley fatboy


The TSM/TSSM is located in the electrical panel behind the plastic cover directly in front of the rear wheel

May 23, 2014 | 2000 Harley Davidson FLSTF Fat boy

1 Answer

Locate turn signal module 2000 fatboy


Hi Anonymous, on a Softail remove seat and directly behind the battery is a black plastic box. The cover slides up and off revealing the starter relay and the system/fuel pump relay for you injected folks and the various assorted circuit fuses. Good luck

Apr 18, 2012 | 2000 Harley Davidson FLSTF Fat boy

1 Answer

Where is the flasher unit on a 1995 fat boy


Your Fat Boy does not have a conventional flasher unit like on the older cars and bikes. It has a turn signal cancelling unit on it that is a flat looking box about 1/2"thick by about 1" wide and about three inches long. On the Fat Boy, I THINK it's located on the frame between the tanks. It has one large plug on it with a lot of wires going into it.

What is the unit doing or not doing. These units are pretty dependable and usually don't give any trouble. But, they are expensive and you don't want to buy one unless you need one. I have a trouble shooting guide that I'll send you. It's far too much typing to type in here, four full pages with pictures. Contact me directly at wd4ity@bellsouth.net and I'll send it to you.

Good Luck
Steve

Aug 02, 2010 | 2001 Harley Davidson FLSTF - FLSTFI Fat...

1 Answer

Relocating front turn signals on 2009 Fat Boy


front turn signal wires should be routed down the right side of the backbone of the frame under the gas tank. they will be violet and brown wires along with 2 blacks for grounds.

Sep 13, 2009 | 2005 Harley Davidson FLSTF - FLSTFI Fat...

1 Answer

Turn Signal Installation


wow how did that happen , they should have, well you can by a after market kit that comes with the wiring harness for frt and rear. if it was me thats what i would do . that way you can install some costom lights be ready through they are not cheap kdc744

Jan 27, 2009 | 2003 Harley Davidson FLSTF Fat boy

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...