Question about 2005 Harley Davidson FLSTC - FLSTCI Heritage Softail Classic

2 Answers

One screw fell thru when I was removing the seat.

As I was removing the seat, one of the screw slipped back and now I only have 1 of the 2 showing, how do I go about getting the other one back thru so I can attach my seat back?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 195 Answers

IF you see it ,then take a magnet with extension and try to get the screw ,with a little patience!

Posted on Apr 03, 2015

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Harley Davidson Expert
  • 300 Answers

You will have to get you hand up between the rear fender and tyre to push it back through. You might also be able to do it by holding the existing one and moving it about as the two studs are joined together under the fender. A small bit of patience and wiggling should do it.

Posted on Apr 03, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rattle in the rear passenger window/panel


Not sure that I can help you. You will most likely have to remove the seat bottom and maybe the seat back. The seat bottom can come out in 2 different ways. There maybe a bolt on each side of the seat bottom that holds the seat in, or on some you just have to push back hard then pull up on the front of the seat. Some are very hard to get out. the back of the seat be held in by bolts. Then you should be able to remove the 1/4 trim. The 1/4 trim is held on by ribbed push plugs that slip into the trim panel. you can either a panel removing tool or you can use a screw driver and long nose pliers. Be carful that you do not brake the plastic that holds the fastener, but if you do you can drill a small hole and put a sheet metal screw in it. If you do not find the plastic is making the noise might look for a peace of welding rod that the robot left in the car or if the windows go up and down that the bracket are loose or maybe broken. Good luck Jerry

Mar 12, 2014 | 2005 Infiniti G35

1 Answer

2006 s83 seat removal


Should be 3 screws. 1 visible about the halfway mark on each side of the seat and 1 may or may not be visible dead center on back bottom of seat. Mine has a bar with a lock box and pad. I have to remove pad and lock box cover to get to back of seat screw.

Jan 22, 2013 | 2006 Suzuki Boulevard S83

1 Answer

I have a 1988 FLHTP my clutch seems to be slipping. My question is in order to readjust the clutch release mechanism after removing the locknut do I turn the screw counterclockwise and then back a 1/4...


Turn the screw in (clockwise) gently until it seats, then turn it out 1 1/4 to 1 1/2 turns out (counter clockwise). Make sure you take all the adjustment out of the clutch cable before you adjust the clutch. Readjust the cable so you have 1/16 to 1/8 play at the lever after the clutch is adjusted.

Jun 17, 2012 | Harley Davidson Motorcycles

2 Answers

Clutch is slipping on my 2008 flhx how do [ adjust clutch beyond adjustment in cable


take all slack out of cable . take derby cover off loosin lock nut in center if pack tighten addj screw turn in till seats back out 1/2 to 1 turn tighten lock nut . take slack out of cable . hatleytalking.con ...good luck

Oct 29, 2011 | 2008 Harley Davidson FLHX Street Glide

2 Answers

Hi, how do i attach the belt clip that comes with the evenflo booster seat?


If it is the one that is on the end of a strap, at the end of the strap is a loop.
Feed the loop thru a small set of holes in the back of the seat. The seat should have 2 small, close to eachother, holes. It goes in one, out the other and then slide the clip thru the loop and pull it back tight.
The only other design I know of uses a screw to attach the belt, the clip is on, to to a nub with a hole in
it on the back of the car seat.
If by "clip" you mean the little bracket that looks like an "H" you thread the car's seat belt thru it, where the belt goes up to the highest point, and use the H clip to keep that part of the car's seat belt away from the child and car seat by weaving it behind the edge of the car seat.
Use Evenflo's site to download a free manual and it shows you how to do it. All you need is Model number and date of manufacture and it will give you your manual. Save it to your computer. Click this link.

Evenflo Care Seat Manual Downloads

Mar 17, 2011 | Evenflo Baby Gear

1 Answer

Hi,just got a dynojet stage 1/3 kit for my 1980 honda cb650, it's on standard air box, but 4 into 1 exhaust, I take it I should use the stage one kit. Also I have no instructions can you help...


Intended for motorcycles with a stock engine using the stock airbox, air filter and stock pipe. Stage 1 kits are fully adjustable to allow the use of a well designed aftermarket pipes and stock replacement air filters like K&N. Stage 1 kits are designed to improve throttle response and driveability and in most cases power increases of approximately 5% throughout the entire power range can be achieved.


STAGE ONE INSTRUCTIONS
1. Remove the vacuum slide from the carbs. Remove the stock needles & spacers, noting the order of
assembly. Locate the slide lift holes (Fig. A), with the slide drill DD# 14 supplied, enlarge your slide lift
holes. The picture may not show your slide exactly, enlarge your slide lift hole or holes depending on your
model. Do not drill any new lift holes. Do not drill the needle hole.
2. Install Dynojet needles on groove #4, using all stock spacers. Install the Dynojet washers (2 per
needle) above the E-clip.
3. Remove the stock main jets and replace with the Dynojet main jets provided. If you are running with
stock exhaust, use the DJ110 main jets. With an aftermarket header or slip-on with high flowing baffles,
use the DJ116 main jets. Be sure that the jets you are changing are the main jets.
4. Locate the fuel mixture plug (Fig. B), if you see a screw head, proceed to adjusting procedure. With the
DD #5/32 drill bit provided, carefully drill thru the plugs. Note: the mixture screw is directly underneath this
plug, be ready to pull back on the drill the instant you break thru. Use screw provided to secure and
remove the plug. Carefully turn mixture screws clockwise until they seat, turn out 3 turns.


For further info on this, visit: http://www.dynojet.com/jetkits/motorcycle/honda.aspx

You can find the manual for the model you are searching for. Follow the 1st column "CC" to find 650cc models and you can find your specific model after that.

Thanks for asking.
Regards,
Arvind S Iyer

Oct 15, 2010 | Dynojet Cycling

1 Answer

How do you take the driver's seat out of a 1991 jetta?


Unplug the seat belt warning plug, under the seat. You'll need to remove the right side seat track cover, it has 2 plastic inserts holding it down, push the little pin thru the insert. On the other side, at the end of the track, remove the black seat stop. Then at the front of the seat, on the bottom, in the center of the seat, there is a small seat track, at the front of the bracket, you will a screw and a 10mm nut. Remove them, lift up the seat lever (like you were going to move the seat up or back) and slide the seat back until the seat is out of the tracks.

Mar 17, 2010 | 1991 Volkswagen Jetta

1 Answer

Driver side second row seat will not fold down. When pulling the release catch the seat does not release . I can not fold the seat flat to carry a large load in the rear of the vehicle.


I had the same problem. The dealer wanted $400 to replace the latch. I didn't wnat to pay that much so I looked at it and found that the release strap was twisted and jammed in the mechanism. Here's how I fixed it.

I removed the screw from the lever and removed the lever. I pulled apart the plastic housing. It does not come apart all the way but enough to work on it. Pull the release strap that comes out of the back and pull it clear of the mechanism and straighten it out. slip the lever back on and the seat should fold. Fold it up all the way to make it easier to reassemble. Pull the lever back off and slip the release strap back into the slot and make sure it is not twisted or kinked. Snap the housing back together, put the lever back on, and screw it in. Test it and it should work fine. Hope this helps,

Jul 31, 2009 | 2005 Ford Freestyle

1 Answer

Need to clean carseat al eddie bauer online manuals aren't availa


First, snap out the black pieces that attach the cover to the seat with a pair of pliers or a kitchen knife. Then turn the seat over and remove the base by sliding out the metal rod that runs thru the base and seat. Then unhook the center buckle from the bottom of the seat and back up thru the seat. Unhook the straps from the metal bar on the back of the seat and thread them back thru the seat. Be sure to remember the order in which you slide it thru the components so you can reassemble. It may be helpful to lay them out in the order you removed them. Unhook the elastic bands holding the bottom in place and slide it over the top part of the seat and off the seat. If you need to remove the top part and wash, remove the black pieces the same way as the bottom, unhook all elastic and slip it off the top. I wash mine in cold water with mild detergent and usually let it air dry so as to not shrink it. Reassemble by reversing steps.

Jun 06, 2009 | Eddie Bauer 3-In-1 with Latch

Not finding what you are looking for?
2005 Harley Davidson FLSTC - FLSTCI Heritage Softail Classic Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...